Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › 2016.04–2016.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090850 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*1).
HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.


·

AM2 NO. 2 fuse

·

ACC relay (Driver side junction block assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off.
HINT:

To turn the engine switch on (ACC), carry an electrical key transmitter sub-assembly and press the engine switch with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 released.



*1: Only detected while a malfunction is present.

*2: for Automatic Transaxle and CVT

*3: for Manual Transaxle


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the engine switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).


HINT:

The engine switch can be turned on (IG) and the engine can be started.


-

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


Starting Control
·

Ignition


-

WIRING DIAGRAM

B348675E02
0.156,1.083 1.052,1.563 0.896,0.479 10 false from Battery 1.396,1.25 2.771,1.448 1.375,0.198 10 false AM2 NO. 2 2.542,0.969 2.698,1.167 0.156,0.198 10 false 1 2.719,1.083 3.031,1.281 0.313,0.198 10 false +B 2.51,2.156 2.823,2.354 0.313,0.198 10 false 10 2.719,2.25 2.875,2.448 0.156,0.198 10 false E 3.083,1.771 3.698,1.969 0.615,0.198 10 false ACCD 3.542,1.646 3.854,1.844 0.313,0.198 10 false 21 2.448,2.854 2.906,3.052 0.458,0.198 10 false F43 2.427,3.01 3.99,3.438 1.563,0.427 10 false Certification ECU (Smart Key ECU Assembly) 4.292,2.49 6.625,2.688 2.333,0.198 10 false Driver Side Junction Block Assembly 4.094,1.333 4.406,1.531 0.313,0.198 10 false 2A 4.094,1.74 4.406,1.938 0.313,0.198 10 false 2F 6.458,1.333 6.771,1.531 0.313,0.198 10 false 2L 6.438,1.75 6.75,1.948 0.313,0.198 10 false 2J 5.219,1.49 6.531,1.677 1.313,0.188 10 false SFT LOCK-ACC*1 5.385,1.083 6.25,1.281 0.865,0.198 10 false ECU-ACC*2 4.135,1.146 4.292,1.344 0.156,0.198 10 false 1 6.479,1.167 6.635,1.365 0.156,0.198 10 false 3 6.479,1.583 6.635,1.781 0.156,0.198 10 false 7 4.125,1.583 4.281,1.781 0.156,0.198 10 false 2 4.698,2.083 5.302,2.271 0.604,0.188 10 false ACC 0.021,3.094 2.271,3.448 2.25,0.354 10 false *1: for Automatic Transaxle and CVT 0.021,3.417 1.802,3.604 1.781,0.188 10 false *2: for Manual Transaxle

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 2F and 2J driver side junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-21 (ACCD) - 2F-2 Always Below 1 Ω
2J-7 - Body ground Always Below 1 Ω
F43-21 (ACCD) or 2F-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B342624C01
1.031,0.333 1.417,0.583 0.385,0.25 2.615,0.333 3,0.583 0.385,0.25 4.167,0.333 4.552,0.583 0.385,0.25 5.75,0.333 6.135,0.583 0.385,0.25 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 1.135,0.365 1.448,0.563 0.313,0.198 10 false 2A 2.729,0.365 3.042,0.563 0.313,0.198 10 false 2L 4.281,0.365 4.594,0.563 0.313,0.198 10 false 2F 5.865,0.365 6.177,0.563 0.313,0.198 10 false 2J
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2A-1 - 2L-3 Battery voltage not applied to terminals 2F-2 and 2J-7 10 kΩ or higher
Battery voltage applied to terminals 2F-2 and 2J-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the certification ECU (smart key ECU assembly) connector.

B342590C03
2.563,0.302 2.979,0.552 0.417,0.25 2.51,1.417 2.167,2.25 true 0.052,0.031 0.365,0.188 0.313,0.156 10 false *a 2.656,0.333 3.115,0.531 0.458,0.198 10 false F43 1.958,2.25 2.5,2.5 0.542,0.25 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F43-21 (ACCD) - Body ground Engine switch off → Engine switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)