Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, a short in a turn signal light circuit, or a short in the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

Bulb

·

Harness or connector

·

No. 6 junction connector*1

·

Driver side junction block assembly*2

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

Bulb

·

Harness or connector

·

No. 6 junction connector*1

·

Driver side junction block assembly*2

·

Combination meter assembly


DTC stored -

*1: for TMMIN Made

*2: for TMT Made


WIRING DIAGRAM

for TMMIN Made


E270878E10
1.333,0.646 1.677,0.833 0.344,0.188 10 false A12 1.333,0.802 3.302,1.083 1.969,0.281 10 false Headlight Assembly LH 1.333,1.719 2.615,1.948 1.281,0.229 10 false F25 1.333,1.885 3.74,2.104 2.406,0.219 10 false Rear Combination Light Assembly LH 1.333,2.865 1.792,3.063 0.458,0.198 10 false H6 1.333,3.021 3.75,3.333 2.417,0.313 10 false Outer Rear View Mirror Assembly LH*1 1.333,8.094 1.792,8.292 0.458,0.198 10 false A16 1.333,4 3.75,4.271 2.417,0.271 10 false Side Turn Signal Light Assembly LH*2 1.333,5.031 3.76,5.281 2.427,0.25 10 false Headlight Assembly RH 1.333,4.875 2.302,5.073 0.969,0.198 10 false A11 1.333,7.094 1.792,7.292 0.458,0.198 10 false G6 1.333,7.26 3.76,7.583 2.427,0.323 10 false Outer Rear View Mirror Assembly RH*1 1.75,6.688 2.208,6.885 0.458,0.198 10 false E 1.583,6.677 2.042,6.875 0.458,0.198 10 false 6 2.625,6.698 3.083,6.896 0.458,0.198 10 false B 2.802,6.688 3.26,6.885 0.458,0.198 10 false 10 2.625,5.583 3.083,5.781 0.458,0.198 10 false B 1.75,5.573 2.208,5.771 0.458,0.198 10 false E 1.76,4.448 2.219,4.646 0.458,0.198 10 false E 1.573,4.448 2.031,4.646 0.458,0.198 10 false 1 2.625,4.448 3.083,4.646 0.458,0.198 10 false B 2.823,4.448 3.281,4.646 0.458,0.198 10 false 2 2.802,2.448 3.26,2.646 0.458,0.198 10 false 10 2.615,2.448 3.073,2.646 0.458,0.198 10 false B 1.76,2.458 2.219,2.656 0.458,0.198 10 false E 1.594,2.448 2.052,2.646 0.458,0.198 10 false 6 1.76,1.313 2.219,1.51 0.458,0.198 10 false E 2.604,1.313 3.063,1.51 0.458,0.198 10 false B 2.823,0.229 3.281,0.427 0.458,0.198 10 false 2 2.615,0.24 3.073,0.438 0.458,0.198 10 false B 1.563,0.24 2.021,0.438 0.458,0.198 10 false 1 1.75,0.24 2.208,0.438 0.458,0.198 10 false E 4.25,0.094 4.708,0.292 0.458,0.198 10 false 16 4.219,4.542 4.677,4.74 0.458,0.198 10 false F68 4.25,5.469 4.708,5.667 0.458,0.198 10 false 10 4.219,1.385 4.677,1.583 0.458,0.198 10 false F69 4.26,2.354 4.719,2.552 0.458,0.198 10 false 18 4.229,6.771 4.688,6.969 0.458,0.198 10 false F69 4.292,4.365 4.75,4.563 0.458,0.198 10 false 1 4.219,0.313 4.677,0.51 0.458,0.198 10 false F68 4.25,1.188 4.708,1.385 0.458,0.198 10 false 17 4.229,2.521 4.688,2.719 0.458,0.198 10 false F68 5.104,4.531 5.563,4.729 0.458,0.198 10 false F68 5.188,4.344 5.646,4.542 0.458,0.198 10 false 2 5.104,0.313 5.563,0.51 0.458,0.198 10 false F68 5.135,0.094 5.594,0.292 0.458,0.198 10 false 17 4.219,5.656 4.677,5.854 0.458,0.198 10 false F69 5.865,0.24 6.323,0.438 0.458,0.198 10 false 13 6.125,0.323 6.583,0.521 0.458,0.198 10 false LL 5.927,4.448 6.385,4.646 0.458,0.198 10 false 7 6.125,4.552 6.583,4.75 0.458,0.198 10 false LR 5.927,7.229 6.385,7.427 0.458,0.198 10 false F39 5.927,7.406 7.094,8.094 1.167,0.688 10 false Combination Meter Assembly 4.094,7.25 5.823,7.635 1.729,0.385 10 false No. 6 Junction Connector 1.333,3.833 1.792,4.031 0.458,0.198 10 false A15 1.333,8.26 3.729,8.594 2.396,0.333 10 false Side Turn Signal Light Assembly RH*2 0.083,9.156 3.583,9.583 3.5,0.427 10 false *1: for Outer Rear View Mirror Type Side Turn Signal Light 0.094,9.521 3.01,9.875 2.917,0.354 10 false *2: for Front Fender Type Side Turn Signal Light 1.323,6.135 3.792,6.385 2.469,0.25 10 false Rear Combination Light Assembly RH 1.333,5.99 2.958,6.208 1.625,0.219 10 false F26 2.031,3.5 2.49,3.698 0.458,0.198 10 false 2 2.375,3.5 2.833,3.698 0.458,0.198 10 false 1 2,7.729 2.458,7.927 0.458,0.198 10 false 2 2.427,7.729 2.885,7.927 0.458,0.198 10 false 1 4.25,6.573 4.708,6.771 0.458,0.198 10 false 11 1.552,1.302 1.698,1.49 0.146,0.188 10 false 4 2.844,1.292 3.302,1.49 0.458,0.198 10 false 5 1.583,5.573 1.75,5.76 0.167,0.188 10 false 4 2.823,5.563 2.969,5.771 0.146,0.208 10 false 5


for TMT Made


E376669E01
1.573,0.208 1.729,0.406 0.156,0.198 10 false 1 2.865,0.208 3.021,0.406 0.156,0.198 10 false 2 2.635,0.208 2.792,0.406 0.156,0.198 10 false B 2.625,1.323 2.781,1.521 0.156,0.198 10 false B 2.615,2.448 2.771,2.646 0.156,0.198 10 false B 2.604,3.542 2.76,3.74 0.156,0.198 10 false B 2.615,4.646 2.771,4.844 0.156,0.198 10 false B 2.615,5.76 2.771,5.958 0.156,0.198 10 false B 2.625,6.865 2.781,7.063 0.156,0.198 10 false B 2.615,7.969 2.771,8.167 0.156,0.198 10 false B 1.802,0.219 1.958,0.417 0.156,0.198 10 false E 1.792,1.333 1.948,1.531 0.156,0.198 10 false E 1.802,2.427 1.958,2.625 0.156,0.198 10 false E 1.802,3.542 1.958,3.74 0.156,0.198 10 false E 1.792,4.646 1.948,4.844 0.156,0.198 10 false E 1.802,5.75 1.958,5.948 0.156,0.198 10 false E 1.792,6.865 1.948,7.063 0.156,0.198 10 false E 1.792,7.969 1.948,8.167 0.156,0.198 10 false E 2.865,4.635 3.021,4.833 0.156,0.198 10 false 2 1.583,4.635 1.74,4.833 0.156,0.198 10 false 1 2.948,1.24 3.104,1.438 0.156,0.198 10 false 5 3.333,1.24 3.49,1.438 0.156,0.198 10 false 4 1.115,1.229 1.271,1.427 0.156,0.198 10 false 4 1.5,1.229 1.656,1.427 0.156,0.198 10 false 3 1.083,1.625 1.24,1.823 0.156,0.198 10 false *3 1.458,1.625 1.615,1.823 0.156,0.198 10 false *4 3.302,1.625 3.458,1.823 0.156,0.198 10 false *4 2.917,1.625 3.073,1.823 0.156,0.198 10 false *3 2.865,1.417 3.188,1.583 0.323,0.167 10 false F25 3.208,1.417 3.604,1.604 0.396,0.188 10 false F179 1.385,1.417 1.781,1.604 0.396,0.188 10 false F179 1.021,1.417 1.344,1.583 0.323,0.167 10 false F25 2.135,0.5 2.531,0.688 0.396,0.188 10 false Turn 2.146,1.594 2.542,1.781 0.396,0.188 10 false Turn 2.135,2.698 2.531,2.885 0.396,0.188 10 false Turn 2.125,3.813 2.521,4 0.396,0.188 10 false Turn 2.104,4.906 2.5,5.094 0.396,0.188 10 false Turn 2.115,6.021 2.51,6.208 0.396,0.188 10 false Turn 2.115,7.135 2.51,7.323 0.396,0.188 10 false Turn 2.115,8.24 2.51,8.427 0.396,0.188 10 false Turn 1.406,0.667 1.729,0.833 0.323,0.167 10 false A12 1.396,0.854 3.417,1.104 2.021,0.25 10 false Headlight Assembly LH 1.448,5.104 1.771,5.271 0.323,0.167 10 false A11 1.448,5.271 3.469,5.521 2.021,0.25 10 false Headlight Assembly RH 1.094,1.969 3.906,2.24 2.813,0.271 10 false Rear Combination Light Assembly LH 1.094,6.448 3.906,6.719 2.813,0.271 10 false Rear Combination Light Assembly RH 2.927,6.042 3.083,6.24 0.156,0.198 10 false *3 3.302,6.052 3.458,6.25 0.156,0.198 10 false *4 1.49,6.052 1.646,6.25 0.156,0.198 10 false *4 1.083,6.052 1.24,6.25 0.156,0.198 10 false *3 1.031,5.833 1.354,6 0.323,0.167 10 false F26 1.385,5.833 1.781,6.021 0.396,0.188 10 false F180 3.219,5.833 3.615,6.021 0.396,0.188 10 false F180 2.865,5.833 3.188,6 0.323,0.167 10 false F26 3.323,5.667 3.479,5.865 