When there is a communication malfunction between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2799 | Engine Immobiliser System Malfunction | Either condition is met (1 trip detection logic*1):
·
A malfunction in the communication or communication lines between the ECM and certification ECU (smart key ECU assembly). ·
A matching communication code cannot be verified during communication between the ECM and certification ECU (smart key ECU assembly). |
·
Certification ECU (smart key ECU assembly) ·
ECM ·
Wire harness or connector |
DTC output confirmation operation (Either condition is met):
·
Within 10 seconds of an engine start operation being performed (with the shift lever in P*2 and the brake pedal*2 or clutch pedal*3 depressed, the engine switch is pressed while the key is being carried). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds). ·
10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds). |
*1: Only output while a malfunction is present.
*2: for Automatic Transaxle and CVT
*3: for Manual Transaxle
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2799 | - |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."
When DTC B2799 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
Reregister the ECU communication ID.
Refer to Service Bulletin
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
B2799 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2799 is output) | B |
| NG (Other DTCs are output) | C |
A
B
C
for 1NZ-FE, 2NZ-FE
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F82-15 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
for 1NR-FE, 2NR-FE
Using an oscilloscope, check the waveform.
| *A | for CVT | *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F130-9 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
The waveform is similar to that shown in the illustration.
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Terminal IMO stuck low (2.4 V or less) | B |
| Terminal IMO stuck high (12 V) or Abnormal waveform | C |
A
B
C
for 1NZ-FE, 2NZ-FE
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F82-16 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
for 1NR-FE, 2NR-FE
Using an oscilloscope, check the waveform.
| *A | for CVT | *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F130-10 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected |
The waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered vehicle key, turn the engine switch on (IG).
Check that the engine starts 5 seconds after the engine switch turned on (IG).
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the ECM with a new one.
for 1NZ-FE: Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>ECM>REMOVAL
for 2NZ-FE: Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>ECM>REMOVAL
for 1NR-FE: Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>ECM>REMOVAL
for 2NR-FE: Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered vehicle key, turn the engine switch on (IG).
Check that the engine starts 5 seconds after the engine switch turned on (IG).
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1NZ-FE, 2NZ-FE
Disconnect the ECM connector.
Turn the engine switch on (IG).
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Result |
|---|---|---|
| F82-15 (IMO) - Body ground | Engine switch on (IG) using registered key | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or Abnormal waveform |
for 1NR-FE, 2NR-FE
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Result |
|---|---|---|
| F130-9 (IMO) - Body ground | Engine switch on (IG) using registered key | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or Abnormal waveform |
| Result | Proceed to |
|---|---|
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) or Abnormal waveform | B |
A
B
for 1NZ-FE, 2NZ-FE
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F82 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-3 (EFII) - F82-15 (IMO) | Always | Below 1 Ω |
| F44-35 (EFIO) - F82-16 (IMI) | Always | Below 1 Ω |
| F82-15 (IMO) - Body ground | Always | 10 kΩ or higher |
| F43-3 (EFII) - Body ground | Always | 10 kΩ or higher |
| F82-16 (IMI) - Body ground | Always | 10 kΩ or higher |
| F44-35 (EFIO) - Body ground | Always | 10 kΩ or higher |
for 1NR-FE, 2NR-FE
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
Disconnect the F130 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-3 (EFII) - F130-9 (IMO) | Always | Below 1 Ω |
| F44-35 (EFIO) - F130-10 (IMI) | Always | Below 1 Ω |
| F130-9 (IMO) - Body ground | Always | 10 kΩ or higher |
| F43-3 (EFII) - Body ground | Always | 10 kΩ or higher |
| F130-10 (IMI) - Body ground | Always | 10 kΩ or higher |
| F44-35 (EFIO) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
Recognition code registration is necessary when replacing the certification ECU (smart key ECU assembly).
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered vehicle key, turn the engine switch on (IG).
Check that the engine starts 5 seconds after the engine switch was turn on (IG).
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
| NG (for 1NR-FE) | D |
| NG (for 2NR-FE) | E |
A
B
C
D
E