The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to unlock steering wheel (Engine cannot start) |
|
- |
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
*: for CVT
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, confirm that the problem does not recur.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly), registration must be performed (refer to Service Bulletin).
When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch.
Using the GTS, confirm the output of DTCs for all systems.
No DTCs are output.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in P*, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:
*: for CVT
Off → On (ACC) → On (IG) → Off
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch on (IG).
Check that the smart warning light on the combination meter assembly is rapidly blinking green.
| Result | Proceed to |
|---|---|
| Smart warning light is blinking rapidly. | A |
| Smart warning light is not blinking rapidly. | B |
A
B
While turning the steering wheel left and right, press the engine switch.
Check that the steering is unlocked.
The steering is unlocked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above |
·
If the unlock signal has not been received, the engine cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
The steering lock ECU (steering lock actuator assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the steering lock ECU (steering lock actuator assembly) connector.
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance and voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-1 (GND) - Body ground | Always | Below 1 Ω |
If the result is not as specified, check for looseness in the ground cable connection.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-7 (B) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-1 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the steering lock ECU (steering lock actuator assembly) connector.
Move the shift lever to P* and turn the engine switch off.
*: for CVT
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
| *b | Steering lock motor not operating |
| *c | Steering lock motor operating |
Check the signal waveform according to the condition(s) in the table below.
| Item | Content |
|---|---|
| Tester Connection | F15-3 (IGE) - F15-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Vehicle Condition | Steering lock motor not operating → Operating → Not operating |
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P*.
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
*: for CVT
| Result | Proceed to |
|---|---|
| OK (for TMT Made) | A |
| OK (for TMMIN Made) | B |
| NG | C |
A
B
C
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-3 (IGE) - F43-17 (SLR+) | Always | Below 1 Ω |
| F15-3 (IGE) - Body ground | Always | 10 kΩ or higher |
| F43-17 (SLR+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the steering lock ECU (steering lock actuator assembly) connector.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-3 (IGE) - Body ground | Always | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMT Made) | B |
| NG (for TMMIN Made) | C |
A
B
C
Replace the steering lock ECU (steering lock actuator assembly) with a new one.
for TMT Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMT Made)>DISASSEMBLY
for TMMIN Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMMIN Made)>DISASSEMBLY
Perform registration.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| L Code Check | Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) | OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly) is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the engine cannot be started). |
| Tester Display |
|---|
| L Code Check |
OK is displayed on the GTS.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance and voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly)) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-4 (SLP1) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
While turning the steering wheel left and right, press the engine switch.
Check that the steering is unlocked.
The steering is unlocked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Lock | State of whether steering lock ECU
(steering lock actuator assembly) has determined steering is locked |
Set or Unset | Set: Steering locked
Unset: Steering unlocked |
If this item displays "Unset", the steering does not lock. |
| Steering Unlock | State of whether steering lock ECU
(steering lock actuator assembly) determined steering is unlocked |
Set or Unset | Set: Steering unlocked
Unset: Steering locked |
If this item displays "Unset", the steering does not unlock (engine cannot be started). |
"Steering Lock" is "Unset" and "Steering Unlock" is "Set"
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMT Made) | B |
| NG (for TMMIN Made) | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
Perform registration.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above |
·
If the unlock signal has not been received, the engine cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMT Made) | B |
| NG (for TMMIN Made) | C |
A
B
C
Disconnect the F15 steering lock ECU (steering lock actuator assembly) connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Check for deformation and corrosion of the connector case and terminals.
There is no deformation or corrosion of the connector case or terminals.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F15-4 (SLP1) - F43-22 (SLP) | Always | Below 1 Ω |
| F15-4 (SLP1) - Body ground | Always | 10 kΩ or higher |
| F43-22 (SLP) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the steering lock ECU (steering lock actuator assembly) with a new one.
for TMT Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMT Made)>DISASSEMBLY
for TMMIN Made:
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for TMMIN Made)>DISASSEMBLY
Perform registration.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Unlock Request Receive | Reception state of steering unlock request signal by certification ECU (smart key ECU assembly)
|
OK or NG | OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
NG: Except above |
·
If the unlock signal has not been received, the engine cannot be started. ·
If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
| Tester Display |
|---|
| Unlock Request Receive |
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| Proceed to |
|---|
| OK |
| NG |
OK
NG