The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.
The separate type front seat cushion pad (occupant detection sensor) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (passenger side) detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the separate type front seat cushion pad (occupant detection sensor) and front seat inner belt assembly (passenger side), the seat belt warning light on the combination meter assembly will blink or go off.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
| Tester Display |
|---|
| Driver Side Seat Belt |
Front seat belt warning light condition can be switched by Active Test.
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch signal | ON or OFF | OFF: Front passenger seat belt not fastened
ON: Front passenger seat belt fastened |
The front passenger seat is occupied |
| Tester Display |
|---|
| P-Seatbelt Buckle SW |
The GTS display changes correctly in response to the front passenger seat belt condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the occupant detection sensor.
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL
Inspect the occupant detection sensor.
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
| *a | Component without harness connected
(Front Seat Inner Belt Assembly (front passenger side)) |
Remove the front seat inner belt assembly RH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F121-3 (+) - B-1 | Always | Below 1 Ω |
| F121-2 (E) - B-3 | Front passenger seat belt unfastened | Below 1 Ω |
| F121-2 (E) - B-3 | Front passenger seat belt fastened | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-6 (P/SB) - F121-3 (+) | Always | Below 1 Ω |
| F38-6 (P/SB) or F121-3 (+) - Body ground | Always | 10 kΩ or higher |
| F121-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Front Seat Inner Belt Assembly (front passenger side)) |
Remove the front seat inner belt assembly LH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-3 (+) - B-1 | Always | Below 1 Ω |
| F29-2 (E) - B-3 | Front passenger seat belt unfastened | Below 1 Ω |
| F29-2 (E) - B-3 | Front passenger seat belt fastened | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-6 (P/SB) - F29-3 (+) | Always | Below 1 Ω |
| F38-6 (P/SB) or F29-3 (+) - Body ground | Always | 10 kΩ or higher |
| F29-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG