Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Pretensioner Squib LH Circuit  B1906/74  Open in Front Pretensioner Squib LH Circuit  B1907/74  Short to GND in Front Pretensioner Squib LH Circuit  B1908/74  Short to B+ in Front Pretensioner Squib LH Circuit  


DESCRIPTION

The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.

This circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1905/74 Short in Front Pretensioner Squib LH Circuit
·

The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1906/74 Open in Front Pretensioner Squib LH Circuit
·

The airbag ECU assembly receives an open circuit signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1907/74 Short to GND in Front Pretensioner Squib LH Circuit
·

The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1908/74 Short to B+ in Front Pretensioner Squib LH Circuit
·

The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit.

·

Front pretensioner squib LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly LH (Front pretensioner squib LH)

·

Airbag ECU assembly


DTC corresponds to check mode.

WIRING DIAGRAM

C222225E90
4.604,4.854 6.635,5.083 2.031,0.229 10 false Airbag ECU Assembly 1.052,3.729 3.26,4.063 2.208,0.333 10 false Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH) 1.052,3.563 1.365,3.74 0.313,0.177 10 false F24 2.708,2.115 2.865,2.292 0.156,0.177 10 false 1 2.719,2.948 2.875,3.135 0.156,0.188 10 false 2 4.635,2.219 4.948,2.365 0.313,0.146 10 false PL+ 4.635,3.052 4.906,3.198 0.271,0.146 10 false PL- 2.458,2.125 2.771,2.323 0.313,0.198 10 false L+ 2.479,2.958 2.667,3.167 0.188,0.208 10 false L- 4.281,1.938 4.594,2.115 0.313,0.177 10 false 4*1 4.323,2.792 4.583,3 0.26,0.208 10 false 5*1 4.583,4.688 6.417,4.885 1.833,0.198 10 false F22*1, F119*2 2.073,4.573 3.76,4.771 1.688,0.198 10 false *1: w/o VSC 2.083,4.854 3.615,5.052 1.531,0.198 10 false *2: w/ VSC 4.281,2.135 4.74,2.333 0.458,0.198 10 false 2*2 4.313,2.948 4.771,3.146 0.458,0.198 10 false 1*2

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C352085C01
0.583,2.271 0.333,1.521 false 1.677,4.469 1.427,3.719 false 1.688,2.281 1.438,1.531 false 0.583,4.469 0.333,3.719 false 0.208,0.333 0.583,0.573 0.375,0.24 12 false *A 0.208,2.927 0.583,3.167 0.375,0.24 12 false *B 0.667,2.167 0.979,2.365 0.313,0.198 10 false *1 0.635,4.365 0.948,4.563 0.313,0.198 10 false *1 2.833,1.219 3.146,1.417 0.313,0.198 10 false *2 2.833,3.583 3.146,3.781 0.313,0.198 10 false *2 1.75,2.167 2.063,2.365 0.313,0.198 10 false *3 1.75,4.365 2.063,4.563 0.313,0.198 10 false *3 2.51,1.365 2.667,1.563 0.156,0.198 10 false A 2.51,3.573 2.667,3.771 0.156,0.198 10 false A 2.26,1.375 2.417,1.573 0.156,0.198 10 false B 2.26,3.583 2.417,3.781 0.156,0.198 10 false B 0.719,1.375 0.875,1.573 0.156,0.198 10 false C 0.688,3.583 0.844,3.781 0.156,0.198 10 false C 0.458,1.385 0.615,1.583 0.156,0.198 10 false D 0.458,3.583 0.615,3.781 0.156,0.198 10 false D
*A w/o VSC
*B w/ VSC
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly
*3 Instrument panel wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly LH and airbag ECU assembly.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the front seat outer belt assembly LH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Result Proceed to
OK (w/o VSC) A
OK (w/ VSC) B
NG C



A

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

B

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

C

REPLACE INSTRUMENT PANEL WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)
a.
C281409C02
0.365,2.344 0.771,2.594 0.406,0.25 0.552,1.542 0.708,1.094 false 1.792,2.344 2.104,2.344 false 0.823,0.948 1.021,1.135 0.198,0.188 10 false D 2.292,0.802 2.604,0.958 0.313,0.156 10 false *2 0.406,1.51 0.719,1.667 0.313,0.156 10 false *1 1.167,0.948 1.333,1.146 0.167,0.198 10 false C 0.5,3.417 0.813,3.573 0.313,0.156 10 false *3 0.354,1.927 0.667,2.083 0.313,0.156 10 false *a 0.469,2.396 0.927,2.594 0.458,0.198 10 false F24 2.125,2.25 2.583,2.448 0.458,0.198 10 false SST
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH))


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)

NG

3.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
3.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.
C281410C04
0.583,2.281 0.969,2.51 0.385,0.229 1.406,1.052 1.104,0.521 false 0.552,1.479 0.698,1.208 false 1.615,2.24 1.938,2 true 1.396,2.219 0.99,2.01 true 0.823,1.042 0.979,1.24 0.156,0.198 10 false D 1.125,1.042 1.323,1.229 0.198,0.188 10 false C 0.948,0.427 1.177,0.615 0.229,0.188 10 false *3 0.396,1.448 0.708,1.604 0.313,0.156 10 false *1 2.302,0.875 2.615,1.031 0.313,0.156 10 false *2 1.573,1.042 1.719,1.24 0.146,0.198 10 false B 1.885,1.042 2.094,1.25 0.208,0.208 10 false A 0.271,1.844 0.583,2 0.313,0.156 10 false *a 0.667,2.313 1.125,2.51 0.458,0.198 10 false F24 0.833,1.865 1.146,2.063 0.313,0.198 10 false L+ 1.969,1.854 2.281,2.052 0.313,0.198 10 false L-
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly
*3 Instrument panel wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F24-1 (L+) - Body ground Ignition switch ON Below 1 V
F24-2 (L-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - F24-2 (L-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - Body ground Always 1 MΩ or higher
F24-2 (L-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - F24-2 (L-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK AIRBAG ECU ASSEMBLY
a.
C281411C01
1.115,1.948 0.833,1.448 false 0.969,1.292 1.167,1.5 0.198,0.208 10 false D 1.125,1.292 1.344,1.469 0.219,0.177 10 false C 1.146,1.927 1.458,2.083 0.313,0.156 10 false *1 2.167,1.135 2.479,1.292 0.313,0.156 10 false *2
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 / B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH (FRONT PRETENSIONER SQUIB LH)
a.
C241759C12
0.417,2.25 0.719,2.49 0.302,0.24 0.667,0.906 0.667,1.302 false 1.802,2.292 1.979,2.292 false 0.594,1.313 0.948,1.604 0.354,0.292 10 false *1 2.229,0.771 2.594,1.167 0.365,0.396 10 false *2 1.813,0.75 2.208,1.24 0.396,0.49 10 false A 1.656,0.75 2.135,1.156 0.479,0.406 10 false B 1.146,0.75 1.51,1.198 0.365,0.448 10 false C 0.781,0.75 1.156,1.146 0.375,0.396 10 false D 0.438,2.271 0.969,2.552 0.531,0.281 10 false F24 2.01,2.208 2.479,2.469 0.469,0.26 10 false SST 0.292,1.677 0.615,1.948 0.323,0.271 10 false *a
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

6.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
6.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT)
a.
C241760C12
0.479,2.385 0.802,2.615 0.323,0.229 1.625,2.302 1.833,2.25 true 1.167,2.25 1.417,2.333 true 0.563,0.802 0.333,0.417 true 1.385,0.802 1.167,0.417 true 0.125,0.333 0.875,0.615 0.75,0.281 10 false *1 2.406,0.781 2.927,1.135 0.521,0.354 10 false *2 1.948,0.781 2.375,1.198 0.427,0.417 10 false A 1.573,0.792 1.896,1.25 0.323,0.458 10 false B 1.073,0.781 1.49,1.167 0.417,0.385 10 false C 0.688,0.781 1.021,1.135 0.333,0.354 10 false D 1.917,2.167 2.219,2.469 0.302,0.302 10 false L- 0.99,2.135 1.438,2.427 0.448,0.292 10 false L+ 0.302,1.823 0.792,2.26 0.49,0.438 10 false *a 0.531,2.417 0.906,2.802 0.375,0.385 10 false F24 0.99,0.323 1.438,0.667 0.448,0.344 10 false *3
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly
*3 Instrument panel wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F24-1 (L+) - Body ground Ignition switch ON Below 1 V
F24-2 (L-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - F24-2 (L-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - Body ground Always 1 MΩ or higher
F24-2 (L-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-1 (L+) - F24-2 (L-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

7.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK AIRBAG ECU ASSEMBLY
a.
C238245C27
0.844,1.146 0.844,1.458 false 0.969,1 1.219,1.385 0.25,0.385 10 false D 1.125,1 1.333,1.417 0.208,0.417 10 false C 1.583,1 1.823,1.354 0.24,0.354 10 false B 1.74,1 2,1.323 0.26,0.323 10 false A 2.167,0.99 2.458,1.313 0.292,0.323 10 false *2 0.76,1.479 1.083,1.781 0.323,0.302 10 false *1
*1 Front Pretensioner Squib LH
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.


HINT:

Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG