Home › Engine / Hybrid System › 1NR-FE FUEL › FUEL INJECTOR › from 2016.04
RM30M0E _51 Engine / Hybrid System _053554 1NR-FE FUEL _0259935 FUEL INJECTOR A

1NR-FE FUEL  FUEL INJECTOR  REMOVAL  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 17880 3.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 23841B 4.REMOVE EFI FUEL PIPE CLAMP

a.
A304867

Remove the EFI fuel pipe clamp from the fuel tube sub-assembly and fuel delivery pipe.


Hide 23901 5.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A304868C01
1.146,1.938 1.25,1.802 false 0.656,1.917 0.531,1.76 false 2.354,2.604 2.198,2.417 true 2.594,2.51 2.698,2.375 false 1.198,3.198 1.323,3.01 false 1.979,3 2.052,3.25 2.052,3.25 2.115,3 true 2.833,3.146 2.698,2.948 false 1.24,1.667 1.552,1.823 0.313,0.156 10 false *1 1.01,3.135 1.323,3.292 0.313,0.156 10 false *2 2.875,3.115 3.188,3.271 0.313,0.156 10 false *3 1.99,3.26 2.302,3.417 0.313,0.156 10 false *4 2.74,2.292 3.052,2.448 0.313,0.156 10 false *5 0.375,1.667 0.688,1.823 0.313,0.156 10 false *1 2.01,2.323 2.323,2.479 0.313,0.156 10 false *1
*1 Retainer
*2 Nylon Tube
*3 Fuel Delivery Pipe
*4 O-ring
*5 Fuel Tube Connector
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube sub-assembly off of the fuel delivery pipe.

NOTICE:
·

Check for foreign matter on the fuel tube sub-assembly around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel delivery pipe.

·

Do not use any tools to separate the fuel tube connector and fuel delivery pipe.

·

Do not forcibly bend, kink or twist the nylon tube.

·

Keep the fuel tube connector and fuel delivery pipe free from foreign matter.

·

If the fuel tube connector and fuel delivery pipe are stuck, push and pull to release them.

·

Put the fuel tube connector and fuel delivery pipe in plastic bags to prevent damage and contamination.




Hide 23814B 6.REMOVE FUEL DELIVERY PIPE

a.

Make sure that there are no deposits such as sand or grit near the fuel injector assembly, and if there are any deposits, clean them away.

NOTICE:

Do not allow foreign matter to enter any other components.



b.
A383251

Disconnect the 4 fuel injector assembly connectors.


c.
A383252

Remove the 2 bolts and fuel delivery pipe together with the 4 fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:
·

Do not allow foreign matter to enter the cylinder head sub-assembly.

·

Do not drop the fuel injector assemblies when removing the fuel delivery pipe.




Hide 23891 7.REMOVE NO. 1 FUEL DELIVERY SPACER

a.
A305601

Remove the 2 No. 1 fuel delivery spacers from the cylinder head sub-assembly.


Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

a.
A383253C01
0,0 0,0 false
V100135

Pull


Pull the 4 fuel injector assemblies out of the fuel delivery pipe.


b.

Remove the O-ring from each fuel injector assembly.

NOTICE:
·

Do not allow foreign matter to enter the fuel delivery pipe.

·

Prevent entry of foreign matter by covering the fuel injector assemblies with plastic bags.



HINT:

For reinstallation, attach a tag or label with the corresponding cylinder number to each fuel injector assembly shaft.



c.
A304873

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.