Home › Engine / Hybrid System › 2NR-FE LUBRICATION › OIL PUMP › from 2016.04
RM30M0E _51 Engine / Hybrid System _054017 2NR-FE LUBRICATION _0262599 OIL PUMP A

2NR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11302A 1.INSTALL TIMING CHAIN COVER OIL SEAL

a.
A197956E05
1.823,1.688 2.042,1.521 2.042,1.521 1.938,2.042 true 2.094,1.438 2.406,1.625 0.313,0.188 10 false SST 0.104,1.469 0.417,1.656 0.313,0.188 10 false + 0.104,1.292 0.417,1.479 0.313,0.188 10 false -

Using SST and a hammer, tap in a new timing chain cover oil seal until its surface is flush with the timing chain cover assembly edge.

SST
09950-60010  (09951-00330, 09951-00480, 09952-06010)
09950-70010  (09951-07100)

NOTICE:

Do not tap the timing chain cover oil seal at an angle.


Timing chain cover oil seal tap in depth:

-0.5 to 1.0 mm (-0.0197 to 0.0393 in.)



b.

Apply a light coat of MP grease to the timing chain cover oil seal lip.

NOTICE:

Keep the timing chain cover oil seal lip free of foreign matter.



Hide 2.INSTALL PLUG

a.

Clean and degrease the threads of the plug and threaded hole of the timing chain cover assembly.


b.
A201138C20
1.583,1.167 2.396,1.469 true 2.458,1.417 3.083,1.594 0.625,0.177 10 false *a
*a Adhesive


Apply adhesive to the plug more than 3.0 mm (0.118 in.) from the plug tip.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Using an 8 mm socket hexagon wrench, install the plug to the timing chain cover assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



Hide 11310 3.INSTALL TIMING CHAIN COVER ASSEMBLY

a.

Remove any remaining seal packing material.


b.

Clean the contact surfaces of the timing chain cover assembly, camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly, and confirm that no oil, moisture or other foreign matter is on the surfaces.

A381454C02
0,0 0,0 false
V100145

Surface to be Cleaned - -



c.

Install 3 new oil pump O-rings to the oil pan sub-assembly.


d.

Apply seal packing to the timing chain cover assembly as shown in the illustration.

A381455C01
2.51,1.073 3.625,0.219 3.625,0.219 3.281,1.635 true 1.865,2.802 2.781,2.802 true 3.49,1.729 4.25,0.333 true 2.24,1.583 2.396,1.781 0.156,0.198 10 false A 3.177,2.323 3.333,2.521 0.156,0.198 10 true B 4.375,1.646 4.531,1.844 0.156,0.198 10 true A 5,1.448 5.156,1.646 0.156,0.198 10 false A 5.583,1.26 6.24,1.677 0.656,0.417 10 false 17.5 mm 6.333,1.438 6.99,1.854 0.656,0.417 10 false 323.5 mm 4.313,0.229 5.646,0.479 1.333,0.25 10 false 19.5 mm (0.768 in.) 3.698,0.073 3.938,0.271 0.24,0.198 10 false *a 2.563,2.573 2.719,2.771 0.156,0.198 10 true B 3.833,2.469 3.99,2.667 0.156,0.198 10 true B 4.479,2.458 4.635,2.656 0.156,0.198 10 false B 5.583,2.167 6.229,2.594 0.646,0.427 10 false 12.0 mm 6.354,3.063 7.01,3.479 0.656,0.417 10 false 221.0 mm 6.438,4.167 7.104,4.583 0.667,0.417 10 false 17.0 mm 1.667,2.708 1.906,2.906 0.24,0.198 10 false *b 1.125,1.198 1.781,1.615 0.656,0.417 10 false 23.0 mm 0.219,1.417 0.875,1.833 0.656,0.417 10 false 328.5 mm 1.156,2.177 1.813,2.594 0.656,0.417 10 false 18.5 mm 0.208,3.042 0.865,3.458 0.656,0.417 10 false 225.5 mm 1.042,4.396 1.698,4.813 0.656,0.417 10 false 14.0 mm 0.229,4.156 0.885,4.573 0.656,0.417 10 false 18.0 mm 2.219,4.375 2.375,4.573 0.156,0.198 10 false A 2.875,1.438 3.031,1.635 0.156,0.198 10 false A 2.823,4.563 2.979,4.76 0.156,0.198 10 true A 4.219,4.417 4.375,4.615 0.156,0.198 10 true A 4.875,4.521 5.031,4.719 0.156,0.198 10 false A 5.563,4.365 6.188,4.76 0.625,0.396 10 false 12.0 mm 0.385,5.188 0.729,5.438 0.344,0.25 10 false A-A 3.885,5.208 4.229,5.458 0.344,0.25 10 false B-B 0.792,5.604 2.948,5.802 2.156,0.198 10 false (0.157 to 0.315 in.) 0.813,5.438 2.969,5.635 2.156,0.198 10 false 4.0 to 8.0 mm 4.25,5.417 6.406,5.615 2.156,0.198 10 false 13.0 to 15.0 mm 4.26,5.583 5.479,5.771 1.219,0.188 10 false (0.512 to 0.591 in.) 5.844,6.49 6.969,6.667 1.125,0.177 10 false 3.5 to 4.5 mm 5.833,6.667 7.052,6.854 1.219,0.188 10 false (0138 to 0.177 in.) 1.948,6.396 3.073,6.573 1.125,0.177 10 false 3.5 to 4.5 mm 1.938,6.583 3.156,6.771 1.219,0.188 10 false (0138 to 0.177 in.) 0.354,6.063 1.563,6.25 1.208,0.188 10 false 3.5 mm 0.333,6.229 1.552,6.438 1.219,0.208 10 false (0.138 in.) 3.552,6.167 4.76,6.354 1.208,0.188 10 false 7.0 mm 3.542,6.333 4.76,6.542 1.219,0.208 10 false (0.276 in.) 5.594,1.417 6.25,1.833 0.656,0.417 10 false (0.689 in.) 5.583,2.323 6.229,2.75 0.646,0.427 10 false (0.472 in.) 1.104,1.365 1.76,1.781 0.656,0.417 10 false (0.906 in.) 1.156,2.344 1.813,2.76 0.656,0.417 10 false (0.728 in.) 6.344,1.594 7,2.01 0.656,0.417 10 false (1.061 ft.) 6.354,3.24 7.01,3.656 0.656,0.417 10 false (8.701 in.) 6.438,4.333 7.104,4.75 0.667,0.417 10 false (0.669 in.) 5.573,4.521 6.198,4.917 0.625,0.396 10 false (0.472 in.) 1.031,4.552 1.688,4.969 0.656,0.417 10 false (0.551 in.) 0.198,1.583 0.854,2 0.656,0.417 10 false (1.077 ft.) 0.198,3.198 0.854,3.615 0.656,0.417 10 false (8.878 in.) 0.229,4.323 0.885,4.74 0.656,0.417 10 false (0.709 in.)
*a Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent *b Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

If there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.



HINT:

Areas A-A and B-B are the joints between the cylinder block sub-assembly and oil pan sub-assembly, the cylinder block sub-assembly and cylinder head sub-assembly, and the cylinder head sub-assembly and camshaft housing sub-assembly.


Application Specification:
Area Seal Packing Diameter Seal packing
Continuous Line Area
Except A-A and B-B
3.5 to 4.5 mm (0.138 to 0.177 in.) Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Dashed Line Area 3.5 to 4.5 mm (0.138 to 0.177 in.) Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent



e.

Align the oil pump drive rotor spline and crankshaft as shown in the illustration and install the timing chain cover assembly to the crankshaft.

A381456


f.

Clean and degrease the threads of the bolts and threaded holes of the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly and oil pan sub-assembly.


g.
A300629C01
1.667,1.448 1.51,0.813 true 1.323,0.708 1.635,0.865 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the bolt (D) more than 7.0 mm (0.276 in.) from the bolt tip.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



h.
A381457C03
1.729,1.594 1.75,1.74 true 0.792,0.188 0.948,0.385 0.156,0.198 10 false C 0.792,0.365 0.948,0.563 0.156,0.198 10 false C 0.844,1.302 1,1.5 0.156,0.198 10 false C 0.688,1.792 0.844,1.99 0.156,0.198 10 true C 0.521,2.208 0.677,2.396 0.156,0.188 10 false C 0.677,2.74 0.833,2.927 0.156,0.188 10 false C 1.333,3.083 1.479,3.25 0.146,0.167 10 true C 2.302,2.969 2.448,3.188 0.146,0.219 10 false C 2.448,2.719 2.604,2.906 0.156,0.188 10 false C 1.625,3.26 1.771,3.427 0.146,0.167 10 true C 2.906,0.552 3.063,0.74 0.156,0.188 10 false C 2.969,0.375 3.125,0.563 0.156,0.188 10 false A 2.833,0.729 2.99,0.917 0.156,0.188 10 false B 2.906,0.552 3.063,0.74 0.156,0.188 10 false C 2.667,1.417 2.823,1.604 0.156,0.188 10 false A 2.646,1.031 2.802,1.219 0.156,0.188 10 false B 2.563,1.208 2.719,1.396 0.156,0.188 10 false B 1.719,1.208 1.865,1.375 0.146,0.167 10 true A 1.667,0.677 1.813,0.844 0.146,0.167 10 true B 1.396,1.906 1.5,2.083 0.104,0.177 10 true E 1.583,2.208 1.729,2.375 0.146,0.167 10 true A 1.708,2.51 1.854,2.677 0.146,0.167 10 true A 0.729,0.854 0.885,1.042 0.156,0.188 10 false A 0.906,1.094 1.063,1.281 0.156,0.188 10 false B 0.552,2.021 0.698,2.188 0.146,0.167 10 true D 1.552,1.521 1.74,1.719 0.188,0.198 10 false *1
*1 Seal Washer


Temporarily install the 24 bolts and a new seal washer.

Bolt Length:
Item Length
Bolt A 40 mm (1.575 in.)
Bolt B 50 mm (1.969 in.)
Bolt C, D 25 mm (0.984 in.)
Bolt E 35 mm (1.378 in.)



i.
A312261E01
0.948,0.156 1.104,0.333 0.156,0.177 10 true F 3.177,1.198 3.344,1.417 0.167,0.219 10 true F 1.292,1.885 1.458,2.125 0.167,0.24 10 true A

Temporarily install the engine mounting bracket RH to the timing chain cover assembly with the 3 bolts.

Bolt Length:
Item Length
Bolt A 40 mm (1.57 in.)
Bolt F 80 mm (3.15 in.)



j.
A381458E02
0.25,0.365 0.688,0.563 0.438,0.198 10 false 24 (C) 0.281,0.583 0.719,0.781 0.438,0.198 10 false 23 (C) 0.219,0.833 0.656,1.031 0.438,0.198 10 false 7 (F) 0.25,1.219 0.688,1.417 0.438,0.198 10 false 22 (A) 0.51,1.521 0.948,1.719 0.438,0.198 10 false 2 (B) 0.479,1.885 0.917,2.083 0.438,0.198 10 false 6 (A) 0.302,2.125 0.74,2.323 0.438,0.198 10 false 9 (C) 0.156,2.479 0.552,2.688 0.396,0.208 10 true 10 (C) 0,2.844 0.438,3.042 0.438,0.198 10 true 11 (D) 0.01,3.135 0.417,3.354 0.406,0.219 10 false 12 (C) 0.052,3.615 0.469,3.833 0.417,0.219 10 false 13 (C) 0.542,3.865 0.958,4.094 0.417,0.229 10 true 14 (C) 1.365,4.302 1.781,4.521 0.417,0.219 10 true 15 (C) 2.313,3.896 2.74,4.104 0.427,0.208 10 false 16 (C) 2.531,3.552 3,3.781 0.469,0.229 10 false 17 (C) 2.729,1.938 3.156,2.156 0.427,0.219 10 false 21 (A) 2.604,1.677 3.042,1.875 0.438,0.198 10 false 1 (B) 2.708,1.469 3.146,1.667 0.438,0.198 10 false 3 (B) 2.938,1.135 3.375,1.333 0.438,0.198 10 false 5 (B) 3,0.823 3.406,1.031 0.406,0.208 10 false 25 (C) 2.875,0.292 3.281,0.5 0.406,0.208 10 false 26 (A) 1.854,0.74 2.25,0.927 0.396,0.188 10 true 8 (F) 1.396,0.99 1.792,1.177 0.396,0.188 10 true 4 (B) 1.594,1.771 1.99,1.958 0.396,0.188 10 true 20 (A) 1.25,2.667 1.646,2.854 0.396,0.188 10 true 27 (E) 1.51,2.938 1.906,3.125 0.396,0.188 10 true 19 (A) 1.542,3.344 1.938,3.531 0.396,0.188 10 true 18 (A)

Fully tighten the 27 bolts in the sequence shown in the illustration.

Torque:
Bolt A, C and D : 24 N*m (245 kgf*cm, 18 ft.*lbf)
Bolt B : 60.5 N*m (617 kgf*cm, 45 ft.*lbf)
Bolt E : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt F : 71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 11301K 5.INSTALL CRANKSHAFT POSITION SENSOR

Hide 16326 6.INSTALL NO. 2 WATER INLET HOUSING GASKET

Hide 16321 7.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 11201 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16620 9.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16268 10.CONNECT NO. 1 WATER BY-PASS PIPE

Hide 17168 11.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 12262 12.INSTALL NO. 2 VENTILATION HOSE