Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM › from 2017.10
RM30M0E _56 Audio / Visual / Telematics _068680 PARK ASSIST / MONITORING _0335855 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The clearance warning ECU assembly receives the reverse signal from the park/neutral position switch.

WIRING DIAGRAM

E318095E11
5.365,0.969 5.677,1.167 0.313,0.198 10 false RL 5.115,0.875 5.427,1.073 0.313,0.198 10 false 21 3.021,0.885 3.333,1.083 0.313,0.198 10 false 1 4.583,0.844 4.896,1.042 0.313,0.198 10 false 2 2.135,1.146 3.25,1.365 1.115,0.219 10 false ECU-IG NO. 1 0.469,1 1.844,1.833 1.375,0.833 10 false from IG1 Relay 3.021,1.427 4.344,1.635 1.323,0.208 10 false B56 3.01,1.594 5.042,1.896 2.031,0.302 10 false Park/Neutral Position Switch 4.906,1.885 6.229,2.094 1.323,0.208 10 false F176 4.896,2.052 7.094,2.323 2.198,0.271 10 false Clearance Warning ECU Assembly 4.271,0.885 4.583,1.083 0.313,0.198 10 false RL 3.229,0.885 3.542,1.083 0.313,0.198 10 false RB

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY)
a.
E373520C05
1.417,0.25 1.917,0.5 0.5,0.25 2.385,1.906 2.146,1.344 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 1.49,0.292 1.99,0.563 0.5,0.271 10 false F176 2.354,1.938 2.667,2.135 0.313,0.198 10 false RL
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F176-21 (RL) - Body ground
·

Engine switch ON

·

Shift lever in R


11 to 14 V
F176-21 (RL) - Body ground
·

Engine switch ON

·

Shift lever in any position other than R


Below 1 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARK / NEUTRAL POSITION SWITCH
2.INSPECT PARK / NEUTRAL POSITION SWITCH
a.

Remove the park/neutral position switch.

Click hereDrivetrain>K312 CVT>PARK / NEUTRAL POSITION SWITCH>REMOVAL


b.

Inspect the park/neutral position switch.

Click hereDrivetrain>K312 CVT>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)

NG

REPLACE PARK / NEUTRAL POSITION SWITCH

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
a.
C330140C44
1.479,0.271 1.927,0.552 0.448,0.281 1.573,1.042 0.99,0.625 true 0.74,0.552 1.052,0.75 0.313,0.198 10 false RB 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.573,0.344 2.042,0.542 0.469,0.198 10 false B56
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.

i.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B56-1 (RB) - Body ground Engine switch ON (IG) 11 to 14 V




b.

Disconnect the F176 clearance warning ECU assembly connector.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F176-21 (RL) - B56-2 (RL) Always Below 1 Ω
F176-21 (RL) or B56-2 (RL) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR