Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS(for TMMIN Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0334657 BACK WINDOW GLASS(for TMMIN Made) A

WINDOW / GLASS  BACK WINDOW GLASS(for TMMIN Made)  REMOVAL  


PROCEDURE

Hide 2.REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

Hide 3.REMOVE REAR SEAT ASSEMBLY (for Separate Seat Type)

Hide 62332A 4.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the rear door opening trim weatherstrip LH to the extent that the rear seat side garnish LH, roof side inner garnish assembly LH and roof headlining assembly can be removed.


Hide 62331A 5.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73370 6.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 73360 7.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62551F 9.REMOVE REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62471A 11.REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64330D 12.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 63339A 14.REMOVE ROOF HEADLINING SERVICE HOLE COVER (w/ Cover)

Hide 63310 15.SEPARATE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining assembly.

HINT:

It is not necessary to completely remove the roof headlining assembly. Slightly lower the rear section of the roof headlining assembly so that the back window glass can be removed in a later step.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for TMMIN Made Sedan)>REMOVAL



Hide 64811 16.REMOVE BACK WINDOW GLASS

a.
B343882C01
0,0 0.281,0 false
V100155

Protective Tape


Apply protective tape to the installation area on the back window glass on the vehicle body.


b.
B343884C01
2,1.052 1.885,1.375 1.885,1.375 2.208,1.25 true 1.771,1.375 2.083,1.531 0.313,0.156 10 false *a
*a Matchmarks


Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks are not needed to be placed if the back window glass will not be reused.



c.

Disconnect each connector.


d.
B348885C01
2.063,1.615 2.385,1.906 true 1.865,0.927 2.198,0.688 false 1.406,0.74 1.74,0.5 false 2.417,1.927 2.729,2.125 0.313,0.198 10 false *a 2.208,0.573 2.521,0.771 0.313,0.198 10 false *b 1.75,0.375 2.063,0.573 0.313,0.198 10 false *c
*a Wooden Block
*b Plastic Sheet
*c Piano Wire


Pass a piano wire between the vehicle body and back window glass from the interior.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


f.

Cut off the adhesive by pulling the piano wire around the back window glass.

NOTICE:
·

When separating the back window glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the back window glass, place a plastic sheet between the piano wire and safety pad.




g.

Disconnect the back window glass stoppers.

B343881C01
1.354,2.25 1.573,2.25 false 4.885,2.208 5.021,2.021 false 5.01,2.438 5.146,2.25 false 1,1.563 1.323,1.771 0.323,0.208 12 false *A 4.531,1.573 4.844,1.813 0.313,0.24 12 false *B 1.188,2.177 1.5,2.333 0.313,0.156 10 false *1 4.719,2.146 5.031,2.302 0.313,0.156 10 false *2 4.802,2.396 5.115,2.552 0.313,0.156 10 false *1
*A 1-piece type *B 2-piece type
*1 No. 1 Back Window Glass Stopper *2 No. 2 Back Window Glass Stopper


NOTICE:
·

There are No. 1 and No. 2 back window glass stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.

·

To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type back window glass stoppers may be present.



h.

Using suction cups, remove the back window glass.

NOTICE:
·

Be careful not to drop the back window glass.

·

Leave as much adhesive on the vehicle body as possible when removing the back window glass.




Hide 64813D 17.REMOVE BACK WINDOW GLASS ADHESIVE DAM

a.
B343899C01
0.021,0.021 0.333,0.177 0.313,0.156 10 false *a
*a Back Side


Using a scraper, remove the back window glass adhesive dam.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the back window glass adhesive dam with a new one.




Hide 56115B 18.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)

a.
B343900C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Back Side


Using a scraper, remove the 2 No. 1 back window glass stoppers.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the No. 1 back window glass stoppers with new ones.




Hide 56116D 19.REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.
B343900C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Back Side


Using a scraper, remove the 2 No. 2 back window glass stoppers.

NOTICE:
·

Be careful not to damage the back window glass.

·

Be sure to replace the No. 2 back window glass stoppers with new ones.




Hide 56115B 20.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.
B343886

Remove the 2 No. 1 back window glass stoppers.

NOTICE:

Be sure to replace the No. 1 back window glass stoppers with new ones.