Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273

DTC No. Detection Item DTC Detection Condition Trouble Area
C1407 Open or Short in Rear Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Skid control sensor wire RH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)


C1408 Open or Short in Rear Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Skid control sensor wire LH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Open RR speed sensor open detection Normal or Error Normal: Normal
Error: Momentary interruption
-
RL Speed Open RL speed sensor open detection Normal or Error Normal: Normal
Error: Momentary interruption
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Speed Open
RL Speed Open
50003 105 202,203
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (REAR SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING GTS (REAR SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed RR wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
RL Wheel Speed RL wheel speed sensor reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
0 km/h: Vehicle stopped When driving at constant speed:
No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 105 3,4

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly. If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly with rear speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.


d.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs (C1407 and C1408) are not output A
DTCs (C1407 and/or C1408) are output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



A

B

4.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control sensor wire connectors.


d.
C280125C12
0.823,0.49 1.167,0.667 0.344,0.177 0.823,0.74 1.167,0.917 0.344,0.177 2.167,0.5 2.583,0.677 0.417,0.177 2.167,0.75 2.583,0.927 0.417,0.177 0.948,1.542 0.667,2.396 true 1.104,1.552 1.333,2.385 true 2.333,1.667 2.083,2.385 true 2.5,1.667 2.823,2.375 true 0.135,0.125 0.323,0.323 0.188,0.198 10 false *a 0.917,0.5 1.167,0.667 0.25,0.167 10 false P1 0.917,0.75 1.156,0.917 0.24,0.167 10 false O1 2.25,0.75 2.583,0.917 0.333,0.167 10 false OF1 0.5,2.417 1,2.583 0.5,0.167 10 false RR- *b 1.25,0.75 1.438,0.917 0.188,0.167 10 false *c 2.667,0.75 2.833,0.917 0.167,0.167 10 false *c 2.646,0.5 2.833,0.667 0.188,0.167 10 false *b 1.25,0.5 1.438,0.667 0.188,0.167 10 false *b 2.25,0.5 2.583,0.667 0.333,0.167 10 false PF1 0.5,2.583 1,2.75 0.5,0.167 10 false RL- *c 1.167,2.417 1.667,2.583 0.5,0.167 10 false RR+ *b 1.167,2.583 1.667,2.75 0.5,0.167 10 false RL+ *c 1.917,2.417 2.417,2.583 0.5,0.167 10 false RR+ *b 1.917,2.583 2.417,2.75 0.5,0.167 10 false RL+ *c 2.667,2.417 3.167,2.583 0.5,0.167 10 false RR- *b 2.667,2.583 3.167,2.75 0.5,0.167 10 false RL- *c
*a Component without harness connected
(Skid Control Sensor Wire)
*b for RH
*c for LH


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
P1-2 (RR+) - PF1-1 (RR+) Always Below 1 Ω
P1-1 (RR-) - PF1-2 (RR-) Always Below 1 Ω
P1-2 (RR+) - PF1-2 (RR-) Always 10 kΩ or higher
P1-2 (RR+) or PF1-1 (RR+) - Body ground Always 10 kΩ or higher
P1-1 (RR-) - PF1-1 (RR+) Always 10 kΩ or higher
P1-1 (RR-) or PF1-2 (RR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
O1-2 (RL+) - OF1-1 (RL+) Always Below 1 Ω
O1-1 (RL-) - OF1-2 (RL-) Always Below 1 Ω
O1-2 (RL+) - OF1-2 (RL-) Always 10 kΩ or higher
O1-2 (RL+) or OF1-1 (RL+) - Body ground Always 10 kΩ or higher
O1-1 (RL-) - OF1-1 (RL+) Always 10 kΩ or higher
O1-1 (RL-) or OF1-2 (RL-) - Body ground Always 10 kΩ or higher



NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


e.

Reconnect the skid control sensor wire connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A35*1 or A47*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



d.

Disconnect the P1*3 or O1*4 rear speed sensor connector.

*3: for RH

*4: for LH



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A35-17 (RR+) - P1-2 (RR+) Always Below 1 Ω
A35-17 (RR+) or P1-2 (RR+) - Body ground Always 10 kΩ or higher
A35-16 (RR-) - P1-1 (RR-) Always Below 1 Ω
A35-16 (RR-) or P1-1 (RR-) - Body ground Always 10 kΩ or higher

for RH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A47-17 (RR+) - P1-2 (RR+) Always Below 1 Ω
A47-17 (RR+) or P1-2 (RR+) - Body ground Always 10 kΩ or higher
A47-16 (RR-) - P1-1 (RR-) Always Below 1 Ω
A47-16 (RR-) or P1-1 (RR-) - Body ground Always 10 kΩ or higher

for LH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A35-5 (RL+) - O1-2 (RL+) Always Below 1 Ω
A35-5 (RL+) or O1-2 (RL+) - Body ground Always 10 kΩ or higher
A35-4 (RL-) - O1-1 (RL-) Always Below 1 Ω
A35-4 (RL-) or O1-1 (RL-) - Body ground Always 10 kΩ or higher

for LH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A47-5 (RL+) - O1-2 (RL+) Always Below 1 Ω
A47-5 (RL+) or O1-2 (RL+) - Body ground Always 10 kΩ or higher
A47-4 (RL-) - O1-1 (RL-) Always Below 1 Ω
A47-4 (RL-) or O1-1 (RL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR INPUT)
a.
C280123C24
0.76,0.365 1.198,0.604 0.438,0.24 2.344,0.375 2.781,0.615 0.438,0.24 1.344,1.729 1.063,1.24 true 2.917,1.719 2.646,1.24 true 1.292,0.396 1.49,0.594 0.198,0.198 10 false *b 0.875,0.406 1.094,0.604 0.219,0.198 10 false P1 2.469,0.406 2.688,0.594 0.219,0.188 10 false O1 2.875,0.385 3.073,0.583 0.198,0.198 10 false *c 0.115,0.104 0.313,0.302 0.198,0.198 10 false *a 2.979,1.677 3.313,1.865 0.333,0.188 10 false RL+ 1.417,1.698 1.75,1.885 0.333,0.188 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor)
*b for RH
*c for LH


Reconnect the A35*1 or A47*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
P1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
O1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Result Proceed to
OK (for Rear Disc Brake) A
OK (for Rear Drum Brake) B
NG C



A

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

C