Home › Vehicle Exterior › WINDOW / GLASS › BACK WINDOW GLASS(for TMT Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017121 WINDOW / GLASS _0334665 BACK WINDOW GLASS(for TMT Made) A

WINDOW / GLASS  BACK WINDOW GLASS(for TMT Made)  INSTALLATION  


PROCEDURE

Hide 64811 1.CLEAN BACK WINDOW GLASS

a.

When reusing the back window glass:

i.
B187131

Using a scraper, remove any adhesive dam and adhesive residue from the back window glass.

NOTICE:

Be careful not to damage the back window glass.




b.

Clean the outer circumference of the back window glass with a non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean it with a non-residue solvent.




Hide 2. CLEAN VEHICLE BODY

a.
B149737C22
0.833,1.542 1.083,1.75 true 0.667,0.5 1,0.667 false 2.167,0.49 2.5,0.656 false 2.281,1.521 2.531,1.729 true 1.125,1.74 1.531,2 0.406,0.26 10 false *a 2.583,1.729 2.969,2 0.385,0.271 10 false *a 0.5,0.385 0.813,0.604 0.313,0.219 10 false *b 2.01,0.375 2.281,0.594 0.271,0.219 10 false *b
*a Adhesive
*b Body


Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away any rough adhesive on the contact surface of the vehicle body to ensure the appropriate surface shape.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.




Hide 56116D 3.INSTALL NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the application area of 2 new No. 2 back window glass stoppers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than that specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the 2 new No. 2 back window glass stoppers onto the back window glass as shown in the illustration.

B484688C01
0.542,1.177 0.74,1.49 true 6.646,1.229 6.448,1.479 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a 0.438,1.021 0.75,1.219 0.313,0.198 10 false b 1.552,1 1.698,1.198 0.146,0.198 10 false a 5.542,1.01 5.688,1.208 0.146,0.198 10 false a 6.625,1.021 6.938,1.219 0.313,0.198 10 false b
*a Back Side - -


Standard Dimension:
Area Dimension Area Dimension
a 40 mm (1.57 in.) b 14.6 to 15.6 mm (0.575 to 0.614 in.)


HINT:

Only 2-piece type No. 2 back window glass stoppers are supplied. Use the 2-piece type stoppers even if a 1-piece type was used.



Hide 56115B 4.INSTALL NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)

a.
B484689C01
1.125,1.76 1.208,1.552 false 1,1.771 1.313,1.969 0.313,0.198 10 false *1
*1 No. 1 Back Window Glass Stopper


Install 2 new No. 1 back window glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type back window glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if a 1-piece type was originally installed.



Hide 64813D 5.INSTALL BACK WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of a new back window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer G for later use.



HINT:

If an area other than that specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the new back window adhesive dam, applying double-sided tape all the way around the glass except where the dam is installed as shown in the illustration.

B484690C01
0.344,1.042 0.552,0.865 true 0.479,1.406 0.448,1.146 true 5.146,0.854 5.333,1.031 true 5.135,1.448 5.24,1.146 true 0.156,0.083 0.469,0.281 0.313,0.198 10 false *a 0.531,0.719 0.844,0.917 0.313,0.198 10 false *1 0.448,1.479 0.76,1.677 0.313,0.198 10 false *b 1.573,2.49 1.885,2.688 0.313,0.198 10 false D 1.938,2.5 2.135,2.677 0.198,0.177 10 false D 3.073,1.49 3.271,1.667 0.198,0.177 10 false A 3.042,1.854 3.24,2.031 0.198,0.177 10 false A 3.063,2.719 3.26,2.896 0.198,0.177 10 false B 3.052,3.104 3.25,3.281 0.198,0.177 10 false B 3.604,1.979 3.802,2.156 0.198,0.177 10 false C 3.948,1.948 4.146,2.125 0.198,0.177 10 false C 5.896,2.042 6.698,2.208 0.802,0.167 10 false C - C, D - D 5.958,0.49 6.396,0.708 0.438,0.219 10 false A - A 5.969,1 6.125,1.198 0.156,0.198 10 false a 6.552,2.958 6.708,3.156 0.156,0.198 10 false c 4.573,2.688 4.729,2.885 0.156,0.198 10 false b 4.51,2.052 4.948,2.271 0.438,0.219 10 false B - B 4.979,0.74 5.292,0.938 0.313,0.198 10 false *1 5,1.479 5.313,1.677 0.313,0.198 10 false *b
*1 Back Window Glass Adhesive Dam - -
*a Back Side *b Ceramic Notch


Standard Dimension:
Area Dimension Area Dimension
a 7.0 mm (0.276 in.) b 13.7 mm (0.539 in.)
c 6.6 mm (0.260 in.) - -



Hide 64811 6.INSTALL BACK WINDOW GLASS

a.
B484681C02
2.125,1.594 1.875,1.719 1.875,1.719 1.948,1.427 true 1.698,1.729 2.01,1.927 0.313,0.198 10 false *a
*a Matchmark


Position the back window glass.

i.

Using suction cups, place the back window glass in the correct position.


ii.

Check that the whole contact surface of the back window glass rim is perfectly even.


iii.

Align the matchmarks on the back window glass and vehicle body.

NOTICE:

Check that the back window glass stoppers are attached to the vehicle body correctly.



iv.

Remove the back window glass.



b.
B317081C02
1.958,0.708 2.281,0.844 false 2,1.99 2.219,1.906 false 1.958,1.646 2.271,1.781 false 3,0.479 3.313,0.677 0.313,0.198 10 false *c 2.958,1.438 3.271,1.635 0.313,0.198 10 false *d 1.802,0.615 2.115,0.813 0.313,0.198 10 false *a 1.823,1.927 2.135,2.125 0.313,0.198 10 false *b 1.802,1.542 2.115,1.74 0.313,0.198 10 false *a
*a Primer M
*b Adhesive
*c CORRECT
*d INCORRECT


Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.


