Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY(for Hatchback) › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334264 CURTAIN SHIELD AIRBAG ASSEMBLY(for Hatchback) A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY(for Hatchback)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 63310 3.REMOVE ROOF HEADLINING ASSEMBLY

Hide 62170A 4.REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B484599C01
1.635,2.208 1.323,2.729 true 1.865,2.198 2.396,1.667 true 0.938,0.802 1.198,0.635 true 1.146,2.646 1.375,2.844 0.229,0.198 10 false *a 1.219,0.51 1.531,0.667 0.313,0.156 10 false *b 2.438,1.563 2.646,1.75 0.208,0.188 10 false *c
*a Airbag Connector
*b Airbag Connector Lock
*c Protective Tape


Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock and disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.



d.

Using needle nose pliers, remove the 7 pins from the 7 clips (A).

B484601C01
5.906,2.063 6.208,2.281 true 5.385,2.25 5.156,2.438 5.156,2.438 5.729,2.219 true 5.104,1.656 5.396,1.656 false 3.417,1.875 3.708,1.875 false 0.354,1.323 0.271,0.813 0.271,0.813 1.021,0.979 true 6.156,2.333 6.469,2.49 0.313,0.156 10 false *1 4.938,1.552 5.25,1.708 0.313,0.156 10 false *a 2.438,0.719 2.635,0.906 0.198,0.188 10 true *b 3.729,1.771 4.042,1.927 0.313,0.156 10 false *c 4.969,2.344 5.281,2.5 0.313,0.156 10 false *d 0.094,0.719 0.406,0.875 0.313,0.156 10 false *e 4.646,0.719 4.865,0.906 0.219,0.188 10 true *b 5.198,0.781 5.396,0.958 0.198,0.177 10 true *b 3.635,0.521 3.833,0.708 0.198,0.188 10 true *b
*1 Spacer - -
*a Clip (A) *b Clip (B)
*c Pin *d Claw
*e Spacer Location - -



e.

Using 2 screwdrivers, disengage the 14 claws of 7 clips (A) to separate the 7 clips (A) from the vehicle body as shown in the illustration.

HINT:

Separate the 7 clips (A) and curtain shield airbag assembly from the vehicle body as a unit.



f.

While holding the curtain shield airbag assembly, remove the 2 bolts and disengage the 4 clips (B) to remove the curtain shield airbag assembly.


g.

Remove the 7 clips (A) and 2 spacers from the curtain shield airbag assembly.