Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag ECU assembly and front seat outer belt assembly RH.

This circuit instructs SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1900/73 Short in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib RH circuit during primary check.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1901/73 Open in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly receives an open circuit signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1902/73 Short to GND in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC corresponds to check mode.
B1903/73 Short to B+ in Front Pretensioner Squib RH Circuit
·

The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib RH circuit.

·

Front pretensioner squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front seat outer belt assembly RH (Front pretensioner squib RH)

·

Airbag ECU assembly


DTC corresponds to check mode.

WIRING DIAGRAM

C389382E03
2.385,2.115 2.635,2.292 0.25,0.177 10 false R+ 2.698,2.104 2.948,2.281 0.25,0.177 10 false 1 2.427,2.938 2.635,3.115 0.208,0.177 10 false R- 2.698,2.938 2.948,3.115 0.25,0.177 10 false 2 4.313,1.948 4.583,2.125 0.271,0.177 10 false 2*1 4.313,2.125 4.583,2.302 0.271,0.177 10 false 4*2 4.656,2.219 5.01,2.427 0.354,0.208 10 false PR+ 4.656,3.01 5.01,3.219 0.354,0.208 10 false PR- 4.302,2.938 4.573,3.115 0.271,0.177 10 false 5*2 4.302,2.75 4.573,2.927 0.271,0.177 10 false 1*1 0.74,3.552 1.073,3.729 0.333,0.177 10 false F23 0.74,3.74 2.958,4.135 2.219,0.396 10 false Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH) 1.792,4.438 4.24,4.823 2.448,0.385 10 false *1: for TMT Made without Curtain Shield Airbag 1.792,5.031 4.438,5.427 2.646,0.396 10 false *2: for TMMIN Made and for TMT Made with Curtain Shield Airbag 4.74,4.698 5.75,4.906 1.01,0.208 10 false F22*1, F120*2 4.74,4.885 6.198,5.125 1.458,0.24 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C352089C02
1.552,1.385 1.833,0.833 false 1.563,3.875 1.833,3.333 false 0.333,3.875 0.583,3.333 false 0.333,1.385 0.604,0.833 false 0.188,0.167 0.563,0.406 0.375,0.24 12 false *A 0.177,2.667 1.073,2.969 0.896,0.302 12 false *B, *C 0.656,0.667 0.969,0.865 0.313,0.198 10 false *1 0.635,3.198 0.948,3.396 0.313,0.198 10 false *1 2.833,1.219 3.146,1.417 0.313,0.198 10 false *2 2.833,3.583 3.146,3.781 0.313,0.198 10 false *2 1.875,0.677 2.188,0.875 0.313,0.198 10 false *3 1.875,3.198 2.188,3.396 0.313,0.198 10 false *3 2.5,1.354 2.656,1.552 0.156,0.198 10 false A 2.5,3.854 2.656,4.052 0.156,0.198 10 false A 2.146,1.365 2.302,1.563 0.156,0.198 10 false B 2.146,3.865 2.302,4.063 0.156,0.198 10 false B 0.865,1.365 1.021,1.563 0.156,0.198 10 false C 0.865,3.865 1.021,4.063 0.156,0.198 10 false C 0.469,1.365 0.625,1.563 0.156,0.198 10 false D 0.469,3.865 0.625,4.063 0.156,0.198 10 false D
*A for TMT Made without Curtain Shield Airbag
*B for TMMIN Made
*C for TMT Made with Curtain Shield Airbag
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly
*3 Instrument panel wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the front seat outer belt assembly RH and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat outer belt assembly RH and airbag ECU assembly.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the instrument panel wire connector (on the front seat outer belt assembly RH side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Result Proceed to
OK (for TMT Made without Curtain Shield Airbag) A
OK (for TMMIN Made and for TMT Made with Curtain Shield Airbag) B
NG C



A

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)

B

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)

C

REPLACE INSTRUMENT PANEL WIRE

2.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
a.
C281409C01
0.448,2.333 0.781,2.573 0.333,0.24 1.802,2.313 2.125,2.229 false 0.667,1.458 0.688,1.094 false 0.823,0.958 1.021,1.146 0.198,0.188 10 false D 2.281,0.802 2.594,0.958 0.313,0.156 10 false *2 0.615,1.469 0.927,1.625 0.313,0.156 10 false *1 1.167,0.958 1.333,1.156 0.167,0.198 10 false C 0.5,3.417 0.813,3.573 0.313,0.156 10 false *3 0.323,1.927 0.635,2.083 0.313,0.156 10 false *a 0.49,2.365 0.948,2.563 0.458,0.198 10 false F23 2.167,2.125 2.625,2.323 0.458,0.198 10 false SST
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

