The combination meter assembly receives the headlight dimmer switch assembly (turn signal switch) information and controls the turn signal lights.
for TMMIN Made
for TMT Made
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Turn Signal Switch (Right) | Turn signal switch (Right) signal | ON or OFF | ON: Turn signal switch (Right) on
OFF: Turn signal switch (Right) off |
- |
| Turn Signal Switch (Left) | Turn signal switch (Left) signal | ON or OFF | ON: Turn signal switch (Left) on
OFF: Turn signal switch (Left) off |
- |
| Tester Display |
|---|
| Turn Signal Switch (Right) |
| Turn Signal Switch (Left) |
Normal conditions listed above are displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMMIN Made | A |
| for TMT Made | B |
A
B
Inspect the headlight dimmer switch assembly (turn signal switch).
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Projector Headlight) | A |
| OK (w/o Projector Headlight) | B |
| NG | C |
A
B
C
Disconnect the F17 headlight dimmer switch assembly connector.
Disconnect the F39 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F17-13 (TR) - F39-9 (ER) | Always | Below 1 Ω |
| F17-15 (TL) - F39-10 (EL) | Always | Below 1 Ω |
| F17-12 (EL) - Body ground | Always | Below 1 Ω |
| F17-13 (TR) or F39-9 (ER) - Body ground | Always | 10 kΩ or higher |
| F17-15 (TL) or F39-10 (EL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F86 headlight dimmer switch assembly connector.
Disconnect the F39 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F86-6 (TR) - F39-9 (ER) | Always | Below 1 Ω |
| F86-5 (TL) - F39-10 (EL) | Always | Below 1 Ω |
| F86-7 (E) - Body ground | Always | Below 1 Ω |
| F86-6 (TR) or F39-9 (ER) - Body ground | Always | 10 kΩ or higher |
| F86-5 (TL) or F39-10 (EL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the headlight dimmer switch assembly (turn signal switch).
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT DIMMER SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F17 headlight dimmer switch assembly connector.
Disconnect the F39 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
for LHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F17-12 (TR) - F39-9 (ER) | Always | Below 1 Ω |
| F17-11 (TL) - F39-10 (EL) | Always | Below 1 Ω |
| F17-15 (EL) - Body ground | Always | Below 1 Ω |
| F17-12 (TR) or F39-9 (ER) - Body ground | Always | 10 kΩ or higher |
| F17-11 (TL) or F39-10 (EL) - Body ground | Always | 10 kΩ or higher |
for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F17-20 (TR) - F39-9 (ER) | Always | Below 1 Ω |
| F17-19 (TL) - F39-10 (EL) | Always | Below 1 Ω |
| F17-16 (EL) - Body ground | Always | Below 1 Ω |
| F17-20 (TR) or F39-9 (ER) - Body ground | Always | 10 kΩ or higher |
| F17-19 (TL) or F39-10 (EL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG