Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.04–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the airbag ECU assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2. If a malfunction in the airbag ECU assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 is determined based on a malfunction signal from the brake actuator assembly (skid control ECU), the ECM stores this DTC.

HINT:
·

The airbag ECU assembly (yaw rate and acceleration sensor) signal is sent to the brake actuator assembly (skid control ECU) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·

Output value of the airbag sensor assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 remains below -1.5 G or more than 1.5 G for at least 1.2 seconds or more.

·

Airbag sensor assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 power source voltage is 4.4 V or less, or 5.6 V or higher, for at least 1.2 seconds or more.

·

No signal is detected from the airbag sensor assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 7 times or more.

·

Vehicle is stationary, and the difference between GL1 and GL2 does not decrease below 0.4 G within 60 seconds after it has exceeded 0.6 G.

·

Malfunction signal of the airbag sensor assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 power source voltage has occurred for 10 seconds or more while the vehicle is driven at 3 km/h (1.8 mph) or more.


·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2

·

CAN communication system


Does not come on DTC stored

*1: w/ VSC

*2: w/o VSC


WIRING DIAGRAM

C264292E63
1.042,1.24 1.365,1.458 0.323,0.219 10 false A49 1.031,1.385 2.729,1.792 1.698,0.406 10 false Brake Actuator Assembly (Skid Control ECU) 1.771,0.51 2.292,0.698 0.521,0.188 10 false CANH 1.792,0.938 2.26,1.125 0.469,0.188 10 false CANL 4.927,0.51 5.927,0.896 1,0.385 10 false CANH 4.948,0.948 5.333,1.135 0.385,0.188 10 false CANL 4.917,2.052 5.625,2.354 0.708,0.302 10 false CANH 4.938,2.49 5.323,2.677 0.385,0.188 10 false CANL 0.865,2.271 2.844,2.469 1.979,0.198 10 false to CAN Communication System 0.531,3.458 2.396,3.656 1.865,0.198 10 false : CAN Communication Line 5.073,1.5 5.708,1.792 0.635,0.292 10 false ECM 4.396,3 6.458,3.469 2.063,0.469 10 false Airbag ECU Assembly (Yaw Rate and Acceleration Sensor) 2.271,0.354 2.448,0.51 0.177,0.156 10 false 25 2.271,0.802 2.448,0.958 0.177,0.156 10 false 14 4.667,0.354 4.844,0.51 0.177,0.156 10 false 13 4.677,0.792 4.854,0.948 0.177,0.156 10 false 14 4.656,1.906 4.833,2.063 0.177,0.156 10 false 13 4.667,2.344 4.844,2.5 0.177,0.156 10 false 22 5.073,1.344 5.448,1.49 0.375,0.146 10 false F130 4.396,2.844 4.823,3.042 0.427,0.198 10 false F21 0.094,0.073 2.302,0.313 2.208,0.24 12 false w/ VSC:

C356649E02
0.729,2.323 2.583,2.49 1.854,0.167 10 false : CAN Communication Line 0.125,0.094 0.854,0.313 0.729,0.219 12 false w/o VSC: 1.271,0.594 1.563,0.792 0.292,0.198 10 false GL1 1.167,0.917 1.594,1.115 0.427,0.198 10 false GGND 1.24,1.302 1.583,1.51 0.344,0.208 10 false VGS 1.667,0.469 1.823,0.667 0.156,0.198 10 false 1 1.688,0.823 1.844,0.99 0.156,0.167 10 false 2 1.688,1.208 1.865,1.385 0.177,0.177 10 false 3 3.042,0.583 3.375,0.771 0.333,0.188 10 false GL1 3.021,0.938 3.479,1.115 0.458,0.177 10 false GGND 3.031,1.313 3.417,1.49 0.385,0.177 10 false VGS 2.802,0.49 2.958,0.688 0.156,0.198 10 false 3 2.76,0.833 2.938,1.021 0.177,0.188 10 false 15 2.76,1.198 2.969,1.354 0.208,0.156 10 false 26 0.385,1.729 1,1.927 0.615,0.198 10 false F132 2.896,1.708 3.354,1.906 0.458,0.198 10 false A47 0.375,1.927 1.927,2.115 1.552,0.188 10 false Deceleration Sensor 2.792,1.927 4.479,2.302 1.688,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 5.729,1.708 6.344,1.906 0.615,0.198 10 false F130 5.75,1.917 6.208,2.115 0.458,0.198 10 false ECM 5.594,0.625 6.208,0.823 0.615,0.198 10 false CANH 3.76,0.625 4.167,0.833 0.406,0.208 10 false CANH 5.604,1.208 6.042,1.406 0.438,0.198 10 false CANL 3.781,1.219 4.208,1.427 0.427,0.208 10 false CANL 5.313,0.479 5.563,0.646 0.25,0.167 10 false 13 5.323,1.031 5.521,1.208 0.198,0.177 10 false 14 4.25,1.042 4.531,1.188 0.281,0.146 10 false 14 4.26,0.479 4.552,0.635 0.292,0.156 10 false 25

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.READ VALUE USING GTS (G SENSOR)

B

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of G sensor Min.: 0 V
Max.: 79.998 V
·

2.31 to 2.69 V: Vehicle on level ground

·

1.88 to 2.5 V: Decelerating

·

2.5 to 3.11 V: Accelerating

·

Stuck at 1.87 V: G sensor malfunction

·

Stuck at 1.87 V: Communication malfunction


-
Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

Result:
Result Proceed to
Data List value is not normal (w/ VSC) A
Data List value is normal (w/ VSC) B
Data List value is not normal (w/o VSC) C
Data List value is normal (w/o VSC) D



A

3.REPLACE AIRBAG ECU ASSEMBLY

B

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

C

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - DECELERATION SENSOR ASSEMBLY)

D

8.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
3.REPLACE AIRBAG ECU ASSEMBLY
a.

Replace the airbag ECU assembly (yaw rate and acceleration sensor).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT

4.PERFORM INITIALIZATION
4.PERFORM INITIALIZATION

NEXT

END

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) - DECELERATION SENSOR ASSEMBLY)
a.

Disconnect the F132 deceleration sensor connector.


b.

Disconnect the A47 brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F132-1 (GL1) - A47-3 (GL1) Always Below 1 Ω
F132-2 (GGND) - A47-15 (GGND) Always Below 1 Ω
F132-3 (VGS) - A47-26 (VGS) Always Below 1 Ω
F132-1 (GL1) or A47-3 (GL1) - Body ground Always 10 kΩ or higher
F132-2 (GGND) or A47-15 (GGND) - Body ground Always 10 kΩ or higher
F132-3 (VGS) or A47-26 (VGS) - Body ground Always 10 kΩ or higher



d.

Connect the A47 brake actuator assembly (skid control ECU) connector.


e.

Connect the F132 deceleration sensor connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT DECELERATION SENSOR (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DECELERATION SENSOR (POWER SOURCE)
a.
C199166C09
0.49,1.042 1,1.292 0.51,0.25 1.906,1.229 2.177,1.813 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 2.063,1.865 2.479,2.094 0.417,0.229 10 false VGS 0.583,1.083 0.99,1.323 0.406,0.24 10 false F132
*a Front view of wire harness connector (to Deceleration Sensor)


Disconnect the deceleration sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F132-3 (VGS) - Body ground Ignition switch ON 4.5 to 5.5 V



c.

Connect the deceleration sensor connector.


Result:
Proceed to
OK
NG



OK

7.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)

NG

8.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
7.INSPECT DECELERATION SENSOR (GL1 VOLTAGE)
a.
C277071C03
1.698,1.74 1.698,1.177 true 1.146,1.729 1.469,1.177 true 2.281,1.719 1.948,1.177 true 0.188,0.146 0.5,0.344 0.313,0.198 10 *a 0.927,1.813 1.375,2.021 0.448,0.208 10 VGS 1.49,1.813 2.031,2.042 0.542,0.229 10 GGND 2.25,1.813 2.688,2.063 0.438,0.25 10 GL1
*a Component without harness connected
(Deceleration Sensor)


Remove the deceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>DECELERATION SENSOR>REMOVAL


b.

Connect 3 dry cell batteries of 1.5 V in series.


c.

Connect the positive (+) lead of the batteries to terminal 3 (VGS) and the negative (-) lead to terminal 2 (GGND) to apply a voltage of 4.5 V.


NOTICE:
·

Do not apply 6 V or higher to terminals 3 (VGS) and 2 (GGND).

·

If the sensor is dropped, replace it with a new one.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor not tilted


Approximately
2.5 V
1 (GL1) - 2 (GGND)
·

4.5 V applied to terminals 3 (VGS) and 2 (GGND)

·

Sensor tilted back and forth


Changes between approximately
0.5 V and 4.5 V



HINT:

If the sensor is tilted too much, it may output the wrong value.


Result:
Proceed to
OK
NG



OK

8.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

10.REPLACE DECELERATION SENSOR
8.REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.PERFORM INITIALIZATION
9.PERFORM INITIALIZATION

NEXT

END

10.REPLACE DECELERATION SENSOR

Result:
Proceed to
NEXT



NEXT

4.PERFORM INITIALIZATION