Home › Vehicle Interior › SEAT BELT › REAR SEAT INNER BELT ASSEMBLY(for 3 Point Type Rear Center Seat Belt LH Side) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0092629 REAR SEAT INNER BELT ASSEMBLY(for 3 Point Type Rear Center Seat Belt LH Side) A

SEAT BELT  REAR SEAT INNER BELT ASSEMBLY(for 3 Point Type Rear Center Seat Belt LH Side)  INSTALLATION  


PROCEDURE

Hide 73480 1.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Sedan)

a.
B370037C01
2.813,0.74 3.125,0.938 0.313,0.198 10 false *a 2.042,2.01 2.354,2.156 0.313,0.146 10 false *b 2.49,1.427 2.76,1.615 0.271,0.188 10 false 45°
*a Unlock
*b Lock


Check the angle of inclination required to lock the retractor.

i.

Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

NOTICE:

Do not disassemble the retractor.


If the operation is not as specified, replace the rear seat inner with center belt assembly LH.



Hide 73480 2.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Sedan)

a.

Engage the guide to install the rear seat inner with center belt assembly LH.


b.

Install the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Connect the floor anchor part of the rear seat inner with center belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


d.

Check that the ELR locks.

NOTICE:

Perform the check with the rear seat inner with center belt assembly LH installed.


i.

With the belt installed, check that the belt locks when it is pulled out quickly.

If the operation is not as specified, replace the rear seat inner with center belt assembly LH.



e.

Remove the bolt to disconnect the floor anchor part of the front seat outer belt assembly.


Hide 64274 3.INSTALL NO. 1 ROOM PARTITION TRIM PAD (for Sedan)

Hide 64330D 4.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Sedan)

Hide 62472A 5.INSTALL ROOF SIDE INNER GARNISH LH (for Sedan)

Hide 62471A 6.INSTALL ROOF SIDE INNER GARNISH RH (for Sedan)

HINT:

Use the same procedure as for the LH side.


Hide 62552F 7.INSTALL REAR SEAT SIDE GARNISH LH (for Sedan)

Hide 62551F 8.INSTALL REAR SEAT SIDE GARNISH RH (for Sedan)

HINT:

Use the same procedure as for the LH side.


Hide 73370 9.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for Sedan)

Hide 73360 10.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for Sedan)

HINT:

Use the same procedure as for the LH side.


Hide 62332A 11.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Sedan)

a.

Connect the rear door opening trim weatherstrip LH.


Hide 62331A 12.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Sedan)

HINT:

Use the same procedure as for the LH side.


Hide 67918A 13.INSTALL REAR DOOR SCUFF PLATE LH (for TMT Made Sedan)

Hide 67917A 14.INSTALL REAR DOOR SCUFF PLATE RH (for TMT Made Sedan)

HINT:

Use the same procedure as for the LH side.


Hide 15.INSTALL REAR SEAT ASSEMBLY (for Sedan)

Hide 73480 17.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Hatchback)

a.

w/o Seat Belt Warning System:

i.
B345179C02
2.365,0.354 2.146,0.354 false 1.729,1.271 1.917,1.26 false 2.396,0.26 2.708,0.458 0.313,0.198 10 false *a 1.948,1.188 2.26,1.385 0.313,0.198 10 false *b
*a Convex
*b Arrow Mark


Install the rear seat inner with center belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:
·

Install the rear seat inner with center belt assembly LH with the arrow mark on the anchor part facing the front of the vehicle.

·

Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the convex of the floor panel.





b.

w/ Seat Belt Warning System:

i.
B345179C02
2.365,0.354 2.146,0.354 false 1.729,1.271 1.917,1.26 false 2.396,0.26 2.708,0.458 0.313,0.198 10 false *a 1.948,1.188 2.26,1.385 0.313,0.198 10 false *b
*a Convex
*b Arrow Mark


Install the rear seat inner with center belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:
·

Install the rear seat inner with center belt assembly LH with the arrow mark on the anchor part facing the front of the vehicle.

·

Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the convex of the floor panel.




ii.

Connect the connector.


iii.

Install the wiring harness protector.



Hide 18.INSTALL REAR SEAT CUSHION ASSEMBLY (for Hatchback)