·

Do not apply too much primer M.


·

Allow the primer coating to dry for 3 minutes or more.


·

Do not keep any of the opened primer M for later use.




c.

Using a brush or sponge, coat the adhesive application area with primer G.

B484691C01
0.094,0.115 0.406,0.313 0.313,0.198 10 false *a 3.698,0.177 4.156,0.375 0.458,0.198 10 false A -A 5.635,0.177 6.094,0.375 0.458,0.198 10 false B -B 3.604,1.979 4.063,2.177 0.458,0.198 10 false C -C 5.604,1.99 6.458,2.188 0.854,0.198 10 false D -D, E - E 1.781,0.875 1.979,1.052 0.198,0.177 10 false A 1.781,1.26 1.979,1.438 0.198,0.177 10 false A 2.406,0.813 2.604,0.99 0.198,0.177 10 false B 2.427,1.167 2.594,1.344 0.167,0.177 10 true B 2.281,1.396 2.448,1.573 0.167,0.177 10 true E 2.635,1.375 2.802,1.552 0.167,0.177 10 true E 1.75,2.104 1.917,2.281 0.167,0.177 10 true D 1.76,2.469 1.927,2.646 0.167,0.177 10 true D 1.042,2.073 1.208,2.25 0.167,0.177 10 true C 0.958,2.427 1.125,2.604 0.167,0.177 10 true C 3.823,0.969 3.979,1.167 0.156,0.198 10 false a 5.677,0.729 5.833,0.927 0.156,0.198 10 false b 4.302,3.125 4.458,3.323 0.156,0.198 10 false c 5.667,2.792 5.823,2.99 0.156,0.198 10 false d
*a Back Side - -
V100155

Primer G - -


Standard Dimension:
Area Dimension Area Dimension
a 11.0 mm (0.433 in.) or more b 10.0 mm (0.394 in.) or more
c 19.0 mm (0.748 in.) or more d 11.0 mm (0.433 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G coating to dry for 3 minutes or more.

·

Do not keep any of the opened primer G for later use.



HINT:
·

Apply primer G onto the ceramic notches.


·

If an area other than that specified is coated by accident, wipe off the primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the back window glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C29
1.198,0.448 1.792,0.667 true 0.802,1.635 0.604,1.938 true 0.76,1 1.021,1.26 0.26,0.26 10 false A 1.854,0.625 2.167,0.896 0.313,0.271 10 false *a 1.115,0.896 1.385,1.146 0.271,0.25 10 false A 0.531,0.646 0.802,0.875 0.271,0.229 10 false B 1.302,1.458 1.594,1.708 0.292,0.25 10 false B 0.49,1.948 0.802,2.146 0.313,0.198 10 false *b
*a Nozzle
*b Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
A 8.0 mm (0.315 in.)
B 12.0 mm (0.472 in.)


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window glass as shown in the illustration.

B484692C01
0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.781,0.396 2.094,0.594 0.313,0.198 10 false A 1.76,0.802 2.073,1 0.313,0.198 10 false A 2.417,0.354 2.729,0.552 0.313,0.198 10 false B 2.427,0.688 2.573,0.885 0.146,0.198 10 true B 2.302,0.906 2.448,1.104 0.146,0.198 10 false C 2.625,0.885 2.771,1.083 0.146,0.198 10 true C 1.052,1.604 1.198,1.802 0.146,0.198 10 true D 0.958,1.969 1.104,2.167 0.146,0.198 10 true D 1.781,1.656 1.927,1.854 0.146,0.198 10 false E 1.781,1.99 1.927,2.188 0.146,0.198 10 false E 3.677,0.125 4.094,0.333 0.417,0.208 10 false A - A 5.646,0.104 6.063,0.313 0.417,0.208 10 false B - B 3.583,2.063 4,2.271 0.417,0.208 10 false D - D 5.615,2.021 6.031,2.229 0.417,0.208 10 false E - E 2.365,3.354 2.521,3.552 0.156,0.198 10 false c 4.365,3.479 4.521,3.677 0.156,0.198 10 false e 4.802,3.167 4.958,3.365 0.156,0.198 10 false d 5.719,2.833 5.875,3.031 0.156,0.198 10 false f 1.594,2.333 2.01,2.542 0.417,0.208 10 false C - C 3.719,0.833 3.875,1.031 0.156,0.198 10 false a 5.708,0.719 5.865,0.917 0.156,0.198 10 false b
*a Back Side - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension Area Dimension
a 14.7 mm (0.579 in.) b 10.0 mm (0.394 in.)
c 14.7 mm (0.579 in.) d 20.2 mm (0.795 in.)
e 8.0 mm (0.315 in.) f 20.2 mm (0.795 in.)




e.

Install the back window glass.

i.
B484693C01
2.125,1.573 1.885,1.698 1.885,1.698 1.948,1.448 true 1.76,1.719 1.958,1.917 0.198,0.198 10 false *a
*a Matchmark


Using suction cups, position the back window glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the back window glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and back window glass.




ii.

Lightly press the front surface of the back window glass to ensure a close fit.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the back window glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time Prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.

Connect each connector.


g.

Clean the contact surface of the vehicle body with a piece of cloth saturated with cleaner.


Hide 7.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63310 8.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the roof headlining to its original position.


Hide 64330D 10.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

Hide 62471A 12.INSTALL ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62551F 14.INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73370 15.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 73360 16.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 17.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Connect the rear door opening trim weatherstrip LH.


Hide 62331A 18.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 20.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 21.INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)

Hide 22.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)