Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for Automatic Transaxle) › 2016.04–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091005 ENGINE ASSEMBLY(for Automatic Transaxle) A

1NZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for Automatic Transaxle)  INSTALLATION  


PROCEDURE

Hide 12372A 1.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A121469E01
0.938,0.844 1.094,1.042 0.156,0.198 10 true 2 2.479,1.188 2.635,1.385 0.156,0.198 10 true 3 1.771,0.063 1.927,0.26 0.156,0.198 10 true 4 1.563,0.292 1.719,0.49 0.156,0.198 10 true 5 1.74,1.906 1.896,2.104 0.156,0.198 10 true 1

Temporarily tighten the engine mounting insulator LH to the vehicle with the 5 bolts.


b.

Fully tighten the 5 bolts, in the sequence shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 12305 2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A121468E01
2.104,0.563 2.26,0.76 0.156,0.198 10 true 1 1.594,0.094 1.75,0.292 0.156,0.198 10 true 2 0.802,1.427 0.938,1.635 0.135,0.208 10 true 3

Temporarily tighten the engine mounting insulator sub-assembly RH to the vehicle with the 3 bolts.


b.

Fully tighten the 3 bolts, in the sequence shown in the illustration.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 3.REMOVE ENGINE STAND

a.

Using a chain block and a sling device, secure the engine assembly.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.

Remove the engine stand from the engine assembly.


Hide 32101 4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using height adjustment attachments or plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments or plate lift attachments, place the engine assembly horizontally.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lifter, secure the engine assembly before servicing.




b.
A166739E01
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A248257C03
1.094,1.719 1.26,1.396 false 2.083,1.854 1.771,1.854 false 2.24,1.083 2.625,1.448 false 0.927,1.667 1.094,1.833 0.167,0.167 10 *1 2.115,1.792 2.281,1.958 0.167,0.167 10 *2 2.646,1.427 2.813,1.594 0.167,0.167 10 *3
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
V100135

Engine Side
V100136

Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly, and rear drive plate spacer to the crankshaft.

NOTICE:

As the drive plate and ring gear sub-assembly and the rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.


HINT:

The front drive plate spacer is reversible.



d.

Clean the 6 bolts and their holes.


e.
A192239C40
1.781,0.552 1.542,1.385 false 1.823,0.458 2,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
A158035E06
1.823,0.542 1.927,0.698 0.104,0.156 10 1 1.833,1.51 1.948,1.677 0.115,0.167 10 2 2.229,0.781 2.385,0.958 0.156,0.177 10 3 1.417,1.271 1.573,1.427 0.156,0.156 10 4 2.24,1.292 2.406,1.458 0.167,0.167 10 5 1.385,0.792 1.552,0.969 0.167,0.177 10 6

Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 30500 5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C248193C01
1.688,1.083 2.75,0.688 true 0.76,0.406 1.115,0.604 false 0.615,0.302 0.927,0.458 0.313,0.156 10 false *1 2.792,0.573 3.104,0.729 0.313,0.156 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)



b.
C283251C01
1.521,0.521 2.781,0.219 2.781,0.219 2.479,1.01 true 2.813,0.115 3.125,0.271 0.313,0.156 10 false *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C283076E01
0.906,0.073 1.052,0.25 0.146,0.177 10 false A 2.365,0.031 2.51,0.208 0.146,0.177 10 false A 2.51,1.885 2.656,2.063 0.146,0.177 10 false B 2.167,2 2.313,2.177 0.146,0.177 10 false B 1.281,2 1.427,2.177 0.146,0.177 10 false B 0.646,0.906 0.792,1.083 0.146,0.177 10 true B 0.906,1.708 1.031,1.885 0.125,0.177 10 true B

Maintain the engine assembly and automatic transaxle assembly in a horizontal position, align the knock pins with each hole in the automatic transaxle assembly and install the automatic transaxle assembly to the engine assembly with the 7 bolts.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the holes.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and automatic transaxle assembly are in close contact with one another.

·

Check that the torque converter assembly rotates.



HINT:
·

Bolt A: Install from automatic transaxle assembly side

·

Bolt B: Install from engine assembly side




Hide 6.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the automatic transaxle assembly with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 28100 7.INSTALL STARTER ASSEMBLY

Hide 11363A 8.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 12321B 9.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 33823 10.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

Hide 25591 13.INSTALL MANIFOLD SUPPORT BRACKET

Hide 17167 14.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17111 15.INSTALL INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

a.

Install a new intake manifold to head gasket to the intake manifold.


b.

Temporarily tighten the intake manifold with throttle body with motor assembly to the cylinder head sub-assembly with the 3 bolts and 2 nuts.


c.
A302829E01
1.594,0.25 1.75,0.448 0.156,0.198 10 true 1 0.917,0.042 1.135,0.219 0.219,0.177 10 true 2 2.25,0.01 2.469,0.188 0.219,0.177 10 true 3 0.135,1.177 0.354,1.354 0.219,0.177 10 true 4 3.115,1.042 3.333,1.219 0.219,0.177 10 true 5

Tighten the 3 bolts and 2 nuts in the sequence shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


d.

Connect the No. 2 water by-pass hose to the No. 1 water by-pass pipe with the hose clip.


e.

Connect the water by-pass hose to the cylinder head sub-assembly with the hose clip.


f.

Connect the union to connector tube hose to the booster vacuum tube with the hose clip.


Hide 15301 16.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 16502 17.INSTALL WATER FILLER SUB-ASSEMBLY

a.
A300597C03
2.542,0.292 2.594,0.458 false 2.094,0.125 2.406,0.281 0.313,0.156 10 false *a 2.667,0.125 2.979,0.281 0.313,0.156 10 false *c 1.74,0.875 1.896,1.073 0.156,0.198 10 true A 2.385,0.146 2.698,0.302 0.313,0.156 10 false *b
*a View A
*b Paint Mark
*c Top of Vehicle


Install the water filler sub-assembly to the throttle body with motor assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Connect the No. 1 radiator hose to the cylinder head sub-assembly with the hose clip as shown in the illustration.


Hide 12261 18.INSTALL VENTILATION HOSE

a.

Install the ventilation hose to the cylinder head cover sub-assembly and intake manifold with the 2 hose clips.


Hide 82121 19.INSTALL ENGINE WIRE

a.

Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


b.

Connect all the engine wire and connectors.


Hide 12281A 20.REMOVE NO. 1 ENGINE HANGER

a.

Remove the 2 bolts and 2 No. 1 engine hangers from the cylinder head sub-assembly.


b.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


c.

Connect the air fuel ratio sensor wire to the wire harness clamp bracket.


Hide 51201 21.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Temporarily tighten the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the through bolt.


Hide 22.INSTALL ENGINE ASSEMBLY WITH AUTOMATIC TRANSAXLE ASSEMBLY

a.

Place height adjustment attachments or plate lift attachments, and then set the engine assembly with automatic transaxle assembly.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with automatic transaxle assembly is level.

·

As the engine assembly with automatic transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the automatic transaxle assembly.




b.

Operate the engine lifter and lift the engine assembly with automatic transaxle assembly and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

CAUTION:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:

Make sure that the engine is clear of all wiring and hoses.



c.

Connect the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)

HINT:

Tighten by holding the nut and turning the through bolt.



d.

Connect the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the bolt and 2 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


e.

By inserting SST into the datum holes in the front suspension crossmember sub-assembly RH and LH alternately, tighten the bolts A, B and C on both sides to the specified torque, in several steps.

SST
09670-00010  

C233133C02
4.458,1.5 4.573,1.302 true 4.094,2.635 4.719,2.635 true 2.781,1.5 2.698,1.292 true 3.135,2.635 2.51,2.635 true 4.313,1.479 4.469,1.625 0.156,0.146 10 false *a 2.802,1.479 2.958,1.625 0.156,0.146 10 false *a 5.563,2.052 5.688,2.198 0.125,0.146 10 false A 5.333,2.458 5.458,2.604 0.125,0.146 10 false B 5.365,2.656 5.49,2.802 0.125,0.146 10 false C 1.51,1.979 1.635,2.125 0.125,0.146 10 false A 1.771,2.427 1.896,2.573 0.125,0.146 10 false B 3.802,2.573 4.104,2.719 0.302,0.146 10 false SST 3.156,2.573 3.458,2.719 0.302,0.146 10 false SST 5.76,3.521 5.99,3.667 0.229,0.146 10 false *c 5.021,3.521 5.25,3.667 0.229,0.146 10 false *b 2.469,3.521 2.698,3.667 0.229,0.146 10 false *c 1.729,3.521 1.958,3.667 0.229,0.146 10 false *b 1.771,2.635 1.896,2.781 0.125,0.146 10 false C
*a Datum Hole *b Correct
*c Incorrect - -
V100135

Front of the Vehicle - -


Torque:
Bolt A : 70 N*m (714 kgf*cm, 52 ft.*lbf)
Bolt B : 165 N*m (1683 kgf*cm, 122 ft.*lbf)
Bolt C : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole vertically.

·

If impossible to insert SST vertically, loosen all bolts and then insert SST again.




f.

Tighten the engine moving control rod bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 45025D 23.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45209 24.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45259A 25.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 32101A 26.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

Hide 43420 28.INSTALL FRONT DRIVE SHAFT ASSEMBLY

Hide 33820B 29.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 17410 31.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 32.INSTALL FRONT FLOOR CENTER BRACE

Hide 58910C 33.INSTALL REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 34.INSTALL REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 82121 35.CONNECT ENGINE WIRE

a.

Connect the engine wire to the automatic transaxle assembly with the bolt.

Torque:
25.5 N*m (260 kgf*cm, 19 ft.*lbf)


b.

Engage the 2 clamps to connect the engine wire to the engine mounting bracket LH.


c.
A304744C01
2.708,0.073 2.896,0.229 0.188,0.156 10 false *a 2.458,0.135 2.729,0.292 0.271,0.156 10 false 45° 1.875,0.677 2.063,0.833 0.188,0.156 10 false *a 3,0.135 3.271,0.292 0.271,0.156 10 false 45°
*a Top of the Vehicle


Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.


d.

Engage the clamp to connect the engine wire to the wire harness clamp bracket.


e.
A304755

Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.


f.

Connect the 3 connectors as shown in the illustration.


g.

Engage the 2 claws to connect the engine wire to the engine room relay block.


h.

Install the nut to the engine room relay block.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


i.

Connect the connector to the engine room relay block.


j.

Engage the clamp to connect the engine wire to the vehicle.


k.

Install the relay block cover to the engine room relay block.


Hide 55550 36.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 88320 37.INSTALL COOLER COMPRESSOR ASSEMBLY (w/o Fan Shroud Ventilation Duct)

a.
A111513E01
1.667,0.896 1.823,1.094 0.156,0.198 10 true 1 1.719,1.781 1.875,1.979 0.156,0.198 10 true 2 2.208,0.917 2.365,1.115 0.156,0.198 10 true 3

Install the cooler compressor assembly to the oil pan sub-assembly with the 3 bolts, in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the cooler compressor assembly connector.


Hide 88320 38.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Fan Shroud Ventilation Duct)

Hide 88712 39.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Fan Shroud Ventilation Duct)

Hide 88711 40.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Fan Shroud Ventilation Duct)

Hide 16361A 41.INSTALL FAN AND GENERATOR V BELT

Hide 16361A 42.ADJUST FAN AND GENERATOR V BELT

Hide 44772 43.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.

Connect the check valve to connector tube hose to the booster vacuum tube with the hose clip.


Hide 23901 46.CONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23842A 47.INSTALL EFI FUEL PIPE CLAMP

Hide 87246 48.CONNECT OUTLET HEATER WATER HOSE

a.
A305931C01
1.74,0.458 2.042,0.313 true 0.979,0.083 1.292,0.281 0.313,0.198 10 false *a 1,0.677 1.313,0.875 0.313,0.198 10 false *d 2.083,0.208 2.396,0.406 0.313,0.198 10 false *b 1.656,0.042 1.969,0.24 0.313,0.198 10 false *c 2.052,2.063 2.292,2.26 0.24,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Front of Vehicle


Connect the outlet heater water hose to the No. 1 water by-pass pipe with the hose clip as shown in the illustration.


Hide 87245 49.CONNECT INLET HEATER WATER HOSE

A305929C01
2.042,0.427 2.281,0.292 false 1.26,0.073 1.573,0.271 0.313,0.198 10 false *a 1.281,0.625 1.594,0.823 0.313,0.198 10 false *d 1.948,0.063 2.26,0.26 0.313,0.198 10 false *c 2.323,0.156 2.635,0.354 0.313,0.198 10 false *b 1.667,2.781 1.979,2.979 0.313,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Front of Vehicle


a.

Connect the inlet heater water hose to the cylinder head sub-assembly with the hose clip as shown in the illustration.


Hide 16572D 50.CONNECT NO. 2 RADIATOR HOSE

a.
A300596C04
2.177,0.438 2.292,0.49 false 1.833,0.135 2.146,0.292 0.313,0.156 10 false *a 2.021,0.302 2.333,0.458 0.313,0.156 10 false *b 2.594,0.135 2.906,0.292 0.313,0.156 10 false *c 1.875,0.771 2.188,0.927 0.313,0.156 10 false *d 2.135,2.083 2.292,2.281 0.156,0.198 10 false A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Right Side of Vehicle


Connect the No. 2 radiator hose to the water inlet with the hose clip as shown in the illustration.


Hide 16573B 51.CONNECT NO. 3 RADIATOR HOSE

A300595C03
0.74,0.302 0.896,0.458 false 0.26,0.198 0.573,0.354 0.313,0.156 10 false *a 0.573,0.198 0.885,0.354 0.313,0.156 10 false *b 0.948,0.167 1.26,0.323 0.313,0.156 10 false *c 1.365,0.563 1.677,0.719 0.313,0.156 10 false *d 2.042,2.135 2.198,2.333 0.156,0.198 10 true A
*a View A
*b Paint Mark
*c Top of Vehicle
*d Right Side of Vehicle


a.

Connect the No. 3 radiator hose to the water filler sub-assembly with the hose clip as shown in the illustration.


Hide 52.CONNECT RADIATOR RESERVOIR TANK HOSE

Hide 17361M 53.INSTALL AIR TUBE

a.

Install the air tube to the cylinder head cover sub-assembly with the bolt.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 74410 54.INSTALL BATTERY CARRIER ASSEMBLY

a.

Install the battery carrier assembly to the engine mounting insulator LH and vehicle with the 5 bolts.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


b.

Engage the 6 clamps to connect the engine wire to the battery carrier assembly.


Hide 74431 55.INSTALL BATTERY TRAY

a.

Install the battery tray to the battery carrier assembly.


Hide 28800 56.INSTALL BATTERY

a.
A300618C01
0.604,1.531 0.75,1.667 true 0.448,1.552 0.365,1.75 true 0.385,0.198 0.531,0.333 true 0.875,0.24 0.75,0.49 true 0.781,1.656 1.094,1.813 0.313,0.156 10 false *1 0.281,1.76 0.448,1.927 0.167,0.167 10 true *2 0.177,0.104 0.417,0.302 0.24,0.198 10 false *3 0.896,0.146 1.073,0.375 0.177,0.229 10 false *4
*1 Battery Clamp Bolt
*2 Battery Carrier
*3 Engine Room Main Wire
*4 Engine Wire


Install the battery to the battery tray.


b.

Install the battery clamp sub-assembly to the battery carrier assembly with the 2 nuts and battery clamp bolt.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)

HINT:

Engage the hook of the battery clamp bolt to the notch of the battery carrier assembly.



c.

Engage the 2 claws to connect the engine room main wire to the engine wire.


d.

Connect the engine room main wire with engine wire to the positive (+) battery terminal with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


e.

Install the terminal cover to the positive (+) battery terminal.


Hide 23820 57.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY

a.

Install the fuel vapor feed hose assembly to the cylinder head cover sub-assembly and fuel tube with the 2 hose clips.


Hide 58.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the air cleaner bracket with the 3 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Engage the clamp to connect the engine wire to the air cleaner case sub-assembly.


Hide 17801 59.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17735 60.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 23827A 62.CONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 23820 63.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 64.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 16361A 65.INSPECT FAN AND GENERATOR V BELT

Hide 66.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 70.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (w/ Fan Shroud Ventilation Duct)

Hide 71.WARM UP ENGINE (w/ Fan Shroud Ventilation Duct)

Hide 72.INSPECT FOR REFRIGERANT LEAK (w/ Fan Shroud Ventilation Duct)

Hide 75.INSPECT FOR ENGINE OIL LEAK

Hide 76.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK

Hide 78.INSPECT FOR EXHAUST GAS LEAK

Hide 83.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 51441C 84.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

Install the engine under cover RH to the vehicle with the 2 bolts and 2 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51442C 85.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

a.

Install the engine under cover LH to the vehicle with the 3 bolts and 5 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51405A 86.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

a.

Install the No. 1 engine under cover sub-assembly to the vehicle with the 11 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 51451A 87.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

a.

Install the center engine under cover to the vehicle with the 4 screws and 5 clips.