Home › Engine / Hybrid System › 1NR-FE INTAKE / EXHAUST › EXHAUST MANIFOLD › 2016.04–2016.07
RM30M0E _51 Engine / Hybrid System _053550 1NR-FE INTAKE / EXHAUST _0260000 EXHAUST MANIFOLD A

1NR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 25051 1.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

a.
A171211C01
0.927,1.875 0.927,1.438 false 1.604,1.927 1.604,1.573 false 1.823,0.635 2,0.385 false 2.469,0.99 2.646,0.74 false 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 1.552,1.927 1.865,2.083 0.313,0.156 10 false *2 2.021,0.281 2.333,0.438 0.313,0.156 10 false *a 2.656,0.646 2.969,0.802 0.313,0.156 10 false *b
*1 Exhaust Manifold Converter Sub-assembly
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.




b.

Install a new exhaust manifold to head gasket to the cylinder head sub-assembly.


c.

Temporarily install the exhaust manifold converter sub-assembly to the cylinder head sub-assembly with 5 new nuts.


d.
A313692E01
1.927,0 2.083,0.198 0.156,0.198 10 true 1 1.26,0.844 1.417,1.042 0.156,0.198 10 true 2 2.646,0.26 2.802,0.458 0.156,0.198 10 true 5 0.906,0.635 1.063,0.833 0.156,0.198 10 true 4 2.271,0.75 2.427,0.948 0.156,0.198 10 true 3

Tighten the 5 nuts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17118 2.INSTALL MANIFOLD STAY

a.
A313691E01
1.688,0.313 1.844,0.51 0.156,0.198 10 false 1 2,0.802 2.156,1 0.156,0.198 10 true 2

Temporarily install the manifold stay to the exhaust manifold converter sub-assembly and cylinder block sub-assembly with the bolt and a new nut.


b.

Tighten the bolt and nut in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 3.CONNECT FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Free Length of Compression Spring:
Standard Length Minimum Length
42 mm (1.65 in.) 40.5 mm (1.59 in.)


If the length is not as specified, replace the compression spring.


b.
A247549C09
0.142,0.277 0.307,0.439 0.165,0.162 10 *1 0.142,1.031 0.307,1.192 0.165,0.162 10 *2 2.046,1.233 2.211,1.395 0.165,0.162 10 *3 2.768,1.321 2.933,1.482 0.165,0.162 10 *a 0.325,0.375 0.547,0.596 false 0.526,0.892 0.325,1.109 false 2.115,1.233 1.983,0.923 false
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Connect the front exhaust pipe sub-assembly to the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

Torque:

43 N*m (440 kgf*cm, 32 ft.*lbf)


NOTICE:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



c.

Engage the clamp to connect the heated oxygen sensor wire to the wire harness clamp bracket.


d.

Connect the heated oxygen sensor connector.


Hide 17168 4.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

A313689E01
2.333,1.281 2.49,1.479 0.156,0.198 10 true 1 0.719,1.521 0.875,1.719 0.156,0.198 10 true 2 1.969,1.969 2.115,2.146 0.146,0.177 10 true 3

a.

Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 27060 7.INSTALL GENERATOR WITH REGULATOR ASSEMBLY

Hide 8.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION