1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.DRAIN MANUAL TRANSAXLE OIL
12262
4.DISCONNECT NO. 2 VENTILATION HOSE
17880
5.REMOVE AIR CLEANER HOSE ASSEMBLY
6.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17801
7.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
8.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
9.REMOVE BATTERY
74431
10.REMOVE BATTERY TRAY
74410
11.REMOVE BATTERY CARRIER ASSEMBLY
33820B
12.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the 2 clips A and 2 washers to disconnect the transmission control cable assembly from the manual transaxle assembly.
Remove the 2 clips B to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.
82121
13.DISCONNECT ENGINE WIRE
Disconnect the connector from the back-up light switch assembly.
Disconnect the connector from the oxygen sensor.
Remove the bolt A to separate the engine wire from the manual transaxle assembly.
Disengage the 7 clamps to separate the engine wire from the wire harness clamp brackets.
Remove the bolt B and wire harness clamp bracket from the manual transaxle assembly.
31470
14.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY
Remove the clip.
Remove the 2 bolts A to separate the clutch release cylinder to flexible hose tube from the manual transaxle assembly.
Remove the 2 bolts B to separate the clutch release cylinder assembly from the manual transaxle assembly.
Suspend the clutch release cylinder assembly with a piece of rope so as not to place stress on the clutch line.
Do not depress the clutch pedal.
57533B
15.REMOVE FRONT FLOOR CENTER BRACE
17410
16.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43498A
17.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR
18.REMOVE FRONT DRIVE SHAFT ASSEMBLIES
28100
19.REMOVE STARTER ASSEMBLY
51201
20.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
21.SUPPORT ENGINE ASSEMBLY
Remove the 4 bolts from the engine assembly side.
| *a | Height Adjustment Attachments |
| *b | Plate Lift Attachment |
| *c | Engine Lifter |
|
Attachment Placement Position |
Place the height adjustment attachments and plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.
Place the height adjustment attachments and plate lift attachments so that the engine assembly with the manual transaxle assembly is level.
As the engine assembly with the manual transaxle assembly is very heavy, be sure to support it securely.
12313
22.REMOVE ENGINE MOVING CONTROL ROD BRACKET
Remove the 4 bolts and engine moving control rod bracket from the manual transaxle assembly.
30300
23.REMOVE MANUAL TRANSAXLE ASSEMBLY
Set the transmission jack underneath the manual transaxle assembly.
Secure the manual transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.
Remove the bolt and nut to separate the engine mounting insulator LH from the engine mounting bracket LH.
Turn the bolt while holding the nut.
Remove the 5 bolts.
Disengage the hook to remove the engine mounting insulator LH from the body.
Remove the 5 bolts and engine mounting bracket LH from the manual transaxle assembly.
| *1 | Engine Assembly |
| *2 | Manual Transaxle Assembly |
| *a | Body |
| *b | Tilt 50 mm (1.97 in.) or less |
|
Watch for Interference |
Operate the engine lifter and transmission jack, and slowly tilt the engine assembly with the manual transaxle assembly 50 mm (1.97 in.) or less.
Do not allow the engine assembly and manual transaxle assembly to interfere with the body.
Make sure that the engine assembly is not tilted more than necessary.
Make sure that the wire harness and hoses are not being pulled.
Remove the 4 bolts from the manual transaxle assembly side.
| *1 | Clutch Disc Assembly |
| *2 | Clutch Cover Assembly |
| *3 | Input Shaft |
|
Watch for Interference |
Using the transmission jack, remove the manual transaxle assembly from the engine assembly according to the procedures shown in the illustration.
To prevent damage to the knock pins, do not pry between the manual transaxle assembly and engine assembly.
To prevent damage to the input shaft, do not forcefully shake the manual transaxle assembly.
Make sure the manual transaxle assembly does not interfere with the clutch tube or other components.
Move the manual transaxle assembly towards the left side of the vehicle and disengage the input shaft from the clutch disc assembly.
Tilt the manual transaxle assembly and pull the input shaft out from the clutch cover assembly.
Lower the manual transaxle assembly.
24.REMOVE WIRE HARNESS CLAMP BRACKET
Remove the 3 bolts and 3 wire harness clamp brackets from the manual transaxle assembly.
33403K
25.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
Remove the bolt and speedometer driven hole cover sub-assembly from the manual transaxle assembly.
Remove the O-ring from the speedometer driven hole cover sub-assembly.