This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| B1500 | Fuel Sender Open Detected | When IG voltage is 9.5 V or more and the following condition is detected:
·
Average input signal of fuel sender gauge assembly is 550 Ω or more 3 times consecutively |
·
Harness or connector ·
Fuel sender gauge assembly ·
Fuel suction tube with pump and gauge assembly ·
Combination meter assembly |
- | - |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-37 (L) - F38-36 (E) | Always | 13.5 to 414.5 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F28 fuel suction tube with pump and gauge assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-37 (L) - F28-2 (FS) | Always | Below 1 Ω |
| F38-37 (L) or F28-2 (FS) - Body ground | Always | 10 kΩ or higher |
| F38-36 (E) - F28-3 (FE) | Always | Below 1 Ω |
| F38-36 (E) or F28-3 (FE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
for 1NZ-FE
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2NZ-FE
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL
Inspect the fuel sender gauge assembly.
for 1NZ-FE
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for 2NZ-FE
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
| NG (for 1NR-FE) | D |
| NG (for 2NR-FE) | E |
A
B
C
D
E
| *a | Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly) |
| *b | Connector A |
| *c | Connector B |
Remove the fuel suction tube with pump and gauge assembly.
for 1NZ-FE
Click hereEngine / Hybrid System>1NZ-FE FUEL>FUEL PUMP>REMOVAL
for 2NZ-FE
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL PUMP>REMOVAL
for 1NR-FE
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL PUMP>REMOVAL
for 2NR-FE
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL PUMP>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-2 (FS) - B-2 | Always | Below 1 Ω |
| A-3 (FE) - B-1 | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
| NG (for 1NR-FE) | D |
| NG (for 2NR-FE) | E |
A
B
C
D
E