Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › 2017.10–2018.01
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM J

2NR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the ST relay drive signal output from the ignition or starter switch assembly*1 or certification ECU (smart key ECU assembly)*2 is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is also input into the NE+ terminal. The ECM interprets that the engine is cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input into the ECM with the engine running, the ECM turns Tr1 on continuously.

*1: w/o Smart Entry and Start System

*2: w/ Smart Entry and Start System


WIRING DIAGRAM

for TMMIN Made


A310009E06
1.083,1.073 2.49,1.281 1.406,0.208 10 false No. 2 Ignition Relay*1 0.635,2.135 3.125,2.354 2.49,0.219 10 false Ignition or Starter Switch Assembly*2 5.208,1.292 7.021,1.677 1.813,0.385 10 false Certification ECU (Smart Key ECU Assembly)*1 0.948,4.927 3.438,5.146 2.49,0.219 10 false Driver Side Junction Block Assembly 2.313,6.24 4.146,6.625 1.833,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 4.198,5.979 5.24,6.323 1.042,0.344 10 false from STA Signal Circuit 4.198,6.635 5.208,7 1.01,0.365 10 false from Crankshaft Position Sensor 0.99,7.219 3.323,7.438 2.333,0.219 10 false *1: w/ Smart Entry and Start System 0.979,7.521 3.313,7.74 2.333,0.219 10 false *2: w/o Smart Entry and Start System 0.615,6.385 1.094,6.604 0.479,0.219 10 false Battery 0.469,5.156 0.948,5.375 0.479,0.219 10 false MAIN 1.677,3.135 2.156,3.354 0.479,0.219 10 false AM2 2.313,6.073 2.792,6.292 0.479,0.219 10 false F28 1.49,5.948 1.708,6.177 0.219,0.229 10 false B 1.49,6.583 1.708,6.813 0.219,0.229 10 false E 1.49,6.802 1.708,7.031 0.219,0.229 10 false 5 1.5,5.719 1.719,5.948 0.219,0.229 10 false 4 0.635,2 1.115,2.219 0.479,0.219 10 false F7 1.083,0.927 1.563,1.146 0.479,0.219 10 false F77 2.969,4.667 3.188,4.896 0.219,0.229 10 false 4 1.219,4.073 1.438,4.302 0.219,0.229 10 false 7 4.635,4.083 4.833,4.302 0.198,0.219 10 false 9 1.219,3.531 1.417,3.75 0.198,0.219 10 false 1 4.635,3.542 4.854,3.74 0.219,0.198 10 false 7 4.635,3.135 4.854,3.333 0.219,0.198 10 false 8 2.875,2.573 3.094,2.771 0.219,0.198 10 false 1 1.573,3.906 2.281,4.115 0.708,0.208 10 false EFI-MAIN 3.281,2.927 3.99,3.135 0.708,0.208 10 false IG2 NO. 1 3.729,4.073 4.438,4.281 0.708,0.208 10 false C/OPN 3.198,4.677 3.51,4.854 0.313,0.177 10 false 2K 1.177,4.292 1.49,4.469 0.313,0.177 10 false 2J 1.167,3.75 1.479,3.927 0.313,0.177 10 false 2B 3.125,2.573 3.438,2.75 0.313,0.177 10 false 2H 4.604,3.323 4.917,3.5 0.313,0.177 10 false 2L 4.583,3.75 4.896,3.927 0.313,0.177 10 false 2O 4.594,4.292 4.906,4.469 0.313,0.177 10 false 2L 5.719,6.917 6.031,7.094 0.313,0.177 10 false B46 5.719,6.49 6.031,6.667 0.313,0.177 10 false B46 5.729,6 6.083,6.177 0.354,0.177 10 false B47 5.688,5.594 6.042,5.771 0.354,0.177 10 false F131 5.688,5.188 6.042,5.365 0.354,0.177 10 false F131 5.688,4.292 6.042,4.469 0.354,0.177 10 false F130 5.688,3.323 6.042,3.5 0.354,0.177 10 false F130 1.042,1.542 1.521,1.76 0.479,0.219 10 false AM2 2.198,1.542 2.677,1.76 0.479,0.219 10 false IG2 2.719,1.781 3.031,1.958 0.313,0.177 10 false *2 0.646,1.771 0.958,1.948 0.313,0.177 10 false *2 0.427,1 0.74,1.177 0.313,0.177 10 false *1 0.906,0.76 1.219,0.938 0.313,0.177 10 false *1 3.24,1.135 3.552,1.313 0.313,0.177 10 false *1 4.219,0.76 4.531,0.938 0.313,0.177 10 false *1 2.521,1.542 2.74,1.74 0.219,0.198 10 false 6 0.854,1.542 1.073,1.74 0.219,0.198 10 false 5 1.229,0.552 1.458,0.76 0.229,0.208 10 false 1 1.24,0.167 1.469,0.375 0.229,0.208 10 false 3 2.156,0.177 2.385,0.385 0.229,0.208 10 false 5 2.167,0.563 2.396,0.771 0.229,0.208 10 false 2 5.021,0.521 5.25,0.729 0.229,0.208 10 false 20 5.323,0.635 5.802,0.854 0.479,0.219 10 false IG1D 5.219,1.146 5.698,1.365 0.479,0.219 10 false F43 5.802,3.115 6.021,3.313 0.219,0.198 10 false 5 5.802,4.083 6.021,4.281 0.219,0.198 10 false 6 5.802,4.958 6.021,5.156 0.219,0.198 10 false 1 5.792,5.385 6.01,5.583 0.219,0.198 10 false 2 5.76,5.802 5.979,6 0.219,0.198 10 false 17 5.771,6.281 5.99,6.479 0.219,0.198 10 false 27 5.76,6.708 5.979,6.906 0.219,0.198 10 false 34 6.083,3.458 6.396,3.635 0.313,0.177 10 false FC 6.083,4.281 6.552,4.458 0.469,0.177 10 false MREL 6.083,5.167 6.396,5.344 0.313,0.177 10 false +B 6.083,5.563 6.396,5.74 0.313,0.177 10 false +B2 6.083,6 6.396,6.177 0.313,0.177 10 false STA 6.083,6.49 6.469,6.688 0.385,0.198 10 false NE+ 6.083,6.917 6.396,7.094 0.313,0.177 10 false NE- 6.344,7.344 6.833,7.521 0.49,0.177 10 false ECM 2.49,4.563 2.823,4.74 0.333,0.177 10 false EFI 1.167,2.771 1.479,2.948 0.313,0.177 10 false 2H 1.219,2.563 1.417,2.781 0.198,0.219 10 false 5 1.594,6.26 2.458,6.49 0.865,0.229 10 false Fuel Pump 0.469,5.688 1.125,5.938 0.656,0.25 10 false FL MAIN


for TMT Made


A310009E14
1.375,0.969 2.781,1.177 1.406,0.208 10 false IG2 Relay*1 0.635,2.135 3.125,2.354 2.49,0.219 10 false Ignition or Starter Switch Assembly*2 5.208,1.292 7.021,1.677 1.813,0.385 10 false Certification ECU (Smart Key ECU Assembly)*1 0.948,4.927 3.438,5.146 2.49,0.219 10 false Driver Side Junction Block Assembly 2.313,6.24 4.146,6.625 1.833,0.385 10 false Fuel Suction Tube with Pump and Gauge Assembly 4.198,5.979 5.24,6.323 1.042,0.344 10 false from STA Signal Circuit 4.198,6.635 5.208,7 1.01,0.365 10 false from Crankshaft Position Sensor 0.99,7.219 3.323,7.438 2.333,0.219 10 false *1: w/ Smart Entry and Start System 0.979,7.521 3.313,7.74 2.333,0.219 10 false *2: w/o Smart Entry and Start System 0.615,6.385 1.094,6.604 0.479,0.219 10 false Battery 0.469,5.156 0.948,5.375 0.479,0.219 10 false MAIN 1.677,3.135 2.156,3.354 0.479,0.219 10 false AM2 2.313,6.073 2.792,6.292 0.479,0.219 10 false F28 1.49,5.948 1.708,6.177 0.219,0.229 10 false B 1.49,6.583 1.708,6.813 0.219,0.229 10 false E 1.49,6.802 1.708,7.031 0.219,0.229 10 false 5 1.5,5.719 1.719,5.948 0.219,0.229 10 false 4 0.635,2 1.115,2.219 0.479,0.219 10 false F7 2.969,4.667 3.188,4.896 0.219,0.229 10 false 6 1.219,4.073 1.438,4.302 0.219,0.229 10 false 8 4.635,4.083 4.833,4.302 0.198,0.219 10 false 9 1.219,3.531 1.417,3.75 0.198,0.219 10 false 1 4.635,3.542 4.854,3.74 0.219,0.198 10 false 5 4.635,3.135 4.854,3.333 0.219,0.198 10 false 8 2.875,2.573 3.094,2.771 0.219,0.198 10 false 4 1.573,3.906 2.281,4.115 0.708,0.208 10 false EFI-MAIN 3.281,2.927 3.99,3.135 0.708,0.208 10 false IG2 NO. 1 3.729,4.073 4.438,4.281 0.708,0.208 10 false C/OPN 3.198,4.677 3.51,4.854 0.313,0.177 10 false 6H 1.177,4.292 1.49,4.469 0.313,0.177 10 false 6J 1.167,3.75 1.479,3.927 0.313,0.177 10 false 6B 3.125,2.573 3.438,2.75 0.313,0.177 10 false 6H 4.604,3.323 4.917,3.5 0.313,0.177 10 false 6L 4.583,3.75 4.896,3.927 0.313,0.177 10 false 6H 4.594,4.292 4.906,4.469 0.313,0.177 10 false 6L 5.719,6.917 6.031,7.094 0.313,0.177 10 false B46 5.719,6.49 6.031,6.667 0.313,0.177 10 false B46 5.729,6 6.083,6.177 0.354,0.177 10 false B47 5.688,5.594 6.042,5.771 0.354,0.177 10 false F131 5.688,5.188 6.042,5.365 0.354,0.177 10 false F131 5.688,4.292 6.042,4.469 0.354,0.177 10 false F130 5.688,3.323 6.042,3.5 0.354,0.177 10 false F130 1.042,1.542 1.521,1.76 0.479,0.219 10 false AM2 2.198,1.542 2.677,1.76 0.479,0.219 10 false IG2 2.719,1.781 3.031,1.958 0.313,0.177 10 false *2 0.646,1.771 0.958,1.948 0.313,0.177 10 false *2 0.427,1 0.74,1.177 0.313,0.177 10 false *1 0.906,0.76 1.219,0.938 0.313,0.177 10 false *1 3.24,1.135 3.552,1.313 0.313,0.177 10 false *1 4.219,0.76 4.531,0.938 0.313,0.177 10 false *1 2.521,1.542 2.74,1.74 0.219,0.198 10 false 6 0.854,1.542 1.073,1.74 0.219,0.198 10 false 5 1.229,0.552 1.458,0.76 0.229,0.208 10 false 1 1.24,0.167 1.469,0.375 0.229,0.208 10 false 3 2.156,0.177 2.385,0.385 0.229,0.208 10 false 5 2.167,0.563 2.396,0.771 0.229,0.208 10 false 2 5.021,0.521 5.25,0.729 0.229,0.208 10 false 20 5.323,0.635 5.802,0.854 0.479,0.219 10 false IG1D 5.219,1.146 5.698,1.365 0.479,0.219 10 false F43 5.802,3.115 6.021,3.313 0.219,0.198 10 false 5 5.802,4.083 6.021,4.281 0.219,0.198 10 false 6 5.802,4.958 6.021,5.156 0.219,0.198 10 false 1 5.792,5.385 6.01,5.583 0.219,0.198 10 false 2 5.76,5.802 5.979,6 0.219,0.198 10 false 17 5.771,6.281 5.99,6.479 0.219,0.198 10 false 27 5.76,6.708 5.979,6.906 0.219,0.198 10 false 34 6.083,3.458 6.396,3.635 0.313,0.177 10 false FC 6.083,4.281 6.552,4.458 0.469,0.177 10 false MREL 6.083,5.167 6.396,5.344 0.313,0.177 10 false +B 6.083,5.563 6.396,5.74 0.313,0.177 10 false +B2 6.083,6 6.396,6.177 0.313,0.177 10 false STA 6.083,6.49 6.469,6.688 0.385,0.198 10 false NE+ 6.083,6.917 6.396,7.094 0.313,0.177 10 false NE- 6.344,7.344 6.833,7.521 0.49,0.177 10 false ECM 2.49,4.563 2.823,4.74 0.333,0.177 10 false EFI 1.167,2.771 1.479,2.948 0.313,0.177 10 false 6H 1.219,2.563 1.417,2.781 0.198,0.219 10 false 7 1.594,6.26 2.458,6.49 0.865,0.229 10 false Fuel Pump 0.469,5.688 1.125,5.938 0.656,0.25 10 false FL MAIN


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)

B

13.READ VALUE USING GTS (STARTER SIGNAL)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the C/OPN relay operating sound occurs when performing the Active Test on the GTS.

OK:

Relay operating sounds can be heard from the relay.



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PUMP

NG

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
3.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

NG

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for TMMIN Made):
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω


Standard Resistance (for TMT Made):
Tester Connection Condition Specified Condition
6H-6 - 6H-5 When battery voltage not applied to terminals 6L-8 and 6H-4 10 kΩ or higher
When battery voltage applied to terminals 6L-8 and 6H-4 Below 1 Ω



Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

B

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

C

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)

b.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for TMMIN Made):
Tester Connection Condition Specified Condition
2O-7 - F28-4 (B) Always Below 1 Ω
2O-7 or F28-4 (B) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for TMT Made):
Tester Connection Condition Specified Condition
6H-5 - F28-4 (B) Always Below 1 Ω
6H-5 or F28-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - BODY GROUND)
a.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F28-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK TERMINAL VOLTAGE (FC TERMINAL VOLTAGE)
a.
A342760C05
2.01,0.5 2.51,0.75 0.5,0.25 1.583,2.667 2.083,2.917 0.5,0.25 2.563,1.823 2.125,1.01 true 2.156,3.99 1.719,3.177 true 0.104,0.135 0.417,0.333 0.313,0.198 10 false *a 0.333,0.417 0.708,0.656 0.375,0.24 12 false *A 0.354,2.51 0.729,2.75 0.375,0.24 12 false *B 2.083,0.531 2.698,0.729 0.615,0.198 10 false F130 1.646,2.698 2.26,2.896 0.615,0.198 10 false F130 2.49,1.844 3.104,2.042 0.615,0.198 10 false FC 2.073,4.01 2.688,4.208 0.615,0.198 10 false FC
*A for CVT
*B for Manual Transaxle
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-5 (FC) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

NG

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (C/OPN RELAY)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for TMMIN Made):
Tester Connection Condition Specified Condition
2K-4 - 2O-7 When battery voltage not applied to terminals 2L-8 and 2H-1 10 kΩ or higher
When battery voltage applied to terminals 2L-8 and 2H-1 Below 1 Ω


Standard Resistance (for TMT Made):
Tester Connection Condition Specified Condition
6H-6 - 6H-5 When battery voltage not applied to terminals 6L-8 and 6H-4 10 kΩ or higher
When battery voltage applied to terminals 6L-8 and 6H-4 Below 1 Ω



Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

B

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

C

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

b.

Disconnect the F130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for TMMIN Made):
Tester Connection Condition Specified Condition
2L-8 - F130-5 (FC) Always Below 1 Ω
2L-8 or F130-5 (FC) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for TMT Made):
Tester Connection Condition Specified Condition
6L-8 - F130-5 (FC) Always Below 1 Ω
6L-8 or F130-5 (FC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Result Proceed to
OK (for TMMIN Made with Smart Entry and Start System) A
OK (for TMT Made with Smart Entry and Start System) B
OK (w/o Smart Entry and Start System) C
NG D



A

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 2 IGNITION RELAY)

B

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IG2 RELAY)

C

12.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - NO. 2 IGNITION RELAY)

b.

Remove the No. 2 ignition relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2H-1 - F77-5 (No. 2 ignition relay holder) Always Below 1 Ω
2H-1 or F77-5 (No. 2 ignition relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IG2 RELAY)

b.

Remove the IG2 relay from the No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6H-4 - 5 (No. 4 relay holder) Always Below 1 Ω
6H-4 or 5 (No. 4 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)

b.

Disconnect the F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for TMMIN Made):
Tester Connection Condition Specified Condition
2H-1 - F7-6 (IG2) Always Below 1 Ω
2H-1 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (for TMT Made):
Tester Connection Condition Specified Condition
6H-4 - F7-6 (IG2) Always Below 1 Ω
6H-4 or F7-6 (IG2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the result when the ignition switch is ON and the engine starts.

OK:
Condition Starter Signal
Ignition switch ON OFF
Engine Started ON



Result:
Proceed to
OK
NG



OK

14.READ VALUE USING GTS (ENGINE SPEED)

NG

14.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT