Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2016.04–2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0092015 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

If the spiral cable sub-assembly is installed with the center position misaligned, steering angle sensor value abnormal DTCs will be stored, and recovery will be impossible. In this case, replace the spiral cable sub-assembly with a new one.


a.

Check the spiral cable sub-assembly center position.

Standard:

Connector is at the highest point.

Alignment marks are aligned.

Colored roller or top of flat cable U-turn portion can be seen through the check window.


B475929C01
1.469,1.302 1.052,0.885 true 1.5,1.458 0.917,2.333 true 2.031,2.167 2.417,2.333 2.417,2.333 2.031,2.042 true 5.438,2.167 5.823,2.333 5.823,2.333 5.438,2.042 true 4.948,1.667 4.583,2.5 true 4.865,1.604 4.448,1.188 true 0.417,0.167 0.667,0.417 0.25,0.25 12 false *A 4.167,0.167 4.417,0.417 0.25,0.25 12 false *B 0.875,0.813 1.188,0.969 0.313,0.156 10 false *a 2.479,2.25 2.792,2.406 0.313,0.156 10 false *b 0.708,2.25 1.021,2.406 0.313,0.156 10 false *c 4.24,1.094 4.552,1.25 0.313,0.156 10 false *a 4.385,2.417 4.698,2.573 0.313,0.156 10 false *d 5.896,2.25 6.208,2.406 0.313,0.156 10 false *b
*A Colored Roller Visible Type *B Flat Cable Visible Type
*a Check Window *b Alignment Marks
*c Colored Roller *d Top of U-turn Portion of Flat Cable



b.

If the spiral cable sub-assembly is not at the center position, perform centering of the spiral cable sub-assembly.

NOTICE:

Failure to observe the following precautions could result in breakage of the spiral cable sub-assembly.

·

Do not hold the airbag connector or wiring when rotating the spiral cable sub-assembly.

·

Do not rotate with excessive force.



i.
B475931C01
0,0 0,0 false
V100135

Rotation Direction


Making sure to rotate in the counterclockwise direction only, slowly rotate the spiral cable sub-assembly in the counterclockwise direction until it stops.

NOTICE:

Make sure to rotate in the counterclockwise direction only. Rotating in the clockwise direction can break the spiral cable sub-assembly or make centering impossible.



ii.
B475933

When the rotation stops, if the connector has passed the lowermost position, return the connector to the lowermost position as shown in the illustration.


iii.
B475935C01
0,0 0,0 false
V100135

Rotation Direction


Rotate the spiral cable sub-assembly back in the clockwise direction for approximately 2.5 turns so that the connector moves from the lowermost position to the topmost position.

NOTICE:

With the connector in the lowermost position, rotating clockwise 5 turns or more could break the spiral cable sub-assembly.



iv.

Check that the spiral cable sub-assembly is centered.

Standard:

Connector is at the highest point.

Alignment marks are aligned.

Colored roller or top of flat cable U-turn portion can be seen through the check window.


B475929C01
1.469,1.302 1.052,0.885 true 1.5,1.458 0.917,2.333 true 2.031,2.167 2.417,2.333 2.417,2.333 2.031,2.042 true 5.438,2.167 5.823,2.333 5.823,2.333 5.438,2.042 true 4.948,1.667 4.583,2.5 true 4.865,1.604 4.448,1.188 true 0.417,0.167 0.667,0.417 0.25,0.25 12 false *A 4.167,0.167 4.417,0.417 0.25,0.25 12 false *B 0.875,0.813 1.188,0.969 0.313,0.156 10 false *a 2.479,2.25 2.792,2.406 0.313,0.156 10 false *b 0.708,2.25 1.021,2.406 0.313,0.156 10 false *c 4.24,1.094 4.552,1.25 0.313,0.156 10 false *a 4.385,2.417 4.698,2.573 0.313,0.156 10 false *d 5.896,2.25 6.208,2.406 0.313,0.156 10 false *b
*A Colored Roller Visible Type *B Flat Cable Visible Type
*a Check Window *b Alignment Marks
*c Colored Roller *d Top of U-turn Portion of Flat Cable


NOTICE:

If centering cannot be achieved, the spiral cable sub-assembly may be broken, so replace it with a new one.




