11310
1.REMOVE TIMING CHAIN COVER ASSEMBLY
13540
2.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Set the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft in the positions (20° ATDC) shown in the illustration.
| *a | Timing Mark | *b | TDC |
| *1 | Stopper Plate |
| *2 | Plunger |
| *a | Push Down |
| *b | Push |
Push down the stopper plate to release the lock and push in the plunger.
| *1 | Stopper Plate |
| *a | Pull Up |
Pull up the stopper plate with the plunger pushed to the end and lock the plunger.
| *a | Pin of 3 mm diameter |
Insert a pin of 3 mm (0.118 in.) diameter to the hole in the stopper plate.
Remove the 2 bolts and No. 1 chain tensioner assembly from the cylinder head sub-assembly.
13562
3.REMOVE NO. 2 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 2 chain vibration damper from the camshaft bearing cap.
13591
4.REMOVE TIMING CHAIN TENSION ARM
Remove the timing chain tension arm from the cylinder block sub-assembly.
13506
5.REMOVE CHAIN SUB-ASSEMBLY
Remove the chain sub-assembly from the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft.
13566B
6.REMOVE TIMING CHAIN GUIDE
Remove the 2 bolts and timing chain guide from the cylinder head sub-assembly and cylinder block sub-assembly.
13070A
7.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Check the lock of the camshaft timing exhaust gear assembly.
| *a | Adhesive Tape Sealing Area |
| *b | Prick a Hole |
| *c | Adhesive Tape |
Clean the VVT oil hole on the exhaust side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure B)
Apply approximately 200 kPa (2.0 kgf/cm2, 29 psi) of air pressure to the hole pricked in procedure B to release the lock pin.
If air leaks out, reattach adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Using a screwdriver with its tip wrapped in protective tape, forcibly turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).
Be sure to keep the camshaft timing exhaust gear assembly in the retard direction (clockwise) using a screwdriver. If the camshaft timing exhaust gear assembly is released, it will return to the most advanced position automatically due to force from the spring.
Do not damage the camshaft timing exhaust gear assembly.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times without turning it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.
Remove the adhesive tape from the camshaft bearing cap.
13050
8.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
Check the lock of the camshaft timing gear assembly.
| *a | Adhesive Tape Sealing Area |
| *b | Prick a Hole |
| *c | Adhesive Tape |
Clean the VVT oil hole on the intake side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.
Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.
Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)
Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.
If air leaks out, reattach adhesive tape.
Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.
Forcibly turn the camshaft timing gear assembly in the advance direction (counterclockwise).
Depending on the air pressure applied, the camshaft timing gear assembly may turn in the advance direction without assistance by hand.
Turn the camshaft timing gear assembly within its movable range (22 to 24°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.
Remove the adhesive tape from the camshaft bearing cap.
13070A
9.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *a | Hold |
| *b | Turn |
| *c | Do not remove |
Remove the bolt while holding the hexagonal portion of the No. 2 camshaft, then remove the camshaft timing exhaust gear assembly from the No. 2 camshaft.
Be sure not to remove the other 4 bolts.
Keep the camshaft timing exhaust gear assembly horizontal while removing it from the No. 2 camshaft.
13050
10.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Hold |
| *b | Turn |
| *c | Do not remove |
Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly from the camshaft.
Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.
Be sure not to remove the other 4 bolts.
Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.
11.REMOVE CAMSHAFT BEARING CAP
Uniformly loosen and remove the 5 bolts from the camshaft housing sub-assembly, in the sequence shown in the illustration.
Uniformly loosen and remove the 15 bolts from the cylinder head sub-assembly, in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 5 camshaft bearing caps from the camshaft housing sub-assembly.
Arrange the removed parts in the correct order.
Remove the oil control valve filter from the camshaft bearing cap.
13512
12.REMOVE NO. 2 CAMSHAFT
Remove the No. 2 camshaft from the camshaft housing sub-assembly.
13511
13.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing sub-assembly.
13801
14.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
15.REMOVE VALVE LASH ADJUSTER ASSEMBLY
11103
16.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
Remove the 3 bolts from the camshaft housing sub-assembly.
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.
13801
17.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
18.INSPECT VALVE LASH ADJUSTER ASSEMBLY