Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271

DTC No. Detection Item DTC Detection Condition Trouble Area
C1405 Open or Short in Front Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH)

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1406 Open or Short in Front Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH)

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open FR speed sensor open detection Normal or Error Normal: Normal
Error: Momentary interruption
-
FL Speed Open FL speed sensor open detection Normal or Error Normal: Normal
Error: Momentary interruption
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed FR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
FL Wheel Speed FL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly with front speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1405 and C1406) are not output A
DTCs (C1405 and/or C1406) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A35*1 or A47*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



d.

Disconnect the A14*3 or A13*4 front speed sensor connector.

*3: for RH

*4: for LH



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A35-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A35-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A35-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A35-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A47-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A47-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A47-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A47-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for LH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A35-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A35-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A35-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A35-18 (FL-) or A13-1 (FL-) - Body ground Always 10 kΩ or higher

for LH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A47-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A47-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A47-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A47-18 (FL-) - A13-1 (FL-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C280123C23
2.344,0.354 2.76,0.625 0.417,0.271 0.76,0.354 1.177,0.625 0.417,0.271 1.375,1.75 1.063,1.24 true 2.958,1.75 2.646,1.24 true 0.854,0.406 1.198,0.615 0.344,0.208 10 false A14 2.438,0.406 2.781,0.615 0.344,0.208 10 false A13 0.135,0.156 0.323,0.354 0.188,0.198 10 false *a 1.302,0.396 1.521,0.542 0.219,0.146 10 false *b 2.875,0.385 3.052,0.573 0.177,0.188 10 false *c 1.417,1.698 1.719,1.896 0.302,0.198 10 false FR+ 3,1.708 3.302,1.906 0.302,0.198 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor)
*b for RH
*c for LH


Reconnect the A35*1 or A47*2 skid control ECU (brake actuator assembly) connector.

*1: Except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A14-2 (FR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A13-2 (FL+) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Check the speed sensor signal after repair or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

NG