Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.04
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262437 ENGINE UNIT A

2NR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A312285

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A314370

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11101W 4.REMOVE CAMSHAFT POSITION SENSOR

a.
A312286

Remove the 2 bolts and 2 camshaft position sensors from the cylinder head cover sub-assembly.

NOTICE:

If a component has been dropped or subjected to a strong impact, replace the camshaft position sensor.



Hide 11101J 5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.
A312287

Remove the 2 bolts and 2 camshaft timing oil control valve assemblies from the cylinder head cover sub-assembly.

NOTICE:

If a component has been dropped or subjected to a strong impact, replace the camshaft timing oil control valve assembly.



b.

Remove the 2 O-rings from the 2 camshaft timing oil control valve assemblies.


Hide 6.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12204A 7.REMOVE VENTILATION SYSTEM GROMMET

a.
A312288

Remove the ventilation system grommet from the cylinder head cover sub-assembly.


Hide 11201 8.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A381479C05
1,0.656 1.583,0.74 true 1,1.531 1.583,1.448 true 1.656,0.625 1.969,0.781 0.313,0.156 10 true *1 1.656,1.333 1.969,1.49 0.313,0.156 10 true *1
*1 Plate Washer and Seal Washer


Remove the 17 bolts, 2 plate washers, 2 seal washers and cylinder head cover sub-assembly from the camshaft housing sub-assembly.

NOTICE:

Be careful not to drop any of the camshaft bearing cap oil hole gaskets into the engine when removing the cylinder head cover sub-assembly because the camshaft bearing cap oil hole gaskets may stick to the cylinder head cover sub-assembly.



b.
A381480

Remove the cylinder head cover gasket from the cylinder head cover sub-assembly.


c.
A312291

Remove the 2 camshaft bearing cap oil hole gaskets from the camshaft bearing cap.

NOTICE:

If any camshaft bearing cap oil hole gasket is missing, check that no camshaft bearing cap oil hole gaskets are stuck to the cylinder head cover sub-assembly.



Hide 11301K 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 83530 10.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 12.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 16321 13.REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 16326 14.REMOVE NO. 2 WATER INLET HOUSING GASKET

Hide 15.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Turn the crankshaft until its timing notch and TDC mark of the timing chain cover assembly are aligned.

A381450C01
4.51,0.583 3.667,0.667 3.667,0.667 4.458,0.448 true 5.573,0.5 6.24,0.5 true 1.708,1.906 2.583,2.333 true 1.646,1.802 2.083,1.25 true 3.469,0.563 3.781,0.76 0.313,0.198 10 false *a 6.323,0.417 6.635,0.615 0.313,0.198 10 false *a 4.448,0.063 4.76,0.26 0.313,0.198 10 false 1° 5.5,0.073 5.813,0.271 0.313,0.198 10 false 1° 2.646,2.281 2.958,2.479 0.313,0.198 10 false *b 2.135,1.135 2.448,1.333 0.313,0.198 10 true *c
*a Timing Mark *b Timing Notch
*c TDC Mark - -



b.

Check that each timing mark of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are positioned as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.


Hide 11310 17.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A381481

Remove the 8 bolts, engine water pump assembly and water pump gasket from the timing chain cover assembly.


b.
A312294

Remove the 3 bolts and engine mounting bracket RH from the timing chain cover assembly.


c.
A381451C01
1.823,1.75 2.74,1.417 true 2.813,1.313 3.125,1.51 0.313,0.198 10 false *1
*1 Seal Washer


Remove the 20 bolts and seal washer from the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.


d.
A200635C06
0.344,0.729 0.427,0.573 true 2.896,0.521 2.969,0.729 true 2.74,3.729 2.813,3.938 true 0.51,4.156 0.656,4.323 true 0.229,0.74 0.438,0.906 0.208,0.167 10 true *a 2.896,0.76 3.104,0.99 0.208,0.229 10 true *a 2.698,3.979 2.927,4.208 0.229,0.229 10 true *a 0.625,4.323 0.854,4.552 0.229,0.229 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the timing chain cover assembly by prying between the timing chain cover assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, cylinder block sub-assembly, and oil pan sub-assembly.



e.
A381452

Remove the 3 oil pump O-rings from the oil pan sub-assembly.