Hide 84306 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the front wheels are facing straight ahead.


d.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch pin may snap.



e.

Engage the 3 claws to install the spiral cable sub-assembly.

NOTICE:

Pull the lock pin out before installing the steering wheel assembly when replacing the spiral cable sub-assembly with a new one.



f.

Connect the connectors to the spiral cable sub-assembly.


Hide 45286B 3.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 4.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

Do not adjust the spiral cable sub-assembly with the battery connected and the ignition switch to ON.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check the spiral cable sub-assembly center position.

Standard:

Connector is at the highest point.

Colored roller or top of flat cable U-turn portion can be seen through the check window.


B475913C01
0.552,1.906 0.219,1.406 true 4.042,1.979 3.708,1.479 true 1.125,2.615 0.625,2.115 true 4.656,2.563 4.156,2.063 true 0.24,0.083 0.49,0.333 0.25,0.25 12 false *A 3.823,0.083 4.073,0.333 0.25,0.25 12 false *B 0.021,1.313 0.333,1.469 0.313,0.156 10 false *a 1.198,2.51 1.51,2.667 0.313,0.156 10 false *b 4.74,2.458 5.052,2.615 0.313,0.156 10 false *c 3.51,1.365 3.823,1.521 0.313,0.156 10 false *a
*A Colored Roller Visible Type *B Flat Cable Visible Type
*a Check Window *b Colored Roller
*c Top of U-turn Portion of Flat Cable - -



d.

If the spiral cable sub-assembly is not at the center position, perform centering of the spiral cable sub-assembly.

NOTICE:

Failure to observe the following precautions could result in breakage of the spiral cable sub-assembly.

·

Do not rotate the spiral cable sub-assembly while the negative (-) battery cable is connected and the ignition switch is turned to ON.

·

Do not hold the airbag connector or wiring when rotating the spiral cable sub-assembly.

·

Do not rotate with excessive force.



i.
B346979C01
0,0 0,0 false
V100135

Rotation Direction


Making sure to rotate in the counterclockwise direction only, slowly rotate the spiral cable sub-assembly in the counterclockwise direction until it stops.

NOTICE:

Make sure to rotate in the counterclockwise direction only. Rotating in the clockwise direction can break the spiral cable sub-assembly or make centering impossible.



ii.
B475911

When the rotation stops, if the connector has passed the lowermost position, return the connector to the lowermost position as shown in the illustration.


iii.
B475912C01
0,0 0,0 false
V100135

Rotation Direction


Rotate the spiral cable sub-assembly back in the clockwise direction for approximately 2.5 turns so that the connector moves from the lowermost position to the topmost position.

NOTICE:

With the connector in the lowermost position, rotating clockwise 5 turns or more could break the spiral cable sub-assembly.



iv.

Check that the spiral cable sub-assembly is centered.

Standard:

Connector is at the highest point.

Colored roller or top of flat cable U-turn portion can be seen through the check window.


B475913C01
0.552,1.906 0.219,1.406 true 4.042,1.979 3.708,1.479 true 1.125,2.615 0.625,2.115 true 4.656,2.563 4.156,2.063 true 0.24,0.083 0.49,0.333 0.25,0.25 12 false *A 3.823,0.083 4.073,0.333 0.25,0.25 12 false *B 0.021,1.313 0.333,1.469 0.313,0.156 10 false *a 1.198,2.51 1.51,2.667 0.313,0.156 10 false *b 4.74,2.458 5.052,2.615 0.313,0.156 10 false *c 3.51,1.365 3.823,1.521 0.313,0.156 10 false *a
*A Colored Roller Visible Type *B Flat Cable Visible Type
*a Check Window *b Colored Roller
*c Top of U-turn Portion of Flat Cable - -


NOTICE:

If centering cannot be achieved, the spiral cable sub-assembly may be broken, so replace it with a new one.




Hide 45100 6.INSTALL STEERING WHEEL ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)