IGNITION SWITCH EXPRESSIONS
The type of ignition switch used on this model differs depending on specifications of the vehicle.
The expressions listed in the table below are used in this section.
| Expression | Ignition Switch (Position) | Engine Switch (Condition) |
|---|---|---|
| Ignition switch off | LOCK | Off (Lock) |
| Ignition switch ACC | ACC | On (ACC) |
| Ignition switch ON | ON | On (IG) |
| Engine Start | START | Start |
PRECAUTIONS
Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) battery terminal.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Do not work on the fuel system near any open flames. Never smoke when working on this system.
Keep gasoline away from rubber or leather parts.
DISCHARGE FUEL SYSTEM PRESSURE
Perform this procedure when the engine coolant temperature is below 60°C (140°F).
Perform the following procedure to prevent fuel from spilling out before removing any fuel system parts.
Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.
Remove the rear seat cushion assembly.
for Separate Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Seat Type)>REMOVAL
for Fixed Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Fixed Seat Type)>REMOVAL
Check for DTCs.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
Remove the rear floor service hole cover.
Click hereEngine / Hybrid System>1NR-FE EMISSION CONTROL>CANISTER>REMOVAL
Start the engine.
After the engine stops naturally, turn the ignition switch off.
Do not increase the engine speed or drive the vehicle while waiting for the engine to stop naturally.
Crank the engine again and make sure that the engine does not start.
Disconnect the cable from the negative (-) battery terminal.
Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.
Install the rear floor service hole cover.
Click hereEngine / Hybrid System>1NR-FE EMISSION CONTROL>CANISTER>INSTALLATION
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Install the rear seat cushion assembly.
for Separate Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Seat Type)>INSTALLATION
for Fixed Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Fixed Seat Type)>INSTALLATION
FUEL SYSTEM
When disconnecting the high-pressure fuel line, a large amount of gasoline will splash out. Take the following precautions.
Discharge the fuel system pressure.
Disconnect the fuel tank main tube sub-assembly.
Click hereEngine / Hybrid System>1NR-FE EMISSION CONTROL>CANISTER>REMOVAL
Drain the fuel remaining inside the fuel tank main tube sub-assembly into a container.
Cover the disconnected pipe and connector with plastic bags to prevent damage and contamination.
Do not damage the fuel pipe or fuel tube connector, and prevent entry of foreign objects.
Put a container under the connection part.
Perform the following procedure when disconnecting the fuel tube connector.
|
Pull |
Remove the EFI fuel pipe clamp. (Clamp Type)
|
Pull |
Release the lock of the fuel tube connector cover. (Cover Type)
Check whether there is any foreign matter on the fuel pipe around the fuel tube connector before disconnecting it and remove the foreign matter as necessary.
| *1 | Retainer |
| *2 | Nylon Tube |
| *3 | Fuel Pipe |
| *4 | O-ring |
| *5 | Fuel Tube Connector |
|
Pinch |
|
Pull Out |
Pinch the retainer of the fuel tube connector, and then pull out the fuel tube connector to disconnect the fuel tube from the fuel pipe.
Be sure to disconnect the fuel tube connector by hand.
|
Pull |
|
Push |
If the fuel tube connector and fuel pipe are stuck, push in and pull on the fuel tube connector to release it. Pull the fuel tube connector out of the fuel pipe carefully.
Be sure to disconnect the fuel tube connector by hand.
Check that there is no dirt or other foreign matter on the sealing surfaces of the disconnected fuel pipes. Clean the surfaces if necessary.
Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.
Do not damage the fuel pipe or fuel tube connector, and prevent entry of foreign matter.
|
Push |
Perform the following procedure when connecting a fuel tube connector.
Check if there is any damage or foreign matter on the connecting parts of the fuel pipes.
Line up the 2 parts of the fuel pipes to be connected, and push them together until the fuel tube connector makes a "click" sound.
If the fuel pipe is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.
|
Pull |
After connecting the fuel pipes, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.
Install the EFI fuel pipe clamp. (Clamp Type)
Engage the lock of the fuel tube connector cover. (Cover Type)
INJECTOR
| *1 | Fuel Delivery Pipe |
| *2 | O-ring |
| *3 | Injector Vibration Insulator |
Install the fuel injector assembly to the fuel delivery pipe and cylinder head sub-assembly, as shown in the illustration. Apply gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and fuel injector assembly before installing the fuel injector assembly.
| *1 | O-ring |
| *2 | Fuel Delivery Pipe |
| *a | Correct |
| *b | Incorrect |
Observe the following precautions when removing and installing the fuel injector assembly.
Do not reuse the O-ring and injector vibration insulator.
When placing a new O-ring onto the fuel injector assembly, do not damage the O-ring.
Coat a new O-ring with gasoline or spindle oil before installing it.
Do not use engine oil, gear oil or brake fluid.
INSPECT FOR FUEL LEAK
Check that there is no fuel leakage after performing maintenance anywhere on the fuel system.
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION