12108
1.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.
12108A
2.REMOVE OIL FILLER CAP GASKET
Remove the oil filler cap gasket from the oil filler cap sub-assembly.
19100P
3.REMOVE SPARK PLUG
11101W
4.REMOVE CAMSHAFT POSITION SENSOR
Remove the 2 bolts and 2 camshaft position sensors from the cylinder head cover sub-assembly.
If a component has been dropped or subjected to a strong impact, replace the camshaft position sensor.
11101J
5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Remove the 2 bolts and 2 camshaft timing oil control valve assemblies from the cylinder head cover sub-assembly.
If a component has been dropped or subjected to a strong impact, replace the camshaft timing oil control valve assembly.
Remove the 2 O-rings from the 2 camshaft timing oil control valve assemblies.
6.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
12204A
7.REMOVE VENTILATION SYSTEM GROMMET
Remove the ventilation system grommet from the cylinder head cover sub-assembly.
11201
8.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
| *1 | Plate Washer and Seal Washer |
Remove the 17 bolts, 2 plate washers, 2 seal washers and cylinder head cover sub-assembly from the camshaft housing sub-assembly.
Be careful not to drop any of the camshaft bearing cap oil hole gaskets into the engine when removing the cylinder head cover sub-assembly because the camshaft bearing cap oil hole gaskets may stick to the cylinder head cover sub-assembly.
Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.
Remove the 2 camshaft bearing cap oil hole gaskets from the camshaft bearing cap.
If any camshaft bearing cap oil hole gasket is missing, check that no camshaft bearing cap oil hole gaskets are stuck to the cylinder head cover sub-assembly.
11301K
9.REMOVE CRANKSHAFT POSITION SENSOR
83530
10.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89615
11.REMOVE KNOCK SENSOR
89422
12.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
16321
13.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
16326
14.REMOVE NO. 2 WATER INLET HOUSING GASKET
15.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft until its timing notch and TDC mark of the timing chain cover assembly are aligned.
| *a | Timing Mark | *b | Timing Notch |
| *c | TDC Mark | - | - |
Check that each timing mark of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are positioned as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.
13471
16.REMOVE CRANKSHAFT PULLEY
11310
17.REMOVE TIMING CHAIN COVER ASSEMBLY
Remove the 8 bolts, engine water pump assembly and water pump gasket from the timing chain cover assembly.
Remove the 3 bolts and engine mounting bracket RH from the timing chain cover assembly.
| *1 | Seal Washer |
Remove the 20 bolts and seal washer from the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the timing chain cover assembly by prying between the timing chain cover assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.
Be careful not to damage the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, cylinder block sub-assembly, and oil pan sub-assembly.
Remove the 3 oil pump O-rings from the oil pan sub-assembly.
18.REMOVE PLUG
11302A
19.REMOVE TIMING CHAIN COVER OIL SEAL
13540
20.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
13562
21.REMOVE NO. 2 CHAIN VIBRATION DAMPER
13591
22.REMOVE TIMING CHAIN TENSION ARM
13506
23.REMOVE CHAIN SUB-ASSEMBLY
13566B
24.REMOVE TIMING CHAIN GUIDE
25.REMOVE CRANKSHAFT TIMING SPROCKET
Remove the crankshaft timing sprocket from the crankshaft.
26.REMOVE CRANKSHAFT STRAIGHT PIN
Remove the crankshaft straight pin from the crankshaft.
13050
27.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Check the lock of the camshaft timing gear assembly.
Release the lock pin.
Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
| *a | Adhesive Tape Sealing Area |
| *b | Prick a Hole |
| *c | Adhesive Tape |
Clean the VVT oil hole on the intake side of the camshaft bearing cap and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)
Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.
If air leaks out, reattach adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.
The camshaft timing gear assembly may be turned in the advance direction without applying any force.
If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.
Remove the adhesive tape from the camshaft bearing cap.
| *a | Hold |
| *b | Turn |
| *c | Do not remove |
Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly from the camshaft.
Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
Be sure not to remove the other 4 bolts.
Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.
13070A
28.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
29.REMOVE CAMSHAFT BEARING CAP
13512
30.REMOVE NO. 2 CAMSHAFT
13511
31.REMOVE CAMSHAFT
13801
32.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in the correct order.
13750
33.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.
Arrange the removed parts in the correct order.
11103
34.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
11101
35.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11115
36.REMOVE CYLINDER HEAD GASKET
11445
37.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.
11401L
38.REMOVE REAR ENGINE OIL SEAL
15601
39.REMOVE OIL FILTER SUB-ASSEMBLY
40.REMOVE OIL FILTER UNION
Using a 12 mm socket hexagon wrench, remove the oil filter union from the oil pan sub-assembly.
12101A
41.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket from the oil pan sub-assembly.
12101
42.REMOVE OIL PAN SUB-ASSEMBLY
Remove the 10 bolts from the oil pan sub-assembly.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly.
Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.
Remove the oil pan O-ring from the cylinder block sub-assembly.
12122
43.REMOVE NO. 2 OIL PAN BAFFLE PLATE
Remove the 2 bolts and No. 2 oil pan baffle plate from the oil pan sub-assembly.
12121
44.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 6 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.
15104
45.REMOVE OIL STRAINER SUB-ASSEMBLY
| *a | Protective Tape |
Remove the oil strainer sub-assembly.
Using a screwdriver with its tip wrapped in protective tape, push the oil strainer sub-assembly upward as shown in the illustration.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the oil strainer sub-assembly as shown in the illustration.
If the oil strainer sub-assembly is damaged during removal, replace it with a new one.
Remove the oil strainer O-ring from the oil strainer sub-assembly.
46.REMOVE RING PIN
It is not necessary to remove the ring pins unless they are being replaced.
Remove the 10 ring pins from the camshaft housing sub-assembly.
47.REMOVE STRAIGHT PIN
It is not necessary to remove the straight pins unless they are being replaced.
Remove the 2 straight pins from the oil pan sub-assembly.