Home › Engine / Hybrid System › 1NR-FE ENGINE MECHANICAL › CAMSHAFT › from 2016.04
RM30M0E _51 Engine / Hybrid System _053932 1NR-FE ENGINE MECHANICAL _0262342 CAMSHAFT A

1NR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 11310 1.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 13540 2.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Set the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft in the positions (20° ATDC) shown in the illustration.

A313958C03
3.927,0.75 4.208,0.531 4.208,0.531 3.948,0.604 true 3.938,0.667 4.188,0.542 true 4.865,0.656 5.208,0.542 5.208,0.542 4.875,0.594 true 1.719,4.104 1.99,3.771 true 4.802,0.24 5.063,0.396 0.26,0.156 10 false 11° 4.24,0.448 4.552,0.604 0.313,0.156 10 false *a 5.271,0.438 5.583,0.594 0.313,0.156 10 false *a 3.875,0.229 4.135,0.385 0.26,0.156 10 false 11° 2.427,3.688 2.76,3.833 0.333,0.146 10 false 23° 2.344,4.031 2.677,4.177 0.333,0.146 10 false 20° 2.438,3.865 2.75,4.021 0.313,0.156 10 false *b 1.615,4.104 1.927,4.26 0.313,0.156 10 false *a
*a Timing Mark *b TDC



b.
A313928C01
1.5,1.198 1.635,1.063 false 2.135,1.323 2.49,1.635 true 1.313,1.177 1.5,1.344 0.188,0.167 10 true *1 2.438,1.677 2.646,1.854 0.208,0.177 10 true *2 1.302,0.677 1.49,0.854 0.188,0.177 10 true *a 2,1.573 2.177,1.729 0.177,0.156 10 true *b
*1 Stopper Plate
*2 Plunger
*a Push Down
*b Push


Push down the stopper plate to release the lock and push in the plunger.


c.
A313929C01
1.552,1.198 1.792,0.948 true 1.375,1.177 1.688,1.333 0.313,0.156 10 false *1 1.365,0.677 1.563,0.865 0.198,0.188 10 true *a
*1 Stopper Plate
*a Pull Up


Pull up the stopper plate with the plunger pushed to the end and lock the plunger.


d.
A313930C01
0.844,1.323 1.073,0.958 true 0.74,1.354 0.917,1.531 0.177,0.177 10 false *a
*a Pin of 3 mm diameter


Insert a pin of 3 mm (0.118 in.) diameter to the hole in the stopper plate.


e.
A313931

Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.


Hide 13562 3.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A313932

Remove the 2 bolts and No. 2 chain vibration damper from the camshaft bearing cap.


Hide 13591 4.REMOVE TIMING CHAIN TENSION ARM

a.
A313933

Remove the timing chain tension arm from the cylinder block sub-assembly.


Hide 13506 5.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly from the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft.


Hide 13566B 6.REMOVE TIMING CHAIN GUIDE

a.
A313934

Remove the 2 bolts and timing chain guide from the cylinder head sub-assembly and cylinder block sub-assembly.


Hide 13070A 7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check the lock of the camshaft timing exhaust gear assembly.

i.
A313935C01
1.688,0.292 2.229,0.458 true 1.646,0.594 2.583,0.531 true 1.635,1.958 2.604,2.563 true 1.5,0.188 1.667,0.354 0.167,0.167 10 false *a 1.469,0.5 1.781,0.656 0.313,0.156 10 false *b 2.688,2.51 3,2.667 0.313,0.156 10 false *c
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the exhaust side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure B)


iii.
A313936

Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the hole pricked in procedure B to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




iv.

Using a screwdriver with its tip wrapped in protective tape, forcibly turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).

NOTICE:
·

Be sure to keep the camshaft timing exhaust gear assembly in the retard direction (clockwise) using a screwdriver. If the camshaft timing exhaust gear assembly is released, it will return to the most advanced position automatically due to force from the spring.

·

Do not damage the camshaft timing exhaust gear assembly.




v.
A313937C01
0.76,1.677 1.177,1.26 true 0.604,1.677 0.917,1.833 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times without turning it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.


vi.

Remove the adhesive tape from the camshaft bearing cap.



Hide 13050 8.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.

i.
A313938C01
1.156,0.438 1.656,0.198 true 0.813,0.51 1.563,0.698 true 0.406,2.323 1.063,1.615 true 1.708,0.094 2.021,0.25 0.313,0.156 10 false *a 1.615,0.646 1.927,0.802 0.313,0.156 10 false *b 0.292,2.354 0.604,2.51 0.313,0.156 10 false *c
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the intake side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)


iii.
A313939

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.




iv.

Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.



v.
A313940

Turn the camshaft timing gear assembly within its movable range (22 to 24°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.


vi.

Remove the adhesive tape from the camshaft bearing cap.



Hide 13070A 9.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A313941C01
0.573,2.74 0.458,2.365 0.458,2.365 0.76,2.448 true 0.844,3.177 1.5,3.052 1.5,3.052 1.063,3.042 true 1.458,0.063 1.771,0.219 0.313,0.156 10 false *a 1.229,0.708 1.427,0.875 0.198,0.167 10 true *b 0.292,2.26 0.51,2.406 0.219,0.146 10 false *c 1.542,2.99 1.76,3.135 0.219,0.146 10 false *c
*a Hold
*b Turn
*c Do not remove


Remove the bolt while holding the hexagonal portion of the No. 2 camshaft, then remove the camshaft timing exhaust gear assembly from the No. 2 camshaft.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing exhaust gear assembly horizontal while removing it from the No. 2 camshaft.




Hide 13050 10.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A313942C01
0.802,2.719 0.479,2.448 0.479,2.448 0.948,2.521 true 0.99,3.083 1.563,3.198 1.563,3.198 1.167,2.875 true 1.427,0.156 1.74,0.313 0.313,0.156 10 false *a 0.781,0.698 1.031,0.896 0.25,0.198 10 true *b 0.292,2.344 0.604,2.5 0.313,0.156 10 false *c 1.594,3.146 1.906,3.302 0.313,0.156 10 false *c
*a Hold
*b Turn
*c Do not remove


Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly from the camshaft.

NOTICE:
·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.




Hide 11.REMOVE CAMSHAFT BEARING CAP

a.
A313943E02
0.26,0.781 0.417,0.979 0.156,0.198 10 true 2 2.51,0.927 2.667,1.125 0.156,0.198 10 true 3 1.99,0.927 2.146,1.125 0.156,0.198 10 true 5 1.469,0.958 1.625,1.156 0.156,0.198 10 true 4 3.042,0.948 3.198,1.146 0.156,0.198 10 true 1

Uniformly loosen and remove the 5 bolts from the camshaft housing sub-assembly, in the sequence shown in the illustration.


b.
A313944E03
0.125,0.417 0.281,0.615 0.156,0.198 10 true 1 0.135,1.563 0.292,1.76 0.156,0.198 10 true 2 0.135,0.906 0.292,1.104 0.156,0.198 10 true 3 1.177,0.021 1.365,0.188 0.188,0.167 10 true 7 1.646,0.021 1.833,0.188 0.188,0.167 10 true 10 2.146,0.021 2.333,0.188 0.188,0.167 10 true 13 2.708,0.021 2.896,0.188 0.188,0.167 10 true 4 2.906,1.219 3.094,1.385 0.188,0.167 10 true 6 2.448,1.208 2.656,1.375 0.208,0.167 10 true 15 1.927,1.208 2.135,1.375 0.208,0.167 10 true 12 1.448,1.219 1.656,1.385 0.208,0.167 10 true 9 1.156,1.979 1.365,2.146 0.208,0.167 10 true 8 1.646,1.99 1.854,2.156 0.208,0.167 10 true 11 2.146,1.99 2.354,2.156 0.208,0.167 10 true 14 2.688,1.99 2.896,2.156 0.208,0.167 10 true 5

Uniformly loosen and remove the 15 bolts from the cylinder head sub-assembly, in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



c.

Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly.

HINT:

Arrange the removed parts in the correct order.



d.
A310064

Remove the oil control valve filter from the camshaft bearing cap.


Hide 13512 12.REMOVE NO. 2 CAMSHAFT

a.
A313945

Remove the No. 2 camshaft from the camshaft housing sub-assembly.


Hide 13511 13.REMOVE CAMSHAFT

a.
A313946

Remove the camshaft from the camshaft housing sub-assembly.


Hide 13801 14.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 15.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11103 16.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A313947

Remove the 3 bolts from the camshaft housing sub-assembly.


b.
A313948C01
0.958,1.052 1.25,0.813 true 0.927,4.042 1.073,4.125 true 2.563,3.49 2.813,3.635 true 1.281,0.719 1.49,0.896 0.208,0.177 10 true *a 1.135,4.073 1.344,4.25 0.208,0.177 10 true *a 2.875,3.604 3.083,3.781 0.208,0.177 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.



Hide 13801 17.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 18.INSPECT VALVE LASH ADJUSTER ASSEMBLY