Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY(for Sedan) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0092582 REAR SEAT OUTER BELT ASSEMBLY(for Sedan) A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY(for Sedan)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The procedure described below is for the LH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


PROCEDURE

Hide 73143 1.INSTALL SEAT BELT HOLE SEAL

a.

Engage the 2 claws to install the seat belt hole seal.


Hide 73360 2.INSPECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

a.
B279526C12
0.469,0.594 0.708,0.865 0.24,0.271 10 false *a 1.198,1.927 1.438,2.135 0.24,0.208 10 false *b 0.75,1.302 1.031,1.531 0.281,0.229 10 false 45°
*a Unlock
*b Lock


Check the angle of inclination required to lock the retractor.

i.

Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.

NOTICE:

Do not disassemble the retractor.


If the operation is not as specified, replace the rear seat outer belt assembly.



Hide 73360 3.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

a.

Engage the guide to install the rear seat 3 point type outer belt assembly.


b.

Install the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.

Engage the 2 claws at seat belt hole seal to connect the floor anchor of the rear 3 point type outer belt assembly.


d.

Install the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Check that the ELR locks.

NOTICE:

Perform the check with the rear seat 3 point type outer belt assembly installed.


i.

With the belt installed, check that the belt locks when it is pulled out quickly.

If the operation is not as specified, replace the rear seat 3 point type outer belt assembly.



f.

Remove the bolt.


g.

Disengage the 2 claws to disconnect the floor anchor of the rear 3 point type outer belt assembly.


Hide 64272B 4.INSTALL ROOM PARTITION BOARD LH (for Separate Seat Type)

Hide 64274 5.INSTALL NO. 1 ROOM PARTITION TRIM PAD (for Separate Seat Type)

Hide 64330D 6.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 62471A 8.INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62551F 10.INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73370 11.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 73360 12.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 13.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Connect the rear door opening trim weatherstrip LH.


Hide 62331A 14.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67918A 15.INSTALL REAR DOOR SCUFF PLATE LH (for TMT Made)

Hide 67917A 16.INSTALL REAR DOOR SCUFF PLATE RH (for TMT Made)

HINT:

Use the same procedure as for the LH side.


Hide 17.INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)

Hide 18.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)