Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › CAMSHAFT › from 2016.04
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262360 CAMSHAFT A

2NR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the camshaft, No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 13750 1.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 2.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13511 3.INSTALL CAMSHAFT

a.

Clean the camshaft journals.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.
A199812

Install the camshaft to the camshaft housing sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the camshaft.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13512 4.INSTALL NO. 2 CAMSHAFT

a.

Clean the No. 2 camshaft journals.


b.

Apply a light coat of engine oil to the No. 2 camshaft journals and camshaft housing sub-assembly.


c.
A199813

Install the No. 2 camshaft to the camshaft housing sub-assembly.

HINT:

Perform "Inspection After Repair" after replacing the No. 2 camshaft.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 5.INSTALL CAMSHAFT BEARING CAP

a.

Check that no foreign matter is on the mesh part of the oil control valve filter.


b.
A314499

Install the oil control valve filter to the camshaft bearing cap.

NOTICE:

Do not touch the mesh when installing the oil control valve filter.



c.

Apply engine oil to the camshaft bearing caps.


d.
A198009E03
2,1.031 2.104,1.208 0.104,0.177 10 1 2.521,1.031 2.625,1.208 0.104,0.177 10 3 0.292,0.875 0.396,1.052 0.104,0.177 10 4 2.958,0.969 3.063,1.146 0.104,0.177 10 5 1.458,1.031 1.563,1.208 0.104,0.177 10 2

Temporarily tighten the 5 camshaft bearing caps to the camshaft housing sub-assembly.


e.

Fully tighten the 5 bolts in the sequence shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 11103 6.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A321815C01
0.771,1.281 1.021,1.281 false 1.333,0.333 1.583,0.5 false 2.063,0.792 2.25,0.573 true 2.021,0.917 2.521,1.25 true 1.135,0.25 1.448,0.406 0.313,0.156 10 false *1 0.563,1.198 0.875,1.354 0.313,0.156 10 false *2 2.583,1.177 2.896,1.333 0.313,0.156 10 false *3 2.313,0.49 2.625,0.646 0.313,0.156 10 false *4
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve
*4 Valve Stem Cap


Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A384957C04
2.417,1.979 2.417,1.646 false 1.167,2.75 1.677,2.469 1.677,2.469 1.552,2.719 true 1.604,2.885 1.865,3.052 false 2.354,2 2.667,2.156 0.313,0.156 10 false *a 1.719,2.375 2.031,2.531 0.313,0.156 10 false *b 1.885,3.01 2.198,3.167 0.313,0.156 10 false *a
*a Seal Packing
*b Oil Line


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


NOTICE:
·

Prevent Seal Packing from entering the oil passages.

·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A313952C01
1.844,0.958 2.229,0.271 true 2.729,1.448 2.948,1.615 0.219,0.167 10 true *a 2.302,0.177 2.5,0.333 0.198,0.156 10 true *b 2.708,1.188 3.021,1.385 0.313,0.198 10 true 23° 2.708,0.792 3.021,0.99 0.313,0.198 10 true 17°
*a TDC
*b Timing Mark


Set the crankshaft in the position (40° BTDC) shown in the illustration.

NOTICE:

Turn the crankshaft clockwise when positioning the No. 1 cylinder after the camshaft housing sub-assembly is installed.


HINT:

Make sure that the timing mark of the crankshaft is positioned as shown in the illustration.



d.

Set the camshaft and No. 2 camshaft as shown in the illustration.

A297424C09
1.802,1.792 2.177,1.458 true 1.396,1.427 1.656,1.656 true 1.344,2.417 1.542,2.188 true 5.51,1.667 5.813,1.354 true 5.021,1.406 5.354,1.781 true 5.802,2.344 5.635,2.146 true 2.229,1.333 2.521,1.563 0.292,0.229 10 false *1 1.188,1.323 1.458,1.521 0.271,0.198 10 false *2 5.865,1.229 6.146,1.479 0.281,0.25 10 false *3 1.156,2.365 1.438,2.604 0.281,0.24 10 false *a 4.823,1.292 5.115,1.521 0.292,0.229 10 false *1 5.865,2.323 6.146,2.563 0.281,0.24 10 false *a 3.458,2.177 3.948,2.354 0.49,0.177 10 false 13 (A) 3,0 3.521,0.156 0.521,0.156 10 false 17 (A) 2.615,0.302 3.125,0.448 0.51,0.146 10 false 12 (A) 4.167,1.615 4.604,1.771 0.438,0.156 10 false 18 (B) 4.167,1.365 4.531,1.521 0.365,0.156 10 false 8 (A) 3.781,0 4.219,0.156 0.438,0.156 10 false 16 (A) 2.677,0.656 3.063,0.813 0.385,0.156 10 false 3 (A) 2.677,0.99 3.094,1.135 0.417,0.146 10 false 6 (A) 2.677,1.313 3.063,1.469 0.385,0.156 10 false 9 (A) 2.625,1.844 3.031,2.01 0.406,0.167 10 true 15 (A) 4.146,1.958 4.542,2.125 0.396,0.167 10 true 14 (A) 4.156,1.021 4.5,1.177 0.344,0.156 10 false 5 (A) 4.146,0.667 4.49,0.823 0.344,0.156 10 false 2 (A) 4.198,0.354 4.594,0.5 0.396,0.146 10 false 11 (A) 3.563,1.729 3.896,1.896 0.333,0.167 10 true 7 (A) 3.677,1.302 4.01,1.469 0.333,0.167 10 true 4 (A) 3.677,0.958 4,1.115 0.323,0.156 10 true 1 (A) 3.688,0.615 4.094,0.771 0.406,0.156 10 true 10 (A)
*1 Straight Pin *2 Camshaft
*3 No. 2 Camshaft - -
*a No. 1 Cylinder Cam - -


HINT:

Make sure that the straight pin of the camshaft is positioned as shown in the illustration.



e.

Install the camshaft housing sub-assembly to the cylinder head sub-assembly with the 18 bolts, in the sequence shown in the illustration.

Bolt Length:
Item Length
Bolt A 70 mm (2.756 in.)
Bolt B 35 mm (1.378 in.)


Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

After installing the camshaft housing sub-assembly, make sure that the straight pin is positioned as shown in the illustration.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head sub-assembly.




Hide 13050 7.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check that the straight pin is installed on the camshaft.


b.
A198838C19
2.115,1.021 2.521,0.344 true 0.698,1.021 1.292,0.344 true 2.573,0.24 2.75,0.396 0.177,0.156 10 false *1 1.344,0.24 1.521,0.396 0.177,0.156 10 false *a
*1 Straight Pin
*a Straight Pin Hole


Fit the camshaft timing gear assembly and camshaft together by aligning the straight pin hole and straight pin.

NOTICE:
·

Do not forcefully push in the camshaft timing gear assembly. This may cause the straight pin tip to damage the installation surface of the camshaft timing gear assembly.

·

Do not turn the camshaft timing gear assembly in the retard direction (clockwise).




c.

Temporarily tighten the camshaft timing gear assembly to the camshaft with the bolt.


d.
A313949C01
1.417,0.031 1.729,0.188 0.313,0.156 10 false *a 0.729,0.365 1.042,0.521 0.313,0.156 10 false *b
*a Hold
*b Turn


Fully tighten the bolt while holding the hexagonal portion of the camshaft.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.
A313950C01
0.594,0.344 0.781,0.521 0.188,0.177 10 true *a
*a Lock


Check that the camshaft timing gear assembly moves in the retard direction (clockwise) and locks in the most retarded position.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13070A 8.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check that the straight pin is installed on the No. 2 camshaft.


b.
A198839C17
1.469,0.323 0.802,0.99 true 2.531,0.323 2.198,0.979 true 2.573,0.219 2.75,0.385 0.177,0.167 10 false *1 1.531,0.229 1.708,0.396 0.177,0.167 10 false *a
*1 Straight Pin
*a Straight Pin Hole


Fit the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the straight pin hole and straight pin.

NOTICE:

Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.



c.

Temporarily tighten the camshaft timing exhaust gear assembly to the No. 2 camshaft with the bolt.


d.
A305915C01
1.646,0.021 1.958,0.177 0.313,0.156 10 false *a 0.708,0.25 1.021,0.406 0.313,0.156 10 false *b
*a Hold
*b Turn


Fully tighten the bolt while holding the hexagonal portion of the No. 2 camshaft.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.

Make sure that the camshaft timing exhaust gear assembly is locked.

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 13566B 9.INSTALL TIMING CHAIN GUIDE

a.

Install the timing chain guide to the cylinder head sub-assembly and cylinder block sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13506 10.INSTALL CHAIN SUB-ASSEMBLY

a.
A313951C01
0.917,1.656 1.51,1.25 true 2.729,1.427 2.917,1.594 0.188,0.167 10 true *b 0.729,1.615 0.969,1.781 0.24,0.167 10 true *a 2.708,1.188 3.031,1.365 0.323,0.177 10 true 23° 2.146,1.917 2.469,2.094 0.323,0.177 10 true 90°
*a Timing Mark
*b TDC


Set the crankshaft in the position (90° ATDC) shown in the illustration.

HINT:

Make sure that the timing mark of the crankshaft is positioned as shown in the illustration.



b.

Set the camshaft timing gear assembly in the positions (24° ATDC) shown in the illustration.

A313959C01
3.313,0.583 3.458,0.573 3.458,0.573 3.26,0.708 true 3.271,0.646 3.448,0.583 true 4.021,0.573 3.813,0.531 3.813,0.531 4.031,0.635 true 1.542,4.063 1.771,3.771 true 2.24,3.875 2.552,4.031 0.313,0.156 10 false *b 3.219,0.219 3.5,0.417 0.281,0.198 10 false 24° 3.958,0.219 4.24,0.417 0.281,0.198 10 false 12° 3.646,0.438 3.802,0.604 0.156,0.167 10 true *a 2.188,3.698 2.469,3.865 0.281,0.167 10 false 23° 2.104,4.052 2.385,4.219 0.281,0.167 10 false 20° 3.479,0.5 3.688,0.656 0.208,0.156 10 true *a 1.427,4.073 1.635,4.229 0.208,0.156 10 true *a
*a Timing Mark *b TDC



c.

Set the camshaft timing exhaust gear assembly in the positions (12° BTDC) shown in the illustration.


d.

Set the crankshaft in the position (20° ATDC) shown in the illustration.


e.

Align the timing marks of the camshaft timing gear assembly, camshaft timing exhaust gear assembly and crankshaft with the mark plates of the chain sub-assembly and install the chain sub-assembly.

A313960C01
3.792,0.344 3.969,0.615 true 3.969,0.667 4.219,0.667 4.219,0.667 3.906,0.792 true 3.948,0.719 4.198,0.667 true 5.083,0.375 4.938,0.573 true 4.927,0.625 4.667,0.667 4.667,0.667 4.938,0.688 true 2.417,4.01 2.177,3.729 true 1.833,4.073 1.938,3.688 true 3.604,0.281 3.771,0.438 0.167,0.156 10 false *a 2.344,4.052 2.521,4.229 0.177,0.177 10 true *b 1.74,4.094 1.917,4.26 0.177,0.167 10 true *c 4.24,0.563 4.417,0.708 0.177,0.146 10 true *c 5.135,0.271 5.302,0.427 0.167,0.156 10 false *a 4.5,0.583 4.677,0.729 0.177,0.146 10 true *c
*a Mark Plate (Yellow) *b Mark Plate (Orange)
*c Timing Mark - -



Hide 13591 11.INSTALL TIMING CHAIN TENSION ARM

a.

Install the timing chain tension arm to the cylinder block sub-assembly.


Hide 13540 12.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.

Install the No. 1 chain tensioner assembly to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the No. 2 chain vibration damper to the camshaft bearing cap with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Remove the pin of 3 mm (0.118 in.) diameter from the No. 1 chain tensioner assembly.


d.

Turn the crankshaft approximately 20° counterclockwise to set it to TDC. Make sure that the timing marks and mark plates are correctly positioned and that the chain sub-assembly is securely fit into the timing chain tension arm, timing chain guide and No. 2 chain vibration damper.

A314454C01
3.104,0.594 3.354,0.552 3.354,0.552 3.104,0.729 true 3.104,0.646 3.344,0.552 true 4.115,0.594 4.385,0.563 4.385,0.563 4.115,0.656 true 2.938,0.417 3.083,0.563 true 3.885,0.417 4.063,0.573 true 1.479,4.125 1.677,3.729 true 1.75,3.708 2.063,3.417 true 2.083,3.854 2.396,4.01 0.313,0.156 10 false *a 3.667,4.573 3.865,4.74 0.198,0.167 10 true *b 2.083,3.302 2.396,3.458 0.313,0.156 10 false *d 3.396,0.469 3.708,0.625 0.313,0.156 10 true *e 3.063,0.229 3.375,0.427 0.313,0.198 10 false 1° 4.094,0.229 4.406,0.427 0.313,0.198 10 false 1° 2.135,3.698 2.448,3.896 0.313,0.198 10 false 23° 2.021,4.021 2.333,4.219 0.313,0.198 10 false 20° 4.438,0.479 4.75,0.635 0.313,0.156 10 true *e 2.781,0.302 3.094,0.458 0.313,0.156 10 false *c 3.729,0.323 4.042,0.479 0.313,0.156 10 false *c 1.385,4.156 1.698,4.313 0.313,0.156 10 true *e
*a TDC *b Turn
*c Mark Plate (Yellow) *d Mark Plate (Orange)
*e Timing Mark - -



Hide 11310 13.INSTALL TIMING CHAIN COVER ASSEMBLY