Hide 11302A 19.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 13540 20.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13562 21.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13591 22.REMOVE TIMING CHAIN TENSION ARM

Hide 13506 23.REMOVE CHAIN SUB-ASSEMBLY

Hide 13566B 24.REMOVE TIMING CHAIN GUIDE

Hide 25.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A312382

Remove the crankshaft timing sprocket from the crankshaft.


Hide 26.REMOVE CRANKSHAFT STRAIGHT PIN

a.
A313192

Remove the crankshaft straight pin from the crankshaft.


Hide 13050 27.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.


b.

Release the lock pin.

NOTICE:

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.


i.
A312295C01
0.302,3.094 1.135,1.896 true 0.958,0.583 1.76,0.583 true 1.271,0.469 1.771,0.323 true 1.813,0.229 2.125,0.385 0.313,0.156 10 false *a 1.813,0.5 2.125,0.656 0.313,0.156 10 false *b 0.135,3.031 0.448,3.188 0.313,0.156 10 false *c
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the intake side of the camshaft bearing cap and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)


iii.
A312296

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.

·

Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.



HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




iv.

Remove the adhesive tape from the camshaft bearing cap.



c.
A312383C01
0.802,2.75 0.615,2.313 0.615,2.313 0.927,2.542 true 1.177,2.896 1.656,3.156 1.656,3.156 1.01,3.115 true 1.396,0.229 1.708,0.385 0.313,0.156 10 false *a 0.615,0.656 0.927,0.813 0.313,0.156 10 false *b 0.438,2.219 0.75,2.375 0.313,0.156 10 false *c 1.698,3.083 2.01,3.24 0.313,0.156 10 false *c
*a Hold
*b Turn
*c Do not remove


Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly from the camshaft.

NOTICE:
·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.




Hide 13070A 28.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 29.REMOVE CAMSHAFT BEARING CAP

Hide 13512 30.REMOVE NO. 2 CAMSHAFT

Hide 13801 32.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A312384

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 33.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A312385

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 11103 34.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 11101 35.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 37.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A312297

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.


Hide 15601 39.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 40.REMOVE OIL FILTER UNION

a.
A243541

Using a 12 mm socket hexagon wrench, remove the oil filter union from the oil pan sub-assembly.


Hide 12101A 41.REMOVE OIL PAN DRAIN PLUG

a.
A312386

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 42.REMOVE OIL PAN SUB-ASSEMBLY

a.
A312387

Remove the 10 bolts from the oil pan sub-assembly.


b.
A312388C01
2.198,0.781 2.167,1.104 true 2.771,4.031 2.583,4.281 true 1.49,3.958 1.104,4.104 true 0.698,0.948 0.969,1.26 true 1,1.188 1.219,1.375 0.219,0.188 10 true *a 2.083,1.104 2.302,1.281 0.219,0.177 10 false *a 2.5,4.281 2.719,4.458 0.219,0.177 10 false *a 1.51,3.854 1.729,4.031 0.219,0.177 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.



c.
A312389

Remove the oil pan O-ring from the cylinder block sub-assembly.


Hide 12122 43.REMOVE NO. 2 OIL PAN BAFFLE PLATE

a.
A320642

Remove the 2 bolts and No. 2 oil pan baffle plate from the oil pan sub-assembly.


Hide 12121 44.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A320643

Remove the 6 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.


Hide 15104 45.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A243503C02
0.708,0.458 1.635,0.948 true 0.51,0.385 0.688,0.573 0.177,0.188 10 false *a
*a Protective Tape


Remove the oil strainer sub-assembly.

i.

Using a screwdriver with its tip wrapped in protective tape, push the oil strainer sub-assembly upward as shown in the illustration.


ii.
A243502C02
0.396,0.375 0.969,1.042 true 0.208,0.292 0.406,0.479 0.198,0.188 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the oil strainer sub-assembly as shown in the illustration.

NOTICE:

If the oil strainer sub-assembly is damaged during removal, replace it with a new one.



iii.
A313188

Remove the oil strainer O-ring from the oil strainer sub-assembly.



Hide 46.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A312301

Remove the 10 ring pins from the camshaft housing sub-assembly.


Hide 47.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.
A312299

Remove the 2 straight pins from the oil pan sub-assembly.