Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Hatchback) › from 2017.10
RM30M0E _58 Vehicle Interior _017120 INTERIOR PANELS / TRIM _0116072 ROOF HEADLINING(for Hatchback) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Hatchback)  REMOVAL  


PROCEDURE

Hide 64330 1.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

a.
B484763

Separate the 2 suspenders from the package tray trim hanger.


b.

Disengage the 2 guides to remove the package tray trim panel assembly.


Hide 64711E 2.REMOVE LUGGAGE COMPARTMENT FLOOR MAT

a.
B484764

Remove the luggage compartment floor mat.


Hide 58410B 3.REMOVE DECK BOARD ASSEMBLY

a.
B484765

Remove the deck board assembly.


Hide 64772 4.REMOVE SPARE WHEEL COVER PAD

a.
B484766

Remove the spare wheel cover pad.


Hide 64773B 5.REMOVE NO. 2 SPARE WHEEL COVER PAD

a.
B484767

Remove the No. 2 spare wheel cover pad.


Hide 6.REMOVE REAR SEAT ASSEMBLY (for Separate Seat Type)

Hide 7.REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 67914 8.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B487704C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the 8 claws to remove the front door scuff plate LH as shown in the illustration.


Hide 67913 9.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 10.REMOVE COWL SIDE TRIM BOARD LH

a.
B487705C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


b.

Disengage the 2 clips to remove the cowl side trim board LH as shown in the illustration.


Hide 62111C 11.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 12.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B487706

Remove the front door opening trim weatherstrip LH.


Hide 62311B 13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62212 14.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.
B487707C01
2.26,0.75 2.417,0.573 false 2.083,0.75 2.396,0.948 0.313,0.198 10 false *1
*1 Front Pillar Garnish Clip
V113147

Remove in this Direction


Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip as shown in the illustration.

HINT:

Let the front pillar garnish LH hang from the front pillar garnish clip.



b.
B484555C01
2.396,1.156 2.604,0.906 false 2.208,1.146 2.521,1.344 0.313,0.198 10 false *1
*1 Front Pillar Garnish Clip
V100135

Push
V113147

Remove in this Direction


While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

HINT:

When the front pillar garnish clip cannot be disengaged easily.


1.
B487738C01
0,0 0,0 false
V100135

Push
V113147

Move in this Direction


While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

2.
B487739C01
0,0 0,0 false
V113147

Pull in this Direction


While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.



c.
B484556C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.


d.

Remove the front pillar garnish clip.


e.
B484777

for LH side:

i.

Disengage the 4 clamps.


ii.

Disconnect the connector to disconnect the No. 1 roof wire.



f.
B484775C02
1.646,2.292 2.385,3.063 true 2.01,1.802 2.708,1.656 2.708,1.656 2.542,1.073 true 1.417,2.625 1.542,3.073 true 2.771,1.625 3.083,1.781 0.313,0.156 10 false *a 2.448,3.104 2.76,3.26 0.313,0.156 10 false *b 1.49,3.104 1.802,3.26 0.313,0.156 10 false *a
*a Clamp
*b Hook


for RH side:

i.

Disengage the 3 clamps.


ii.

Disconnect the connector.


iii.

Remove the bolt.


iv.

Disengage the hook to disconnect the No. 2 antenna cord sub-assembly.



g.
B487740C01
0.469,1.583 0.833,1.344 true 1.635,1.344 2,1.104 true 2.042,2 2.406,1.76 true 0.271,1.531 0.583,1.729 0.313,0.198 10 false *1 2.073,1.021 2.385,1.219 0.313,0.198 10 false *a 2.5,1.708 2.813,1.906 0.313,0.198 10 false *b
*1 Curtain Shield Airbag Assembly LH
*a Protective Cover
*b Adhesive Tape


Protect the curtain shield airbag assembly.

i.

Cover the curtain shield airbag assembly with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish is removed.




Hide 62211 15.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 62212 16.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.
B489624C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the 2 clips and 2 guides to remove the front pillar garnish LH as shown in the illustration.


b.
B484777

for LH side:

i.

Disengage the 4 clamps.


ii.

Disconnect the connector to disconnect the No. 1 roof wire.



c.
B484775C02
1.646,2.292 2.385,3.063 true 2.01,1.802 2.708,1.656 2.708,1.656 2.542,1.073 true 1.417,2.625 1.542,3.073 true 2.771,1.625 3.083,1.781 0.313,0.156 10 false *a 2.448,3.104 2.76,3.26 0.313,0.156 10 false *b 1.49,3.104 1.802,3.26 0.313,0.156 10 false *a
*a Clamp
*b Hook


for RH side:

i.

Disengage the 4 clamps.


ii.

Disconnect the connector.


iii.

Remove the bolt.


iv.

Disengage the hook to disconnect the No. 2 antenna cord sub-assembly.



Hide 62211 17.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 67918A 18.REMOVE REAR DOOR SCUFF PLATE LH

a.
B487741C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws as shown in the illustration.


b.
B484557C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the 3 claws and guide to remove the rear door scuff plate LH as shown in the illustration.


Hide 67917A 19.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 20.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B487742

Remove the rear door opening trim weatherstrip LH.


Hide 62331A 21.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73220 22.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B487743

Remove the bolt to disconnect the front seat outer belt assembly LH.


Hide 73210 23.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 24.REMOVE CENTER PILLAR LOWER GARNISH LH

a.
B487744C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Disengage the 2 claws, 2 clips and 2 guides to remove the center pillar lower garnish LH as shown in the illustration.


Hide 62413A 25.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62412B 26.REMOVE CENTER PILLAR UPPER GARNISH LH

a.
B487745C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 screws.


b.

Disengage the clip and guide to disconnect the center pillar garnish LH as shown in the illustration.


c.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH to remove the center pillar upper garnish LH.


Hide 62411B 27.REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 28.REMOVE REAR DECK TRIM COVER

a.
B484785C01
0,0 0,0 false
V113147

Remove in this Direction


Using a clip remover, remove the 2 clips.


b.

Disengage the 4 claws and 2 guides to remove the rear deck trim cover as shown in the illustration.


Hide 64740C 29.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.
B487746

Using a clip remover, remove the 7 clips and deck trim side panel assembly LH.


Hide 64730B 30.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73370 31.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

a.
B487747

Remove the bolt.


b.

Disengage the clamp to disconnect the rear seat 3 point type outer belt assembly LH.


Hide 73360 32.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62552F 33.REMOVE REAR SEAT SIDE GARNISH LH

a.
B487748C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws, clip and guide to remove the rear seat side garnish LH as shown in the illustration.


Hide 62551F 34.REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 81330 35.REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 62572A 36.REMOVE ROOF SIDE INNER LOWER GARNISH LH

a.
B487749C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the screw.


b.

Disengage the 5 claws and 2 clips to remove the roof side inner lower garnish LH as shown in the illustration.


Hide 62571A 37.REMOVE ROOF SIDE INNER LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73310D 38.DISCONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY

a.
B484792C02
1.521,1.51 1.854,1.802 true 1.958,1.76 2.271,1.958 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws to open the guide cover of the rear center seat 3 point type belt assembly.


b.
B484793

Remove the bolt to disconnect the slip anchor of the rear center seat 3 point type belt assembly.


c.
B484794C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws and 2 guides to disconnect the belt guide of the rear center seat 3 point type belt assembly as shown in the illustration.


Hide 62472A 39.REMOVE ROOF SIDE INNER GARNISH LH

a.
B484795C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 clips.


b.

Disengage the guide (rear seatback rod knob LH) as shown in the illustration.


c.

Pass the slip anchor of the rear center seat 3 point type belt assembly through the roof side inner garnish LH and remove the roof side inner garnish LH.


Hide 62471A 40.REMOVE ROOF SIDE INNER GARNISH RH

a.
B484790C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 clips.


b.

Disengage the guide (rear seatback rod knob RH) to remove the roof side inner garnish RH as shown in the illustration.


Hide 81260A 41.REMOVE MAP LIGHT ASSEMBLY

Hide 81240J 42.REMOVE ROOM LIGHT ASSEMBLY

Hide 74610A 43.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure to remove all assist grip sub-assemblies.


a.
B487522C01
3.01,0.854 2.615,0.573 true 2.542,1.938 2.01,2.281 true 3.063,0.844 3.375,1 0.313,0.156 10 false *a 2.604,1.833 3.063,2.031 0.458,0.198 10 false SST
*a Cutout


Insert SST straight into the cutout of the assist grip cover.

SST
09813-00010  

NOTICE:

To prevent scratches or damage, make sure to insert SST straight relative to the cutout.



b.
B487523C01
2.604,1.5 2.813,1.813 true 2.083,1.979 2.396,2.135 0.313,0.156 10 false *a 2.719,1.875 3.177,2.073 0.458,0.198 10 false SST
*a 30 to 45°
V113147

Remove in this Direction


Pull SST in the direction indicated by the arrows in the illustration to disengage the claw of the assist grip cover.

HINT:

Use the same procedure to disengage the opposite side.



c.

Remove the assist grip cover.

HINT:

Use the same procedure to disengage the opposite side.



d.
B484797

Disengage the 2 clips to remove the assist grip.


e.

Remove the 2 clips from the vehicle body.


Hide 74320 44.REMOVE VISOR ASSEMBLY LH

a.
B487750

Disengage the guide.


b.

Remove the 2 screws and visor assembly LH.


Hide 74310 45.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 46.REMOVE VISOR HOLDER LH

a.
B487751C01
1.115,0.448 1.427,0.646 0.313,0.198 10 false *a
*a 45°
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder LH approximately 45° and pull it out as shown in the illustration.


b.
B487752

Disengage the 2 claws to remove the visor holder LH.


Hide 47.REMOVE VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 63310 48.REMOVE ROOF HEADLINING ASSEMBLY

a.

for Rear Pillar RH Side:

i.
B484791

Disengage the clamp.


ii.

Disconnect the connector.


iii.

Remove the bolt.


iv.

Disengage the hook to disconnect the No. 2 antenna cord sub-assembly.



b.
B484802

Using a clip remover, remove the 2 clips.


c.
B484803C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the roof headlining assembly from the vehicle through the back door as shown in the illustration.

NOTICE:

Do not damage the roof headlining assembly or body interior.