0.156,0.198 10 false 4 1.115,5.667 1.271,5.865 0.156,0.198 10 false 4 1.521,5.656 1.677,5.854 0.156,0.198 10 false 3 2.948,5.677 3.104,5.875 0.156,0.198 10 false 5 4.281,0.302 4.677,0.49 0.396,0.188 10 false 6D 4.281,3.635 4.677,3.823 0.396,0.188 10 false 6D 4.281,2.521 4.677,2.708 0.396,0.188 10 false 6N 4.281,1.417 4.677,1.604 0.396,0.188 10 false 6N 5.156,0.313 5.552,0.5 0.396,0.188 10 false 6N 4.292,4.74 4.688,4.927 0.396,0.188 10 false 6E 5.156,4.729 5.552,4.917 0.396,0.188 10 false 6H 4.281,5.844 4.677,6.031 0.396,0.188 10 false 6K 4.281,6.948 4.677,7.135 0.396,0.188 10 false 6K 4.281,8.052 4.677,8.24 0.396,0.188 10 false 6C 4.323,7.865 4.719,8.052 0.396,0.188 10 false 6 4.323,6.75 4.719,6.938 0.396,0.188 10 false 4 4.323,5.646 4.719,5.833 0.396,0.188 10 false 6 4.323,4.542 4.719,4.729 0.396,0.188 10 false 4 5.198,4.531 5.594,4.719 0.396,0.188 10 false 8 6.167,4.74 6.563,4.927 0.396,0.188 10 false LR 5.958,4.635 6.354,4.823 0.396,0.188 10 false 7 6.167,0.313 6.563,0.5 0.396,0.188 10 false LL 5.885,0.219 6.281,0.406 0.396,0.188 10 false 13 5.198,0.125 5.594,0.313 0.396,0.188 10 false 7 4.323,0.125 4.719,0.313 0.396,0.188 10 false 8 4.333,1.219 4.729,1.406 0.396,0.188 10 false 8 4.281,2.344 4.677,2.531 0.396,0.188 10 false 10 4.281,3.448 4.677,3.635 0.396,0.188 10 false 10 1.01,3.094 3.823,3.365 2.813,0.271 10 false Outer Rear View Mirror Assembly LH*1 1.031,2.938 1.427,3.125 0.396,0.188 10 false H6 2.823,2.438 3.219,2.625 0.396,0.188 10 false 10 1.583,2.427 1.979,2.615 0.396,0.188 10 false 6 2.854,3.531 3.01,3.729 0.156,0.198 10 false 1 1.573,3.531 1.729,3.729 0.156,0.198 10 false 2 1.563,7.969 1.719,8.167 0.156,0.198 10 false 2 2.865,7.958 3.021,8.156 0.156,0.198 10 false 1 2.833,6.854 3.229,7.042 0.396,0.188 10 false 10 1.583,6.865 1.979,7.052 0.396,0.188 10 false 6 1.073,7.531 3.885,7.802 2.813,0.271 10 false Outer Rear View Mirror Assembly RH*1 1.073,7.365 1.469,7.552 0.396,0.188 10 false G6 1.083,4.01 1.479,4.198 0.396,0.188 10 false A15 1.063,4.198 3.875,4.469 2.813,0.271 10 false Side Turn Signal Light Assembly LH*2 1.083,8.604 3.896,8.875 2.813,0.271 10 false Side Turn Signal Light Assembly RH*2 1.094,8.438 1.49,8.625 0.396,0.188 10 false A16 3.698,8.396 6.167,8.667 2.469,0.271 10 false Driver Side Junction Block Assembly 5.917,7.719 7.115,8.167 1.198,0.448 10 false Combination Meter Assembly 5.927,7.563 6.323,7.75 0.396,0.188 10 false F39 0.135,9.052 3.823,9.333 3.688,0.281 10 false *1: for Outer Rear View Mirror Type Side Turn Signal Light 0.135,9.396 3.823,9.677 3.688,0.281 10 false *2: for Front Fender Type Side Turn Signal Light 4.094,9.052 5.417,9.365 1.323,0.313 10 false *3: for Sedan 4.094,9.396 6.271,9.708 2.177,0.313 10 false *4: for Hatchback


