Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.04–2016.07
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

w/ ABS

The meter CPU receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication system (CAN V Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on the pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores the DTCs. Troubleshoot the Anti-lock Brake System.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1275




w/o ABS

The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speedometer sensor.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION



WIRING DIAGRAM

E279001E06
0.083,0.073 1.604,0.323 1.521,0.25 12 false w/ ABS: 0.135,3.073 1.74,3.427 1.604,0.354 10 false Brake Actuator Assembly (Skid Control ECU) 2.927,3.167 4.646,3.385 1.719,0.219 10 false : CAN Communication Line 5.281,3.073 7.156,3.313 1.875,0.24 10 false Combination Meter Assembly

E270882E07
0.083,0.083 1.771,0.365 1.688,0.281 12 false w/o ABS: 2.344,1.156 2.656,1.354 0.313,0.198 10 false SI 2.26,2.146 2.573,2.344 0.313,0.198 10 false IG+ 2.271,2.531 2.583,2.729 0.313,0.198 10 false SE 2.563,1.042 2.875,1.24 0.313,0.198 10 false 3 2.542,2.031 2.854,2.229 0.313,0.198 10 false 1 2.552,2.427 2.865,2.625 0.313,0.198 10 false 2 1.625,3.083 1.938,3.281 0.313,0.198 10 false B22 1.625,3.26 3.177,3.646 1.552,0.385 10 false Speedometer Sensor 3.813,1.042 4.125,1.24 0.313,0.198 10 false 34 4.031,1.156 4.344,1.354 0.313,0.198 10 false SI 3.969,1.635 4.281,1.833 0.313,0.198 10 false F38 3.958,1.771 6.146,2.052 2.188,0.281 10 false Combination Meter Assembly 4.813,2.135 6.625,2.396 1.813,0.26 10 false from IG1 NO. 2 Fuse

CAUTION / NOTICE / HINT

NOTICE:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

6.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are output. A
CAN communication DTCs are not output. B



A

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160, 200 -
Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS(VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS(VEHICLE SPEED METER)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h
(0 mph)
Max.: 255 km/h
(158 mph)
Almost the same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
OK:

Vehicle speed displayed on the GTS is almost the same as the speedometer indication.



Result:
Proceed to
OK
NG



OK

5.CHECK FOR DTC

NG

REPLACE COMBINATION METER ASSEMBLY

5.CHECK FOR DTC
a.

Check if vehicle stability control system or anti-lock brake system DTCs are output.


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. (w/o VSC) B
DTCs are output. (w/ VSC) C




A

REPLACE COMBINATION METER ASSEMBLY

B

C

6.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160, 200 -
Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

7.INSPECT SPEEDOMETER SENSOR

NG

REPLACE COMBINATION METER ASSEMBLY

7.INSPECT SPEEDOMETER SENSOR

OK

8.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)

NG

REPLACE COMBINATION METER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the B22 speedometer sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-34 (SI) - B22-3 (SI) Always Below 1 Ω
F38-34 (SI) or B22-3 (SI) - Body ground Always 10 kΩ or higher



d.

Reconnect the F38 combination meter assembly connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
B22-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR