81006
1.REMOVE CENTER STOP LIGHT SET
2.REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)
3.REMOVE REAR SEAT ASSEMBLY (for Separate Seat Type)
67918A
4.REMOVE REAR DOOR SCUFF PLATE LH
67917A
5.REMOVE REAR DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
62332A
6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the rear door opening trim weatherstrip LH to the extent that the side rear seat side garnish LH and roof side inner garnish LH can be removed.
62331A
7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
73370
8.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
73360
9.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH
Use the same procedure as for the LH side.
62552F
10.REMOVE REAR SEAT SIDE GARNISH LH
62551F
11.REMOVE REAR SEAT SIDE GARNISH RH
Use the same procedure as for the LH side.
62472A
12.REMOVE ROOF SIDE INNER GARNISH LH
62471A
13.REMOVE ROOF SIDE INNER GARNISH RH
Use the same procedure as for the LH side.
64330D
14.REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
74610A
15.REMOVE ASSIST GRIP SUB-ASSEMBLY
63310
16.REMOVE ROOF HEADLINING ASSEMBLY
Partially remove the roof headlining.
It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining so that the back window glass can be removed in a later step.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING(for TMT Made Sedan)>REMOVAL
64811
17.REMOVE BACK WINDOW GLASS
|
Protective Tape |
Apply protective tape to the installation area on the back window glass on the vehicle body.
| *a | Matchmark |
Place matchmarks on the back window glass and vehicle body on the locations indicated in the illustration.
Matchmarks are not needed to be placed if the back window glass will not be reused.
Disconnect each connector.
| *1 | Window Glass Stopper |
| *a | Piano Wire |
Pass a piano wire between the vehicle body and back window from the interior.
Tie both wire ends to wooden blocks or similar objects.
Cut off the adhesive by pulling the piano wire around the back window glass.
When separating the back window glass from the vehicle, be careful not to damage the paint or interior and exterior ornaments.
Disconnect the back window glass stoppers.
| *A | 1-piece type | *B | 2-piece type |
| *1 | No. 1 Back Window Glass Stopper | *2 | No. 2 Back Window Glass Stopper |
There are No. 1 and No. 2 stoppers on the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.
To prevent the back window glass from falling when performing this operation, be sure to hold the back window glass using suction cups.
Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.
Using suction cups, remove the back window glass.
Be careful not to drop the back window glass.
Leave as much adhesive on the vehicle body as possible when removing the back window glass.
64813D
18.REMOVE BACK WINDOW GLASS ADHESIVE DAM
| *a | Back Side |
Using a scraper, remove the back window glass adhesive dam.
Be careful not to damage the back window glass.
Be sure to replace the back window glass adhesive dam with a new one.
19.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)
| *a | Back Side |
Using a scraper, remove the 2 No. 1 back window glass stoppers.
Be careful not to damage the back window glass.
Be sure to replace the No. 1 back window glass stoppers with new ones.
56116D
20.REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)
| *a | Back Side |
Using a scraper, remove the 2 No. 2 back window glass stoppers.
Be careful not to damage the back window glass.
Be sure to replace the No. 2 back window glass stoppers with new ones.
56115B
21.REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 back window glass stoppers.
Be sure to replace the No. 1 back window glass stoppers with new ones.