Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for LHD) › 2016.04–2016.10
RM30M0E _54 Brake _017099 BRAKE SYSTEM (OTHER) _0092757 BRAKE MASTER CYLINDER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 47201 1.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)

a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
C358036C01
1.813,2.99 2.125,3.146 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




d.

Connect the brake fluid level warning switch connector.


e.

Engage the wire harness clamp.


f.

for 1NR-FE, 2NR-FE:

i.

Engage the wire harness clamp.



g.
C358029C02
1.75,2.958 2.063,3.115 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.
C358037C01
1.698,2.917 2.01,3.073 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ VSC)

a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
C358036C01
1.813,2.99 2.125,3.146 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 12 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




d.

Connect the brake fluid level warning switch connector.


e.

Engage the wire harness clamp.


f.

for 1NR-FE, 2NR-FE:

i.

Engage the wire harness clamp.



g.
C359222C01
1.75,3 2.063,3.156 0.313,0.156 10 false *a 0.906,0.635 1.156,0.854 0.25,0.219 10 false (B) 1.583,0.083 1.833,0.302 0.25,0.219 10 true (A) 1.958,0.177 2.208,0.396 0.25,0.219 10 false (A) 2.302,0.448 2.552,0.667 0.25,0.219 10 true (A) 2.042,0.844 2.292,1.063 0.25,0.219 10 true (B) 1.042,0.375 1.292,0.594 0.25,0.219 10 false (A)
*a Torque Wrench Fulcrum Length


Using a 10 mm and 12 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




h.
C358037C01
1.698,2.917 2.01,3.073 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 47201 3.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/o ABS,VSC)

a.

Install a new O-ring to the brake master cylinder sub-assembly.


b.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.
C358036C01
1.813,2.99 2.125,3.146 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




d.

Connect the brake fluid level warning switch connector.


e.

Engage the wire harness clamp.


f.

for 1NR-FE, 2NR-FE:

i.

Engage the wire harness clamp.



g.
C358040C01
1.729,2.917 2.042,3.073 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 6 brake tubes to the proportioning valve assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.
C358037C01
1.698,2.917 2.01,3.073 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the front No. 1 brake tube way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31434C 4.INSTALL CLUTCH RESERVOIR TUBE (for Manual Transaxle)

a.

Connect the clutch reservoir tube to the brake master cylinder sub-assembly with the hose clip.


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 10.BLEED CLUTCH LINE (for Manual Transaxle)