Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0092579 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:

The procedure described below is for the LH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


PROCEDURE

Hide 73220 1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Check the angle of inclination required to lock the retractor.

i.
B131510C10
2.406,0.063 2.813,0.354 0.406,0.292 10 false *a 0.219,1.094 0.573,1.323 0.354,0.229 10 false *b 0.875,0.208 1.198,0.469 0.323,0.26 10 false 45°
*a Unlock
*b Lock


Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

NOTICE:

Do not disassemble the retractor.


If the operation is not as specified, replace the front seat outer belt assembly.



Hide 73200A 2.INSTALL FRONT SHOULDER BELT ADJUSTER ANCHOR ASSEMBLY (for TMT Made)

a.
B487715E01
2.823,0.49 3.073,0.49 false 2.917,1.823 3.167,1.823 false 3.125,0.406 3.281,0.604 0.156,0.198 10 false b 3.229,1.719 3.385,1.917 0.156,0.198 10 false a

Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Fully tighten the bolt (a) first, then the bolt (b).

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B346961N01
1.292,0.333 1.646,0.604 0.354,0.271 10 false A 2.208,2.938 2.417,3.125 0.208,0.188 10 true B

Engage the 2 hooks and temporarily install the retractor of the front seat outer belt assembly with the 2 bolts.


b.

Tighten bolt A and then bolt B.

i.

for TMT Made:

Torque:
for Bolt A : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)


ii.

for TMMIN Made:

Torque:
for Bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for Bolt B : 42 N*m (428 kgf*cm, 31 ft.*lbf)



c.
B346962C01
0.615,2.792 1,2.833 true 1.042,2.76 1.375,3.052 0.333,0.292 10 false *1
*1 Locking Button


w/ Pretensioner and Force Limiter:

i.

Connect the pretensioner connector.


ii.

Lock the locking button.

NOTICE:

Securely lock the locking button.




d.

for TMT Made:

i.

Install the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



e.

for TMMIN Made:

i.

Install the shoulder anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



f.

Install the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Check that the ELR locks.

NOTICE:
·

The check should be performed with the front seat outer belt assembly installed.

·

Do not allow the anchor of the front seat outer belt assembly and the protruding parts of the floor panel to overlap.



i.

With the belt installed, check that the belt locks when it is pulled out quickly. If the operation is not as specified, replace the front seat outer belt assembly.



h.

Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.


Hide 73220 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Install the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62332A 7.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the rear door opening trim weatherstrip.


Hide 67917A 8.INSTALL REAR DOOR SCUFF PLATE (for TMT Made)

Hide 62312B 9.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the front door opening trim weatherstrip.


Hide 67913 10.INSTALL FRONT DOOR SCUFF PLATE (for TMT Made)

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Pretensioner and Force Limiter)

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.INSPECT SRS WARNING LIGHT (w/ Pretensioner and Force Limiter)