While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0617 | Starter Relay Circuit High | Following conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):
(a) Vehicle speed 20 km/h (12.4 mph) or more (b) Engine speed more than 1000 rpm (c) STA signal ON |
·
Clutch start switch assembly ·
Starter relay circuit ·
Ignition or start switch assembly ·
ECM |
Comes on | DTC stored |
| Required Sensors/Components (Main) | Starter relay
Clutch start switch assembly Ignition or starter switch assembly |
| Required Sensors/Components (Related) | Vehicle speed sensor
Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Vehicle speed | 20 km/h (12.4 mph) or more |
| Engine speed | 1000 rpm or more |
| Starter signal | ON |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Idle the engine for 5 seconds or more [B].
Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0617.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.
Inspect the fuses for circuits related to this system before performing the following procedure.
The following troubleshooting flowchart is based on the premise that the engine is cranked normally.
If the engine will not crank, proceed to the Problem Symptoms Table.
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>PROBLEM SYMPTOMS TABLE
Read freeze frame data using the GTS. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
| Condition | GTS Display | Proceed to |
|---|---|---|
| Driving at 20 km/h (12.4 mph) or more | OFF | A |
| ON | B |
A
B
Disconnect the A28 clutch start switch assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Read the value displayed on the GTS when the ignition switch is ON.
| Result | Proceed to |
|---|---|
| ON | A |
| OFF | B |
A
B
| *a | Rear view of wire harness connector
(to ECM) |
Disconnect the A28 clutch start switch assembly connector.
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
|---|---|---|---|
| F81-3 (STA) - Body ground | Ignition switch ON | 11 to 14 V | A |
| Below 1.5 V | B |
A
B
Inspect the clutch start switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the clutch start switch assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>1NZ-FE STARTING>IGNITION SWITCH>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the A28 clutch start switch assembly connector.
Disconnect the F81 ECM connector.
Disconnect the F7 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-2, F81-16 (NSW) or F7-7 (ST2) - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG