Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.07–2016.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line (LHD Models)  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

No. 1 CAN junction connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected to a CAN main bus branch.

WIRING DIAGRAM

E340830E02
0.104,0.073 1.021,0.271 0.917,0.198 10 false V Bus: 3.229,0.156 4,0.354 0.771,0.198 10 false 120 Ω 3.229,4.583 4,4.781 0.771,0.198 10 false 120 Ω 2.49,0.75 3.104,0.948 0.615,0.198 10 false CANL 3.99,0.75 4.604,0.948 0.615,0.198 10 false CANH 4.5,0.49 6.521,0.823 2.021,0.333 10 false Combination Meter Assembly 4.5,0.323 4.958,0.521 0.458,0.198 10 false F38 4.26,1.802 4.573,2 0.313,0.198 10 false 1 2.719,0.969 3.031,1.167 0.313,0.198 10 false 31 3.969,0.99 4.281,1.188 0.313,0.198 10 false 32 4,1.24 4.313,1.438 0.313,0.198 10 false G 2.688,1.24 3,1.438 0.313,0.198 10 false W 2.74,1.5 3.052,1.698 0.313,0.198 10 false 17 3.969,1.5 4.281,1.698 0.313,0.198 10 false 6 5.531,1.802 5.844,2 0.313,0.198 10 false 6 4.26,2.167 4.573,2.365 0.313,0.198 10 false 12 5.531,2.167 5.844,2.365 0.313,0.198 10 false 14 4.896,2.104 5.208,2.302 0.313,0.198 10 false W 4.854,1.74 5.198,1.938 0.344,0.198 10 false GR 5.76,1.906 6.375,2.104 0.615,0.198 10 false CANH 5.906,2.271 6.521,2.469 0.615,0.198 10 false CANL 6.063,2.521 6.427,2.719 0.365,0.198 10 false F16 6.063,2.688 6.677,2.885 0.615,0.198 10 false DLC3 0.656,2.156 4.938,2.354 4.281,0.198 10 false No. 1 CAN Junction Connector 0.656,1.99 1.115,2.188 0.458,0.198 10 false F62 2.719,2.677 3.031,2.875 0.313,0.198 10 false 14 3.969,2.677 4.281,2.875 0.313,0.198 10 false 3 2.688,2.948 3,3.146 0.313,0.198 10 false W 4,2.938 4.313,3.135 0.313,0.198 10 false BE 2.802,3.406 3.417,3.604 0.615,0.198 10 false F130 3.729,3.406 4.344,3.604 0.615,0.198 10 false F130 3.771,3.573 4.385,3.771 0.615,0.198 10 false F82 3.771,3.75 4.385,3.948 0.615,0.198 10 false F81 2.833,3.75 3.448,3.948 0.615,0.198 10 false F81 2.833,3.573 3.448,3.771 0.615,0.198 10 false F82 2.531,3.406 2.844,3.604 0.313,0.198 10 false 14 2.531,3.573 2.844,3.771 0.313,0.198 10 false 34 2.604,3.75 2.917,3.948 0.313,0.198 10 false 7 3.188,3.406 3.5,3.604 0.313,0.198 10 false *3 3.188,3.573 3.5,3.771 0.313,0.198 10 false *2 3.188,3.75 3.5,3.948 0.313,0.198 10 false *1 4.115,3.385 4.427,3.583 0.313,0.198 10 false 13 4.125,3.563 4.438,3.76 0.313,0.198 10 false 33 4.156,3.75 4.469,3.948 0.313,0.198 10 false 8 3.479,3.396 3.76,3.594 0.281,0.198 10 false *3 3.479,3.583 3.76,3.771 0.281,0.188 10 false *2 3.479,3.76 3.76,3.948 0.281,0.188 10 false *1 2.49,3.969 3.104,4.167 0.615,0.198 10 false CANL 3.99,3.969 4.604,4.167 0.615,0.198 10 false CANH 0.25,5.25 6.615,5.563 6.365,0.313 10 false *1: for 2NZ-FE with Manual Transaxle 0.25,5.583 6.615,5.896 6.365,0.313 10 false *2: for Automatic Transaxle 0.25,5.917 6.615,6.229 6.365,0.313 10 false *3: for 1NR-FE or 2NR-FE 0.302,6.25 6.667,6.563 6.365,0.313 10 false x: Suspected Area 3.865,6.865 7.156,7.208 3.292,0.344 10 false : CAN Branch Line (CANH) 3.865,7.26 7.156,7.604 3.292,0.344 10 false : CAN Branch Line (CANL) 0.719,6.865 4.01,7.208 3.292,0.344 10 false : CAN Main Bus Line (CANH) 0.74,7.271 4.031,7.615 3.292,0.344 10 false : CAN Main Bus Line (CANL) 4.5,4.177 5.115,4.375 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C152423C10
1.427,0.167 1.854,0.427 0.427,0.26 1.938,0.927 2.354,0.417 true 1.938,1.438 1.49,1.844 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *1 1.51,0.198 1.969,0.396 0.458,0.198 10 false F16 2.417,0.292 3.031,0.49 0.615,0.198 10 false CANH 1.094,1.792 1.708,1.99 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Proceed to
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.
E221291C36
1.5,0.25 1.917,0.5 0.417,0.25 1.781,1.385 1.552,1.771 true 1.906,1.396 2.104,1.75 true 1.604,0.292 2.083,0.51 0.479,0.219 10 false F38 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 1.365,1.802 1.792,2.042 0.427,0.24 10 false CANL 1.938,1.792 2.375,2.031 0.438,0.24 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (for 2NZ-FE with Manual Transaxle) B
NG (for Automatic Transaxle) C
NG (for 1NR-FE or 2NR-FE) D



A

REPLACE COMBINATION METER ASSEMBLY

B

3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)

D

5.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
3.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271714C03
1.542,0.417 1.969,0.667 0.427,0.25 1.677,2.781 2.021,1.688 true 2.188,1.698 2.469,2.76 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.635,0.458 2.094,0.656 0.458,0.198 10 false F81 2.302,2.823 2.917,3.021 0.615,0.198 10 false CANH 1.5,2.833 2.115,3.031 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-8 (CANH) - F81-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271715C17
1.49,0.5 1.896,0.75 0.406,0.25 2.271,2.26 2,2.896 true 2.458,2.271 2.75,2.896 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.542 2.031,0.74 0.458,0.198 10 false F82 1.781,2.917 2.396,3.115 0.615,0.198 10 false CANH 2.604,2.917 3.219,3.115 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F82-33 (CANH) - F82-34 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1NZ-FE) A
OK (for 2NZ-FE) B
NG C



A

B

C

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
C343963C17
1.406,0.083 1.906,0.333 0.5,0.25 2.5,1.833 2.083,1.146 true 1.583,1.833 1.948,1.167 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.5,0.125 1.948,0.333 0.448,0.208 10 false F130 1.365,1.875 1.813,2.083 0.448,0.208 10 false CANH 2.344,1.875 2.792,2.083 0.448,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-13 (CANH) - F130-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F81*1, F82*2 or F130*3 ECM connector.

*1: for 2NZ-FE with Manual Transaxle

*2: for Automatic Transaxle

*3: for 1NR-FE or 2NR-FE



b.
C290986C01
1.427,0.667 1.906,0.927 0.479,0.26 1.698,1.729 0.667,1.156 true 1.271,1.729 0.667,1.458 true 1.26,2.031 0.698,2.354 true 1.688,2.042 0.688,2.667 true 0.208,0.219 0.521,0.375 0.313,0.156 10 false *a 0.135,1.063 0.781,1.25 0.646,0.188 10 false CANH*c 1.552,0.708 1.875,0.896 0.323,0.188 10 false F62 0.135,1.365 0.781,1.552 0.646,0.188 10 false CANH*b 0.167,2.271 0.813,2.458 0.646,0.188 10 false CANL*b 0.177,2.594 0.823,2.781 0.646,0.188 10 false CANL*c
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to ECM
*c to Combination Meter Assembly


Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-3 (CANH) - F62-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F62-6 (CANH) - F62-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (Combination meter assembly main line) B
NG (ECM main line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)