Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.

The circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1805/52 Short in Front Passenger Side Squib Circuit
·

The airbag ECU assembly receives a line short circuit signal in the front passenger side squib circuit during primary check.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1806/52 Open in Front Passenger Side Squib Circuit
·

The airbag ECU assembly receives an open circuit signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1807/52 Short to GND in Front Passenger Side Squib Circuit
·

The airbag ECU assembly receives a short circuit to ground signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1808/52 Short to B+ in Front Passenger Side Squib Circuit
·

The airbag ECU assembly receives a short circuit to B+ signal in the front passenger side squib circuit.

·

Front passenger side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly (Front passenger side squib)

·

Airbag ECU assembly


DTC corresponds to check mode.

WIRING DIAGRAM

C281462E01
0.406,3.74 0.719,3.938 0.313,0.198 10 false D1 0.406,3.885 2.969,4.281 2.563,0.396 10 false Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib) 1.823,1.833 2.031,2.01 0.208,0.177 10 false P+ 2.094,1.833 2.208,1.99 0.115,0.156 10 false 2 1.833,3.052 2.021,3.208 0.188,0.156 10 false P- 2.083,3.052 2.219,3.219 0.135,0.167 10 false 1 3.396,3.135 3.708,3.333 0.313,0.198 10 false FD1 3.479,2.958 3.792,3.156 0.313,0.198 10 false 2 3.396,1.938 3.708,2.135 0.313,0.198 10 false FD1 3.458,1.74 3.604,1.885 0.146,0.146 10 false 1 5.073,1.833 5.24,2 0.167,0.167 10 false 4 5.24,1.948 5.552,2.146 0.313,0.198 10 false P+ 5.24,3.156 5.552,3.354 0.313,0.198 10 false P- 5.063,3.052 5.167,3.219 0.104,0.167 10 false 3 5.177,4.615 5.49,4.813 0.313,0.198 10 false F21 5.177,4.76 6.646,4.979 1.469,0.219 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C352088C01
1.094,3.281 0.833,2.667 false 2.323,1.906 1.99,1.24 false 2.417,4.333 2,3.438 false 0.75,4.333 0.333,3.438 false 0.667,1.917 0.323,1.219 false 1.083,1.083 0.75,0.5 false 0.188,0.167 0.5,0.365 0.313,0.198 12 false *A 0.531,0.354 0.781,0.521 0.25,0.167 10 false *3 2.396,1.781 2.708,1.979 0.313,0.198 10 false *4 2.854,1.219 3.167,1.417 0.313,0.198 10 false *2 2.854,3.583 3.167,3.781 0.313,0.198 10 false *2 2.5,4.208 2.813,4.406 0.313,0.198 10 false *4 0.729,1.813 1.042,2.01 0.313,0.198 10 false *1 0.833,4.229 1.146,4.427 0.313,0.198 10 false *1 0.469,1.073 0.625,1.271 0.156,0.198 10 false F 0.469,3.271 0.625,3.469 0.156,0.198 10 false F 1.333,3.271 1.49,3.469 0.156,0.198 10 false D 0.729,1.073 0.885,1.271 0.156,0.198 10 false E 0.729,3.271 0.885,3.469 0.156,0.198 10 false E 1.625,1.073 1.781,1.271 0.156,0.198 10 false C 1.625,3.271 1.781,3.469 0.156,0.198 10 false C 1.333,1.073 1.49,1.271 0.156,0.198 10 false D 2.51,1.063 2.667,1.26 0.156,0.198 10 false A 2.5,3.271 2.656,3.469 0.156,0.198 10 false A 2.24,1.063 2.396,1.26 0.156,0.198 10 false B 2.229,3.271 2.385,3.469 0.156,0.198 10 false B 0.208,2.26 0.583,2.5 0.375,0.24 12 false *B 0.625,2.5 0.938,2.698 0.313,0.198 10 false *3
*A w/o VSC
*B w/ VSC
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the instrument panel passenger airbag assembly and airbag ECU assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the instrument panel passenger airbag assembly and airbag ECU assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the instrument panel passenger airbag assembly side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Result Proceed to
OK (w/o VSC) A
OK (w/ VSC) B
NG C



