Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › IGNITION SYSTEM › from 2016.04
RM30M0E _51 Engine / Hybrid System _053310 1NR-FE ENGINE CONTROL _0260014 IGNITION SYSTEM G

1NR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Check for DTCs.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.

Remove the 4 No. 1 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL

NOTICE:

If the No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:

Arrange the removed parts in the correct order.



c.
A382347

Disconnect the 4 fuel injector assembly connectors.

NOTICE:

Perform this step in order to stop fuel injection to prevent damage to the catalyst due to unburned fuel.



d.
A381926

Install a spark plug to each No. 1 ignition coil and connect the No. 1 ignition coil connectors.


e.

Ground the spark plugs.


f.

Check that sparks occur while the engine is being cranked.


g.

Check whether sparks occur.

NOTICE:
·

Ground the spark plugs when checking them.

·

Do not crank the engine for more than 2 seconds.

- For vehicles with a cranking hold function, turn the ignition switch off during cranking to stop cranking.

·

If the No. 1 ignition coil is struck or dropped, replace it.

·

If the spark plug is struck or dropped, replace it.




h.

If sparks do not occur, perform the following procedure.


i.

Install the 4 spark plugs and 4 No. 1 ignition coils.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:
·

Install the same parts to their original positions.

·

When assembling the No. 1 ignition coil to the cylinder head cover sub-assembly, press and continue to hold the No. 1 ignition coil so that it is fully inserted into the plug tube while tightening.






Hide 2.INSPECT IGNITION COIL AND SPARK TEST

HINT:

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.

Perform the spark test in accordance with the following procedure.

i.

Check that the wire harness side connector of the No. 1 ignition coil is securely connected.

Result:
Result Proceed to
OK Go to next step
NG Connect securely



b.

Perform a spark test on each No. 1 ignition coil.

i.

If there is a cylinder where sparks do not occur, replace its No. 1 ignition coil with the No. 1 ignition coil of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating No. 1 ignition coil.

Result:
Result Proceed to
OK Replace No. 1 ignition coil
(Click here)
NG Go to next step

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.




c.

Perform a spark test on each spark plug.

i.

If there is a cylinder where sparks do not occur, replace its spark plug with the spark plug of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating spark plug.

Result:
Result Proceed to
OK Replace spark plug
(Click here)
NG Inspect ignition system
(Click here)

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.




d.

Connect the 4 fuel injector assembly connectors.


e.

Install the 4 No. 1 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION

NOTICE:

If a No. 1 ignition coil or spark plug has been struck or dropped, replace it.


HINT:
·

Install the same parts to their original positions.

·

When assembling the No. 1 ignition coil to the cylinder head cover sub-assembly, press and continue to hold the No. 1 ignition coil so that it is fully inserted into the plug tube while tightening.






Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Be careful not to damage the iridium tip or platinum tip of the spark plug.

·

Check the iridium tip visually as it is easily damaged.

·

Never attempt to adjust the electrode gap of a used spark plug.

·

If the spark plug is extremely dirty with oil, etc., replace it.

·

Replace a spark plug if it is damaged at all.

·

When installing a new spark plug, do not remove the protective cap from the spark plug tip until just before installing the spark plug to the engine.

·

If the spark plug has been struck or dropped, replace it.



HINT:

Perform "Inspection After Repair" after replacing a spark plug.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
I109591C02
0.719,2 1.073,1.969 false 0.552,1.927 0.865,2.083 0.313,0.156 10 false *a
*a Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (Terminal part) - Ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method:

NOTICE:

Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected)


i.

Start the engine.


ii.

Quickly accelerate the engine to 4000 rpm 5 times.



iv.
A126881

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Spark Plug Type
DENSO SC16HR11



d.
A126880C15
0.708,1.115 1.042,1.396 0.333,0.281 10 *a
*a Electrode Gap


Reference:

i.

Check the spark plug electrode gap.

Maximum electrode gap for a used spark plug:

1.3 mm (0.0512 in.)


If the electrode gap is more than the maximum, replace the spark plug.

Electrode gap for a new spark plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.





Hide 4.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a No. 1 ignition coil or spark plug.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION