Perform "Inspection After Repair" after replacing the camshaft or No. 2 camshaft or camshaft timing gear assembly or camshaft timing exhaust gear assembly or engine coolant temperature sensor or knock sensor or spark plug.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
1.INSTALL STRAIGHT PIN
It is not necessary to remove the straight pins unless they are being replaced.
Using a plastic hammer, tap in 2 new straight pins to the specified protrusion height.
8.0 to 10.0 mm (0.315 to 0.394 in.)
2.INSTALL RING PIN
It is not necessary to remove the ring pins unless they are being replaced.
Using a plastic hammer, tap in 10 new ring pins to the specified protrusion height.
2.7 to 3.3 mm (0.106 to 0.130 in.)
15104
3.INSTALL OIL STRAINER SUB-ASSEMBLY
Apply a light coat of engine oil to a new oil strainer O-ring.
Install the oil strainer O-ring to the oil strainer sub-assembly.
Do not twist the oil strainer O-ring.
Install the oil strainer sub-assembly to the oil pan sub-assembly.
Do not twist the oil strainer O-ring.
12121
4.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Install the No. 1 oil pan baffle plate to the oil pan sub-assembly with the 6 bolts.
12122
5.INSTALL NO. 2 OIL PAN BAFFLE PLATE
Install the No. 2 oil pan baffle plate to the oil pan sub-assembly with the 2 bolts.
12101
6.INSTALL OIL PAN SUB-ASSEMBLY
Remove any old packing material from the contact surface.
Install a new oil pan O-ring to the cylinder block sub-assembly.
Apply seal packing to the places shown in the illustration.
| *a | Continuous Line Area | *b | Dashed Line Area |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
Clean and degrease the threads of the bolt (C) and threaded portion of the cylinder block sub-assembly.
| *a | Adhesive |
Apply adhesive to the threads of the bolt (C).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Apply adhesive to the bolt (C) more than 7.0 mm (0.276 in.) from the bolt end.
| *a | Temporarily Tighten |
Install the oil pan sub-assembly to the cylinder block sub-assembly with the 10 bolts, in the sequence shown in the illustration.
| Item | Length |
|---|---|
| Bolt A | 70 mm (2.756 in.) |
| Bolt B, C | 30 mm (1.181 in.) |
Wipe off any excess seal packing with a clean piece of cloth.
12101A
7.INSTALL OIL PAN DRAIN PLUG
Install a new gasket and oil pan drain plug to the oil pan sub-assembly.
8.INSTALL OIL FILTER UNION
Using a 12 mm socket hexagon wrench, install the oil filter union to the oil pan sub-assembly.
15601
9.INSTALL OIL FILTER SUB-ASSEMBLY
11401L
10.INSTALL REAR ENGINE OIL SEAL
11445
11.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the cylinder block water jacket spacer to the cylinder block sub-assembly.
11115
12.INSTALL CYLINDER HEAD GASKET
11101
13.INSTALL CYLINDER HEAD SUB-ASSEMBLY
13750
14.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Keep the valve lash adjuster assembly free of dirt and foreign matter.
Only use clean engine oil.
Place the valve lash adjuster assembly into a container filled with engine oil.
| *1 | Plunger |
| *2 | Check Ball |
| *a | Correct |
| *b | Incorrect |
| *c | Taper Part |
| *d | Low Pressure Chamber |
| *e | High Pressure Chamber |
Insert the tip of SST into the valve lash adjuster assembly plunger and use the tip to press down on the check ball inside the plunger.
Squeeze SST and valve lash adjuster assembly together to move the plunger up and down 5 to 6 times.
Check the movement of the plunger and bleed it.
Plunger moves up and down.
When bleeding the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, the high-pressure chamber will not be bled.
After bleeding, remove SST. Then, try to press the plunger quickly and firmly by hand.
Plunger is very difficult to move.
If the result is not as specified, replace the valve lash adjuster assembly.
Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.
Install each valve lash adjuster assembly to the same place it was removed from.
13801
15.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Apply engine oil to the valve lash adjuster assembly tip and valve stem cap end.
| *1 | No. 1 Valve Rocker Arm Sub-assembly |
| *2 | Valve Lash Adjuster Assembly |
| *3 | Valve |
| *4 | Valve Stem Cap |
Make sure that the 16 No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.
Fill the cylinder head sub-assembly with engine oil through the holes indicated in the illustration.
13511
16.INSTALL CAMSHAFT
13512
17.INSTALL NO. 2 CAMSHAFT
18.INSTALL CAMSHAFT BEARING CAP
11103
19.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY
13070A
20.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13050
21.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
22.INSTALL CRANKSHAFT STRAIGHT PIN
Install the crankshaft straight pin into the crankshaft groove.
23.INSTALL CRANKSHAFT TIMING SPROCKET
| *a | Groove |
Align the groove of the crankshaft timing sprocket with the key of the crankshaft and install the crankshaft timing sprocket.
13566B
24.INSTALL TIMING CHAIN GUIDE
13506
25.INSTALL CHAIN SUB-ASSEMBLY
13591
26.INSTALL TIMING CHAIN TENSION ARM
13540
27.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
11302A
28.INSTALL TIMING CHAIN COVER OIL SEAL
29.INSTALL PLUG
11310
30.INSTALL TIMING CHAIN COVER ASSEMBLY
Remove any old seal packing material from the contact surface.
Temporarily install a new water pump gasket and engine water pump assembly to the timing chain cover assembly with the 4 bolts.
20 mm (0.787 in.)
Clean the contact surfaces of the timing chain cover assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.
|
Surface to be cleaned | - | - |
Install 3 new oil pump O-rings to the oil pan sub-assembly.
Apply seal packing to the timing chain cover assembly as shown in the following illustration.
| *a | Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent | *b | Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent |
If there is oil on the contact surfaces, wipe them with oil-free cloth before applying seal packing.
Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after installation.
Areas A-A and B-B are the joints between the cylinder block sub-assembly and oil pan sub-assembly, cylinder block sub-assembly and cylinder head sub-assembly, and cylinder head sub-assembly and camshaft housing sub-assembly.
| Area | Seal Packing Diameter | Seal packing |
|---|---|---|
| Continuous Line Area
Except A-A and B-B |
3.5 to 4.5 mm (0.138 to 0.177 in.) | Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent |
| Dashed Line Area | 3.5 to 4.5 mm (0138 to 0.177 in.) | Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent |
Align the oil pump drive rotor spline and crankshaft as shown in the illustration, and install the timing chain cover assembly to the crankshaft.
| *1 | Seal Washer |
Temporarily install the 24 bolts and a new seal washer.
| Item | Length |
|---|---|
| Bolt A | 40 mm (1.575 in.) |
| Bolt B | 50 mm (1.969 in.) |
| Bolt C, D | 25 mm (0.984 in.) |
| Bolt E | 35 mm (1.378 in.) |
| *a | Adhesive |
Clean and degrease the threads of the bolt (D) and threaded hole of the cylinder block sub-assembly.
Apply adhesive to the bolt (D) more than 7.0 mm (0.276 in.) from the bolt tip.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Temporarily install the engine mounting bracket RH to the timing chain cover assembly with the 3 bolts.
| Item | Length |
|---|---|
| Bolt A | 40 mm (1.57 in.) |
| Bolt F | 80 mm (3.15 in.) |
Fully tighten the 27 bolts in the sequence shown in the illustration.
Fully tighten the 4 bolts.
13471
31.INSTALL CRANKSHAFT PULLEY
16326
32.INSTALL NO. 2 WATER INLET HOUSING GASKET
16321
33.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
89422
34.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
89615
35.INSTALL KNOCK SENSOR
83530
36.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY
11301K
37.INSTALL CRANKSHAFT POSITION SENSOR
11201
38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.
Remove any oil from the contact surfaces.
Check that no camshaft bearing cap oil hole gaskets are stuck to the cylinder head cover sub-assembly.
Install 2 new camshaft bearing cap oil hole gaskets to the camshaft bearing cap.
Remove any old packing material from the contact surface.
| *a | Seal Diameter 2.0 mm |
Apply seal packing as shown the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 mm (0.0787 in.)
Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
Do not start the engine for at least 2 hours after the installation.
| *1 | Plate Washer and Seal Washer |
Temporarily install the cylinder head cover sub-assembly with the 2 plate washers and 2 new seal washers to the camshaft housing sub-assembly with the 17 bolts.
| Item | Length |
|---|---|
| Bolt A | 23.5 mm (0.925 in.) |
| Bolt B | 35 mm (1.378 in.) |
Apply a light coat of engine oil to the 2 O-rings of the 2 camshaft position sensors.
If reusing the camshaft position sensor, be sure to inspect the O-ring.
Temporarily install the 2 camshaft position sensors to the cylinder head cover sub-assembly with the 2 bolts.
If a component has been dropped or subjected to a strong impact, replace the camshaft position sensor.
Make sure that the O-ring is not damaged or does not jump out of position during installation.
Fully tighten the 19 bolts in the sequence shown in the illustration.
12204A
39.INSTALL VENTILATION SYSTEM GROMMET
Install the ventilation system grommet to the cylinder head cover sub-assembly.
12204
40.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
11101J
41.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to 2 new O-rings, then install them onto the 2 camshaft timing oil control valve assemblies.
Do not twist the O-ring.
Install the 2 camshaft timing oil control valve assemblies to the cylinder head cover sub-assembly with the 2 bolts.
If a component has been dropped or subjected to a strong impact, replace the camshaft timing oil control valve assembly.
Make sure that the O-ring is not damaged or does not jump out of position during installation.
19100P
42.INSTALL SPARK PLUG
12108A
43.INSTALL OIL FILLER CAP GASKET
Install a new oil filler cap gasket to the oil filler cap sub-assembly.
12108
44.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.