3.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
3.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
C281410C01
0.656,2.271 1.031,2.51 0.375,0.24 1.406,1.063 1.083,0.51 false 0.563,1.51 0.677,1.208 false 1.083,2.115 1.406,2.271 true 1.615,2.26 1.875,2.104 true 0.813,1.052 0.969,1.25 0.156,0.198 10 false D 1.125,1.052 1.323,1.24 0.198,0.188 10 false C 0.885,0.417 1.115,0.604 0.229,0.188 10 false *3 0.417,1.51 0.729,1.667 0.313,0.156 10 false *1 2.323,0.896 2.635,1.052 0.313,0.156 10 false *2 1.573,1.052 1.719,1.25 0.146,0.198 10 false B 1.885,1.042 2.094,1.25 0.208,0.208 10 false A 0.26,1.823 0.573,1.979 0.313,0.156 10 false *a 0.729,2.302 1.188,2.5 0.458,0.198 10 false F23 0.885,2.031 1.198,2.229 0.313,0.198 10 false R+ 1.927,2.021 2.24,2.219 0.313,0.198 10 false R-
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly
*3 Instrument panel wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH (Front Pretensioner Squib RH))


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F23-1 (R+) - Body ground Ignition switch ON Below 1 V
F23-2 (R-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - F23-2 (R-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - Body ground Always 1 MΩ or higher
F23-2 (R-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - F23-2 (R-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

4.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK AIRBAG ECU ASSEMBLY
a.
C281411C01
1.115,1.948 0.833,1.448 false 0.969,1.292 1.167,1.5 0.198,0.208 10 false D 1.125,1.292 1.344,1.469 0.219,0.177 10 false C 1.146,1.927 1.458,2.083 0.313,0.156 10 false *1 2.167,1.135 2.479,1.292 0.313,0.156 10 false *2
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt assembly RH and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH (FRONT PRETENSIONER SQUIB RH)
a.
C238358C28
0.417,2.26 0.75,2.5 0.333,0.24 1.792,2.344 1.969,2.344 false 0.708,0.958 0.708,0.51 0.708,0.51 0.552,0.51 false 0.385,0.438 0.875,0.844 0.49,0.406 10 false *1 2.281,0.656 2.76,1.073 0.479,0.417 10 false *2 1.823,0.938 2.208,1.458 0.385,0.521 10 false A 1.677,0.938 2.167,1.417 0.49,0.479 10 false B 1.167,0.948 1.917,1.448 0.75,0.5 10 false C 0.823,0.948 1.604,1.344 0.781,0.396 10 false D 2.01,2.26 2.448,2.594 0.438,0.333 10 false SST 0.302,1.896 0.698,2.26 0.396,0.365 10 false *a 0.479,2.302 0.927,2.771 0.448,0.469 10 false F23
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Connect the connector to the airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting.

·

Insert SST straight into the terminals of the connector.




c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

6.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
6.CHECK INSTRUMENT PANEL WIRE (FRONT PRETENSIONER SQUIB RH CIRCUIT)
a.
C237240C61
0.573,2.448 0.906,2.667 0.333,0.219 1.604,2.26 1.875,2.26 true 1.146,2.26 1.417,2.26 true 0.677,1.042 0.5,0.667 true 1.427,1.042 1.25,0.667 true 0.292,0.563 0.76,0.958 0.469,0.396 10 false *1 2.271,0.76 2.604,1.135 0.333,0.375 10 false *2 1.885,1.042 2.313,1.5 0.427,0.458 10 false A 1.583,1.042 1.99,1.635 0.406,0.594 10 false B 1.125,1.042 1.542,1.552 0.417,0.51 10 false C 0.823,1.042 1.24,1.427 0.417,0.385 10 false D 1.917,2.177 2.26,2.521 0.344,0.344 10 false R- 0.948,2.177 1.438,2.521 0.49,0.344 10 false R+ 0.26,1.813 0.563,2.188 0.302,0.375 10 false *a 1.073,0.563 1.667,1.063 0.594,0.5 10 false *3 0.635,2.479 1.031,2.813 0.396,0.333 10 false F23
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly
*3 Instrument panel wire
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector C.


d.

Disconnect the Instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F23-1 (R+) - Body ground Ignition switch ON Below 1 V
F23-2 (R-) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - F23-2 (R-) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - Body ground Always 1 MΩ or higher
F23-2 (R-) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F23-1 (R+) - F23-2 (R-) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

7.CHECK AIRBAG ECU ASSEMBLY

NG

7.CHECK AIRBAG ECU ASSEMBLY
a.
C238241C19
0.417,0.75 0.833,1.292 false 0.146,0.604 0.458,0.802 0.313,0.198 10 false *1 2.104,1 2.417,1.198 0.313,0.198 10 false *2 1.729,1.292 1.885,1.49 0.156,0.198 10 false A 1.573,1.292 1.729,1.49 0.156,0.198 10 false B 1.125,1.302 1.281,1.5 0.156,0.198 10 false C 0.958,1.302 1.115,1.5 0.156,0.198 10 false D
*1 Front Pretensioner Squib RH
*2 Airbag ECU Assembly


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the front seat outer belt assembly RH and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in the memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG