Make sure to release the vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
28800
4.REMOVE BATTERY
74431
5.REMOVE BATTERY TRAY
74410
6.REMOVE BATTERY CARRIER ASSEMBLY
31434C
7.DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)
Loosen the hose clip and disconnect the clutch reservoir tube from the brake master cylinder sub-assembly.
47201
8.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)
The brake master cylinder sub-assembly requires careful handling. Do not allow the brake master cylinder sub-assembly to receive any impact, such as from being dropped. Do not reuse a brake master cylinder sub-assembly that has been dropped.
Do not pull out the master cylinder piston.
Do not strike or pinch the master cylinder piston and do not cause any damage to the master cylinder piston by any other means.
When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.
Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the master cylinder piston.
Do not use any other type of grease or fluid.
Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the front No. 1 brake tube way.
Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Disengage the wire harness clamp.
Disconnect the brake fluid level warning switch connector.
Disengage the wire harness clamp.
Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the brake master cylinder sub-assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
Remove the O-ring from the brake master cylinder sub-assembly.
47201
9.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ VSC)
The brake master cylinder sub-assembly requires careful handling. Do not allow the brake master cylinder sub-assembly to receive any impact, such as from being dropped. Do not reuse a brake master cylinder sub-assembly that has been dropped.
Do not pull out the master cylinder piston.
Do not strike or pinch the master cylinder piston and do not cause any damage to the master cylinder piston by any other means.
When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.
Do not allow any foreign objects to contaminate the master cylinder piston. If a foreign object gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap based glycol grease around the circumference (sliding part) of the master cylinder piston.
Do not use any other type of grease or fluid.
Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the front No. 1 brake tube way.
Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Disengage the wire harness clamp.
Disconnect the brake fluid level warning switch connector.
Disengage the wire harness clamp.
Using a 12 mm union nut wrench, disconnect the 2 brake tubes from the brake master cylinder sub-assembly.
Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.
Remove the O-ring from the brake master cylinder sub-assembly.