Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271

DTC No. Detection Item DTC Detection Condition Trouble Area
C1405 Open or Short in Front Speed Sensor RH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector


C1406 Open or Short in Front Speed Sensor LH Circuit Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor LH

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Normal or Error Normal Error: Momentary interruption
FL Speed Open Front speed sensor LH open detection Normal or Error Normal Error: Momentary interruption
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

Normal (There are no momentary interruptions.)


HINT:

Perform the above inspection before removing the sensor and connector.


Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

2.READ VALUE USING GTS (FRONT SPEED SENSOR)

B

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

C

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
2.READ VALUE USING GTS (FRONT SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326.4 km/h (202 mph)
Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2
f.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


HINT:
·

The front speed sensor rotor is incorporated into the front axle hub sub-assembly. If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub sub-assembly with front speed sensor.

·

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

3.RECONFIRM DTC

B

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)

C

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
3.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1405 and C1406 are not output A
DTCs C1405 and/or C1406 are output B



A

B

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector and the A14 and/or A13 front speed sensor connectors.

*1: for Manual Transaxle

*2: for Continuously Variable Transaxle



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (for Manual Transaxle)
Tester Connection Condition Specified Condition
A48-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A48-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A48-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A48-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (for Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A49-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A49-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A49-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for LH (for Manual Transaxle)
Tester Connection Condition Specified Condition
A48-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A48-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A48-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A48-18 (FL-) or A13-1 (FL-) - Body ground Always 10 kΩ or higher

for LH (for Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A49-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A49-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A49-18 (FL-) or A13-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.
C280123C33
2.344,0.354 2.76,0.625 0.417,0.271 0.76,0.354 1.177,0.625 0.417,0.271 1.375,1.75 1.063,1.24 true 2.958,1.75 2.646,1.24 true 0.854,0.406 1.198,0.615 0.344,0.208 10 false A14 2.438,0.406 2.781,0.615 0.344,0.208 10 false A13 0.135,0.156 0.323,0.354 0.188,0.198 10 false *a 1.302,0.396 1.521,0.542 0.219,0.146 10 false *b 2.875,0.385 3.052,0.573 0.177,0.188 10 false *c 1.417,1.698 1.719,1.896 0.302,0.198 10 false FR+ 3,1.708 3.302,1.906 0.302,0.198 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor)
*b for RH
*c for LH


Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: for Manual Transaxle

*2: for Continuously Variable Transaxle



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A14-2 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A13-2 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector and the A14 and/or A13 front speed sensor connectors.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A48-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A48-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A48-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A48-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for RH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-7 (FR+) - A14-2 (FR+) Always Below 1 Ω
A49-6 (FR-) - A14-1 (FR-) Always Below 1 Ω
A49-7 (FR+) or A14-2 (FR+) - Body ground Always 10 kΩ or higher
A49-6 (FR-) or A14-1 (FR-) - Body ground Always 10 kΩ or higher

for LH (except LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A48-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A48-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A48-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A48-18 (FL-) or A13-1 (FL-) - Body ground Always 10 kΩ or higher

for LH (for LHD with Continuously Variable Transaxle)
Tester Connection Condition Specified Condition
A49-19 (FL+) - A13-2 (FL+) Always Below 1 Ω
A49-18 (FL-) - A13-1 (FL-) Always Below 1 Ω
A49-19 (FL+) or A13-2 (FL+) - Body ground Always 10 kΩ or higher
A49-18 (FL-) or A13-1 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR OUTPUT)
a.
C280123C33
2.344,0.354 2.76,0.625 0.417,0.271 0.76,0.354 1.177,0.625 0.417,0.271 1.375,1.75 1.063,1.24 true 2.958,1.75 2.646,1.24 true 0.854,0.406 1.198,0.615 0.344,0.208 10 false A14 2.438,0.406 2.781,0.615 0.344,0.208 10 false A13 0.135,0.156 0.323,0.354 0.188,0.198 10 false *a 1.302,0.396 1.521,0.542 0.219,0.146 10 false *b 2.875,0.385 3.052,0.573 0.177,0.188 10 false *c 1.417,1.698 1.719,1.896 0.302,0.198 10 false FR+ 3,1.708 3.302,1.906 0.302,0.198 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor)
*b for RH
*c for LH


Reconnect the A48*1 or A49*2 skid control ECU (brake actuator assembly) connector.

*1: except LHD with Continuously Variable Transaxle

*2: for LHD with Continuously Variable Transaxle



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Switch Condition Specified Condition
A14-2 (FR+) - Body ground Ignition switch ON 8 to 14 V

for LH
Tester Connection Switch Condition Specified Condition
A13-2 (FL+) - Body ground Ignition switch ON 8 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE FRONT AXLE HUB SUB-ASSEMBLY

NG