A

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

B

7.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

C

REPLACE WIRE HARNESS

2.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
C281406C01
0.594,2.302 0.938,2.521 0.344,0.219 0.354,0.99 0.365,0.667 false 2.063,2.271 2.313,2.146 false 0.302,1.021 0.615,1.177 0.313,0.156 10 false *1 2.635,0.677 2.948,0.833 0.313,0.156 10 false *2 0.344,1.719 0.656,1.875 0.313,0.156 10 false *a 0.49,0.51 0.677,0.698 0.188,0.188 10 false F 0.896,0.51 1.083,0.698 0.188,0.188 10 false E 1.375,0.51 1.563,0.698 0.188,0.188 10 false D 1.531,0.51 1.719,0.698 0.188,0.188 10 false C 2.167,0.51 2.323,0.708 0.156,0.198 10 false A 2.021,0.51 2.177,0.708 0.156,0.198 10 false B 0.698,2.333 1.01,2.531 0.313,0.198 10 false D1 2.354,2.052 2.813,2.25 0.458,0.198 10 false SST
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib))


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)

NG

3.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) CIRCUIT
3.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) CIRCUIT
a.
C281401C02
0.604,2.292 0.927,2.51 0.323,0.219 0.365,1.146 0.354,0.646 false 1.646,2.063 2,1.906 true 1.469,2.073 1.104,1.865 true 0.313,1.177 0.625,1.333 0.313,0.156 10 false *1 2.604,0.656 2.917,0.813 0.313,0.156 10 false *2 0.292,1.771 0.604,1.927 0.313,0.156 10 false *a 0.5,0.5 0.688,0.667 0.188,0.167 10 false F 0.802,0.5 0.99,0.667 0.188,0.167 10 false E 1.417,0.49 1.604,0.656 0.188,0.167 10 false C 1.26,0.49 1.448,0.656 0.188,0.167 10 false D 1.823,0.5 2.01,0.667 0.188,0.167 10 false B 2.177,0.49 2.365,0.656 0.188,0.167 10 false A 0.906,1.771 1.219,1.969 0.313,0.198 10 false P- 2.052,1.802 2.365,2 0.313,0.198 10 false P+ 0.688,2.323 1,2.521 0.313,0.198 10 false D1
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D1-2 (P+) - Body ground Ignition switch ON Below 1 V
D1-1 (P-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - Body ground Always 1 MΩ or higher
D1-1 (P-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG ECU ASSEMBLY

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK AIRBAG ECU ASSEMBLY
a.
C281421C01
0.667,1.552 0.479,1.01 false 2,0.854 2.156,1.052 0.156,0.198 10 false A 1.854,0.854 2.01,1.052 0.156,0.198 10 false B 1.365,0.854 1.521,1.052 0.156,0.198 10 false C 1.219,0.854 1.375,1.052 0.156,0.198 10 false D 0.74,0.854 0.896,1.052 0.156,0.198 10 false E 0.594,0.844 0.75,1.042 0.156,0.198 10 false F 0.656,1.573 0.969,1.771 0.313,0.198 10 false *1 2.438,1.031 2.75,1.229 0.313,0.198 10 false *2
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.
C281407C01
0.74,2.385 1.083,2.604 0.344,0.219 0.323,1.031 0.281,0.667 false 1.021,0.5 1.146,0.188 false 1.896,1.073 1.781,0.656 false 0.271,1.073 0.583,1.229 0.313,0.156 10 false *1 2.635,0.656 2.948,0.813 0.313,0.156 10 false *2 1.135,0.073 1.448,0.229 0.313,0.156 10 false *3 1.917,0.99 2.229,1.146 0.313,0.156 10 false *4 0.385,1.781 0.698,1.938 0.313,0.156 10 false *a 0.427,0.5 0.583,0.688 0.156,0.188 10 false F 0.74,0.51 0.896,0.698 0.156,0.188 10 false E 1.188,0.51 1.344,0.698 0.156,0.188 10 false D 1.49,0.5 1.646,0.688 0.156,0.188 10 false C 1.938,0.5 2.094,0.688 0.156,0.188 10 false B 2.25,0.5 2.406,0.688 0.156,0.188 10 false A 0.792,2.406 1.25,2.604 0.458,0.198 10 false FD1
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the No. 2 instrument panel wire from the instrument panel wire.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FD1-1 - Body ground Ignition switch ON Below 1 V
FD1-2 - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - FD1-2 Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - Body ground Always 1 MΩ or higher
FD1-2 - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - FD1-2 Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

6.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C281404C02
0.594,2.333 0.896,2.531 0.302,0.198 0.26,1.125 0.323,0.656 false 1.198,1.063 0.99,0.656 false 1.948,1.063 1.74,0.656 false 1.604,2.073 1.969,1.938 true 0.917,1.927 1.438,2.073 true 0.115,1.073 0.427,1.292 0.313,0.219 10 false *1 1.177,1.063 1.49,1.219 0.313,0.156 10 false *2 2.708,0.667 3.021,0.823 0.313,0.156 10 false *3 1.948,1.063 2.167,1.281 0.219,0.219 10 false *4 0.302,1.802 0.615,1.958 0.313,0.156 10 false *a 0.427,0.5 0.635,0.75 0.208,0.25 10 false F 0.729,0.5 0.938,0.75 0.208,0.25 10 false E 1.188,0.5 1.396,0.75 0.208,0.25 10 false D 1.49,0.5 1.698,0.75 0.208,0.25 10 false C 1.938,0.5 2.146,0.75 0.208,0.25 10 false B 2.26,0.5 2.469,0.75 0.208,0.25 10 false A 0.76,1.854 1.073,2.052 0.313,0.198 10 false P- 1.99,1.844 2.302,2.042 0.313,0.198 10 false P+ 0.656,2.333 0.969,2.531 0.313,0.198 10 false D1
*1 Front Passenger Side Squib
*2 No. 2 Instrument Panel Wire
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly (Front Passenger Side Squib))


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D1-2 (P+) - Body ground Ignition switch ON Below 1 V
D1-1 (P-) - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - Body ground Always 1 MΩ or higher
D1-1 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the condition.


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.
C256970C07
0.5,2.177 1,2.417 0.5,0.24 0.25,0.917 0.375,0.656 false 2.063,2.281 2.25,2.167 false 0.302,1.677 0.667,2.063 0.365,0.385 10 false *a 2.177,0.51 2.542,0.896 0.365,0.385 10 false A 2.021,0.51 2.385,0.896 0.365,0.385 10 false B 1.531,0.51 1.896,0.896 0.365,0.385 10 false C 1.375,0.51 1.74,0.896 0.365,0.385 10 false D 0.896,0.51 1.26,0.896 0.365,0.385 10 false E 0.5,0.5 0.865,0.885 0.365,0.385 10 false F 2.635,0.833 3,1.219 0.365,0.385 10 false *2 0.063,0.833 0.333,1.073 0.271,0.24 10 false *1 2.302,2.052 2.74,2.438 0.438,0.385 10 false SST 0.646,2.198 1.083,2.583 0.438,0.385 10 false D1
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly )


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

8.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY CIRCUIT
8.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY CIRCUIT
a.
C256977C20
0.5,2.167 1,2.417 0.5,0.25 0.25,0.917 0.365,0.656 true 1.115,1.917 1.49,2.083 true 1.656,2.083 1.969,1.885 true 0.052,0.833 0.354,1.083 0.302,0.25 10 false *1 2.594,0.792 2.948,1.094 0.354,0.302 10 false *2 0.292,1.74 0.646,2.042 0.354,0.302 10 false *a 0.656,2.208 1.083,2.5 0.427,0.292 10 false D1 1.865,0.5 2.156,0.792 0.292,0.292 10 false B 2.177,0.5 2.448,0.781 0.271,0.281 10 false A 1.406,0.5 1.708,0.771 0.302,0.271 10 false C 1.26,0.5 1.51,0.875 0.25,0.375 10 false D 0.813,0.5 1.146,0.885 0.333,0.385 10 false E 0.5,0.5 0.969,0.896 0.469,0.396 10 false F 2.01,1.813 2.344,2.052 0.333,0.24 10 false P+ 0.938,1.833 1.25,2.031 0.313,0.198 10 false P-
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly )


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D1-2 (P+) - Body ground Ignition switch ON Below 1 V
D1-1 (P-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - Body ground Always 1 MΩ or higher
D1-1 (P-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

9.CHECK AIRBAG ECU ASSEMBLY

NG

10.CHECK INSTRUMENT PANEL WIRE
9.CHECK AIRBAG ECU ASSEMBLY
a.
C238235C09
0.5,0.875 0.417,1.167 false 2.438,1.031 2.75,1.313 0.313,0.281 10 false *2 0.25,1.083 0.5,1.333 0.25,0.25 10 false *1 0.635,0.74 1.188,1.167 0.552,0.427 10 false F 0.792,0.74 1.188,1.083 0.396,0.344 10 false E 1.24,0.74 1.594,1.083 0.354,0.344 10 false D 1.396,0.74 1.698,1.167 0.302,0.427 10 false C 1.844,0.74 2.135,1.042 0.292,0.302 10 false B 2,0.74 2.271,0.969 0.271,0.229 10 false A
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTCs B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

10.CHECK INSTRUMENT PANEL WIRE
a.
C238255C27
0.5,2.167 1,2.417 0.5,0.25 1.625,2.594 1.313,2.792 true 1.833,2.583 2.146,2.781 true 0.99,0.656 1.083,1 false 1.667,0.25 1.75,0.5 true 0.302,0.667 0.396,1.01 false 0.427,0.51 0.771,0.865 0.344,0.354 10 false F 0.74,0.51 1.031,0.865 0.292,0.354 10 false E 1.188,0.51 1.5,0.802 0.313,0.292 10 false D 1.5,0.51 1.802,0.823 0.302,0.313 10 false C 1.938,0.51 2.208,0.844 0.271,0.333 10 false B 2.25,0.51 2.563,0.865 0.313,0.354 10 false A 2.688,0.813 3.146,1.104 0.458,0.292 10 false *2 0.375,1.76 0.76,2.073 0.385,0.313 10 false *a 1.104,2.729 1.531,3.052 0.427,0.323 10 false P+ 0.583,2.198 1.01,2.5 0.427,0.302 10 false FD1 2.188,2.729 2.594,3.042 0.406,0.313 10 false P- 0.448,1.01 0.896,1.406 0.448,0.396 10 false *1 1.125,1 1.521,1.292 0.396,0.292 10 false *3 1.5,0.083 1.75,0.333 0.25,0.25 10 false *4
*1 Front Passenger Side Squib
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the No. 2 instrument panel wire from the instrument panel wire.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FD1-1 - Body ground Ignition switch ON Below 1 V
FD1-2 - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - FD1-2 Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - Body ground Always 1 MΩ or higher
FD1-2 - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FD1-1 - FD1-2 Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

11.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C256975C19
0.417,2.25 0.917,2.49 0.5,0.24 1.833,0.917 1.76,0.646 true 1.042,1.958 1.438,2.094 true 1.604,2.094 1.948,1.958 true 0.25,0.917 0.333,0.667 true 0.99,0.5 0.917,0.229 true 0.083,0.885 0.396,1.083 0.313,0.198 10 false *1 2.677,0.802 3.042,1.125 0.365,0.323 10 false *2 0.281,1.76 0.635,2.042 0.354,0.281 10 false *a 0.75,0.083 1.063,0.281 0.313,0.198 10 false *3 1.917,0.917 2.198,1.25 0.281,0.333 10 false *4 0.552,2.292 0.927,2.552 0.375,0.26 10 false D1 0.854,1.875 1.135,2.125 0.281,0.25 10 false P- 1.99,1.875 2.302,2.115 0.313,0.24 10 false P+ 2.26,0.51 2.531,0.802 0.271,0.292 10 false A 1.948,0.51 2.198,0.781 0.25,0.271 10 false B 1.5,0.5 1.708,0.75 0.208,0.25 10 false C 1.188,0.5 1.417,0.813 0.229,0.313 10 false D 0.438,0.5 0.75,0.823 0.313,0.323 10 false F 0.74,0.49 0.927,0.771 0.188,0.281 10 false E
*1 Front Passenger Side Squib
*2 No. 2 Instrument Panel Wire
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly )


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D1-2 (P+) - Body ground Ignition switch ON Below 1 V
D1-1 (P-) - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - Body ground Always 1 MΩ or higher
D1-1 (P-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-2 (P+) - D1-1 (P-) Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the condition.


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO.2 INSTRUMENT PANEL WIRE