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the bulbs for this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMMIN Made A
for TFT Made B



A

2.INSPECT LIGHTS

B

9.INSPECT LIGHTS
2.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate (for Sedan). B
Rear turn signal light does not illuminate. C
Side turn signal light does not illuminate (for Outer Rear View Mirror Type Side Turn Signal Light). D
Side turn signal light does not illuminate (for Front Fender Type Side Turn Signal Light). E



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

B

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

C

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

D

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - NO. 6 JUNCTION CONNECTOR)

E

7.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the F39 combination meter assembly connector.


b.

Disconnect the F68 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F39-13 (LL) - F68-17 Always Below 1 Ω
F39-13 (LL) or F68-17 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F39-7 (LR) - F68-2 Always Below 1 Ω
F39-7 (LR) or F68-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the A12*1 or A11*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A12-2 (B) - F68-16 Always Below 1 Ω
A12-1 (E) - Body ground Always Below 1 Ω
A12-2 (B) or F68-16 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A11-2 (B) - F68-1 Always Below 1 Ω
A11-1 (E) - Body ground Always Below 1 Ω
A11-2 (B) or F68-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the F25*1 or F26*2 rear combination light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F69 No. 6 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
F25-5 (B) - F69-17 Always Below 1 Ω
F25-4 (E) - Body ground Always Below 1 Ω
F25-5 (B) or F69-17 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F26-5 (B) - F69-10 Always Below 1 Ω
F26-4 (E) - Body ground Always Below 1 Ω
F26-5 (B) or F69-10 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the H6*1 or G6*2 outer rear view mirror assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68*1 or F69*2 No. 6 junction connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
H6-10 (B) - F68-18 Always Below 1 Ω
H6-6 (E) - Body ground Always Below 1 Ω
H6-10 (B) or F68-18 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
G6-10 (B) - F69-11 Always Below 1 Ω
G6-8 (E) - Body ground Always Below 1 Ω
G6-10 (B) or F69-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the A15*1 or A16*2 side turn signal light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the F68*1 or F69*2 No. 6 junction connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
A15-1 - F68-18 Always Below 1 Ω
A15-2 - Body ground Always Below 1 Ω
A15-1 or F68-18 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
A16-1 - F69-11 Always Below 1 Ω
A16-2 - Body ground Always Below 1 Ω
A16-1 or F69-11 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 6 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT NO. 6 JUNCTION CONNECTOR
a.
E270875C05
0.125,1.063 0.5,1.229 0.375,0.167 0.125,1.313 0.5,1.479 0.375,0.167 0,0 0.313,0.156 0.313,0.156 10 false *a 0.198,1.063 0.583,1.229 0.385,0.167 10 false F68 0.208,1.313 0.604,1.479 0.396,0.167 10 false F69
*a Component without harness connected
(No. 6 Junction Connector)


Remove the No. 6 junction connector.


b.

Front turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F68-16 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F68-1 Always Below 1 Ω



c.

Rear turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F69-17 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F69-10 Always Below 1 Ω



d.

Side turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F68-17 - F68-18 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
F68-2 - F69-11 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 6 JUNCTION CONNECTOR

9.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
Turn signal lights for one side do not illuminate. A
Front turn signal light does not illuminate. B
Rear turn signal light does not illuminate (for Sedan). C
Rear turn signal light does not illuminate (for Hatchback). D
Side turn signal light does not illuminate (for Outer Rear View Mirror Type Side Turn Signal Light). E
Side turn signal light does not illuminate (for Front Fender Type Side Turn Signal Light). F



A

10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

B

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

C

12.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

D

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

E

14.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

F

15.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F39 combination meter assembly connector.


b.

Disconnect the 6N*1 or 6H*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F39-13 (LL) - 6N-7 Always Below 1 Ω
F39-13 (LL) or 6N-7 - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
F39-7 (LR) - 6H-8 Always Below 1 Ω
F39-7 (LR) or 6H-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A12*1 or A11*2 headlight assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 6D*1 or 6E*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A12-2 (B) - 6D-8 Always Below 1 Ω
A12-2 (B) or 6D-8 - Body ground Always 10 kΩ or higher
A12-1 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A11-2 (B) - 6E-4 Always Below 1 Ω
A11-2 (B) or 6E-4 - Body ground Always 10 kΩ or higher
A11-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F25*1 or F26*2 rear combination light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F25-5 (B) - 6N-8 Always Below 1 Ω
F25-5 (B) or 6N-8 - Body ground Always 10 kΩ or higher
F25-4 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
F26-5 (B) - 6K-6 Always Below 1 Ω
F26-5 (B) or 6K-6 - Body ground Always 10 kΩ or higher
F26-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F179*1 or F180*2 rear combination light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
F179-4 (B) - 6N-8 Always Below 1 Ω
F179-4 (B) or 6N-8 - Body ground Always 10 kΩ or higher
F179-3 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
F180-4 (B) - 6K-6 Always Below 1 Ω
F180-4 (B) or 6K-6 - Body ground Always 10 kΩ or higher
F180-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the H6*1 or G6*2 outer rear view mirror assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 6N*1 or 6K*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
H6-10 (B) - 6N-10 Always Below 1 Ω
H6-10 (B) or 6N-10 - Body ground Always 10 kΩ or higher
H6-6 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
G6-10 (B) - 6K-4 Always Below 1 Ω
G6-10 (B) or 6K-4 - Body ground Always 10 kΩ or higher
G6-6 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A15*1 or A16*2 side turn signal light assembly connector.

*1: for LH

*2: for RH



b.

Disconnect the 6D*1 or 6C*2 driver side junction block assembly connector.

*1: for LH

*2: for RH



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
A15-1 (B) - 6D-10 Always Below 1 Ω
A15-1 (B) or 6D-10 - Body ground Always 10 kΩ or higher
A15-2 (E) - Body ground Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
A16-1 (B) - 6C-6 Always Below 1 Ω
A16-1 (B) or 6C-6 - Body ground Always 10 kΩ or higher
A16-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL

E374197C01
0.5,0.333 0.917,0.583 0.417,0.25 1.698,0.333 2.115,0.583 0.417,0.25 2.844,0.333 3.26,0.583 0.417,0.25 4.021,0.333 4.438,0.583 0.417,0.25 5.188,0.333 5.604,0.583 0.417,0.25 6.281,0.333 6.698,0.583 0.417,0.25 0.115,0.104 0.427,0.323 0.313,0.219 10 false *a 0.625,0.375 0.938,0.594 0.313,0.219 10 false 6C 1.833,0.375 2.146,0.594 0.313,0.219 10 false 6D 2.979,0.375 3.292,0.594 0.313,0.219 10 false 6E 4.146,0.375 4.458,0.594 0.313,0.219 10 false 6H 5.313,0.385 5.625,0.604 0.313,0.219 10 false 6K 6.417,0.385 6.729,0.604 0.313,0.219 10 false 6N
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -



b.

Front turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
6N-7 - 6D-8 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
6H-8 - 6E-4 Always Below 1 Ω



c.

Rear turn signal light

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
6N-7 - 6N-8 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
6H-8 - 6K-6 Always Below 1 Ω



d.

Side turn signal light (for Outer Rear View Mirror Type Side Turn Signal Light)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
6N-7 - 6N-10 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
6H-8 - 6K-4 Always Below 1 Ω



e.

Side turn signal light (for Front Fender Type Side Turn Signal Light)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH
Tester Connection Condition Specified Condition
6N-7 - 6D-10 Always Below 1 Ω


for RH
Tester Connection Condition Specified Condition
6H-8 - 6C-6 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY