Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › 2016.04–2017.10
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM J

2NR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).

*1: w/o Smart Entry and Start System

*2: w/ Smart Entry and Start System

*3: for CVT

*4: for Manual Transaxle


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SIGNAL)

B

23.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Result Proceed to
NG (for CVT) A
NG (for Manual Transaxle) B
OK C



A

3.INSPECT PARK/NEUTRAL POSITION SWITCH

B

9.INSPECT CLUTCH START SWITCH ASSEMBLY

C

15.INSPECT ST RELAY
3.INSPECT PARK/NEUTRAL POSITION SWITCH
a.

Inspect the park/neutral position switch.

Click hereDrivetrain>K312 CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Smart Entry and Start System) A
OK (w/o Smart Entry and Start System) B
NG C



A

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH - ECM)

B

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

REPLACE PARK/NEUTRAL POSITION SWITCH

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - B19-4 (B) Always Below 1 Ω
F44-16 (STAR) - B47-15 (NSW) Always Below 1 Ω
F44-16 (STAR), B19-4 (B) or B47-15 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the B19 park/neutral position switch connector.


b.

Remove the ST relay from the engine room relay block.


c.

Disconnect the B47 ECM connector.


d.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-17 (STA) - B19-9 (L) Always Below 1 Ω
B47-17 (STA) - 2 (ST Relay holder) Always Below 1 Ω
B47-17 (STA) - F44-37 (STA) Always Below 1 Ω
B19-9 (L), 2 (ST Relay holder), B47-17 (STA) or F44-37 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2NR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the F7 ignition or starter switch assembly connector.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-7 (ST2) - B19-4 (B) Always Below 1 Ω
F7-7 (ST2) - B47-15 (NSW) Always Below 1 Ω
F7-7 (ST2), B19-4 (B) or B47-15 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY - ECM)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Remove the ST relay from the engine room relay block.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B19-9 (L) - B47-17 (STA) Always Below 1 Ω
2 (ST Relay holder) - B47-17 (STA) Always Below 1 Ω
B19-9 (L), 2 (ST Relay holder) or B47-17 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Smart Entry and Start System) A
OK (w/o Smart Entry and Start System) B
NG C



A

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ECM)

B

12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

C

REPLACE CLUTCH START SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-16 (STAR) - A28-2 Always Below 1 Ω
F44-16 (STAR) or A28-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block.


c.

Disconnect the B47 ECM connector.


d.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-17 (STA) - A28-1 Always Below 1 Ω
B47-17 (STA) - 2 (ST Relay holder) Always Below 1 Ω
B47-17 (STA) - F44-37 (STA) Always Below 1 Ω
A28-1, 2 (ST Relay holder), B47-17 (STA) or F44-37 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2NR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the F7 ignition or starter switch assembly connector.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-7 (ST2) - A28-2 Always Below 1 Ω
F7-7 (ST2) or A28-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY - ECM)
a.

Disconnect the A28 clutch start switch assembly connector.


b.

Remove the ST relay from the engine room relay block.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-1 - B47-17 (STA) Always Below 1 Ω
2 (ST Relay holder) - B47-17 (STA) Always Below 1 Ω
A28-1, 2 (ST Relay holder) or B47-17 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT ST RELAY

Result:
Proceed to
OK
NG



OK

16.INSPECT STARTER ASSEMBLY

NG

REPLACE ST RELAY

16.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2NR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the B15 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST Relay holder) - B15-1 Always Below 1 Ω
3 (ST Relay holder) or B15-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the B28 starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - B28-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
a.
A301476C03
0.146,0.198 0.458,0.354 0.313,0.156 10 false *1 0.229,1.469 0.542,1.625 0.313,0.156 10 false *2
*1 Engine Room Relay Block
*2 ST Relay Holder


Remove the ST relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST Relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

20.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - BODY GROUND)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (Starter relay assembly holder) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for CVT) A
OK (for Manual Transaxle) B
NG C



A

21.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)

B

22.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (STARTER RELAY ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
a.

Remove the starter relay assembly from the engine room relay block.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (Starter relay assembly holder) - B19-9 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (ST RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the A28 clutch start switch assembly connector.


c.

Disconnect the B47 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST Relay holder) - A28-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

OK:
Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)