When the engine is cranked, the starter relay assembly drive signal output from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.
While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.
*1: w/o Smart Entry and Start System
*2: w/ Smart Entry and Start System
for TMMIN Made
for TMT Made
Inspect the fuses for circuits related to this system before performing the following procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.
| Result | Proceed to |
|---|---|
| Fuel pump operating sound does not occur | A |
| Fuel pump operating sound occurs | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check whether the C/OPN relay operating sound occurs when performing the Active Test on the GTS.
Relay operating sounds can be heard from the relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pump.
Click hereEngine / Hybrid System>1NR-FE FUEL>FUEL PUMP>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2K-4 - 2O-7 | When battery voltage not applied to terminals 2L-8 and 2H-1 | 10 kΩ or higher |
| When battery voltage applied to terminals 2L-8 and 2H-1 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-6 -6H-5 | When battery voltage not applied to terminals 6L-8 and 6H-4 | 10 kΩ or higher |
| When battery voltage applied to terminals 6L-8 and 6H-4 | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMMIN Made) | B |
| NG (for TMT Made) | C |
A
B
C
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Disconnect the F28 fuel suction tube with pump and gauge assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2O-7 - F28-4 (B) | Always | Below 1 Ω |
| 2O-7 or F28-4 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-5 - F28-4 (B) | Always | Below 1 Ω |
| 6H-5 or F28-4 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F28 fuel suction tube with pump and gauge assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F28-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for CVT |
| *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F130-5 (FC) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2K-4 - 2O-7 | When battery voltage not applied to terminals 2L-8 and 2H-1 | 10 kΩ or higher |
| When battery voltage applied to terminals 2L-8 and 2H-1 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-6 - 6H-5 | When battery voltage not applied to terminals 6L-8 and 6H-4 | 10 kΩ or higher |
| When battery voltage applied to terminals 6L-8 and 6H-4 | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMMIN Made) | B |
| NG (for TMT Made) | C |
A
B
C
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Disconnect the F130 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2L-8 - F130-5 (FC) | Always | Below 1 Ω |
| 2L-8 or F130-5 (FC) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6L-8 - F130-5 (FC) | Always | Below 1 Ω |
| 6L-8 or F130-5 (FC) - Body ground and other terminals | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for TMMIN Made with Smart Entry and Start System) | A |
| OK (for TMT Made with Smart Entry and Start System) | B |
| OK (w/o Smart Entry and Start System) | C |
| NG | D |
A
B
C
D
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Remove the No. 2 ignition relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2H-1 - 5 (No. 2 ignition relay holder) | Always | Below 1 Ω |
| 2H-1 or 5 (No. 2 ignition relay relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Remove the IG2 relay from the No. 4 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2H-1 - 5 (IG2 relay holder) | Always | Below 1 Ω |
| 2H-1 or 5 (IG2 relay holder) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the driver side junction block assembly.
for TMMIN Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
for TMT Made: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Disconnect the F7 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2H-1 - F7-6 (IG2) | Always | Below 1 Ω |
| 2H-1 or F7-6 (IG2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6H-4 - F7-6 (IG2) | Always | Below 1 Ω |
| 6H-4 or F7-6 (IG2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Condition | Starter Signal |
|---|---|
| Ignition switch ON | OFF |
| Engine Started | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Read the values displayed on the GTS while cranking.
Values are displayed continuously.
| Proceed to |
|---|
| OK |
| NG |
OK
NG