Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  C1513  Torque Sensor Deviation Excessive  


DESCRIPTION

The power steering ECU assembly supplies a voltage of 5 V to the torque sensor (electric power steering column sub-assembly) and monitors the voltage value of the Hall IC inside the torque sensor (electric power steering column sub-assembly) which changes in response to changes in the magnetic flux density (steering torque) detected by the Hall IC, and calculates the assist torque.

The Hall IC is a duplex system, and the power steering ECU assembly monitors the total value of TRQ1 (Hall IC 1) voltage and TRQ2 (Hall IC 2) voltage to detect malfunctions in the torque sensor (electric power steering column sub-assembly).

While DTC C1513 is detected, power assist is stopped due to fail-safe operation.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1513 Torque Sensor Deviation Excessive Deviation of torque sensor TRQ1 and TRQ2 exceeds specified values Torque sensor (Electric power steering column sub-assembly) EPS warning light: Comes on Ignition switch ON again -

WIRING DIAGRAM

C375647E15
0.271,3.01 2.708,3.333 2.438,0.323 10 false Torque Sensor (Electric Power Steering Column Sub-assembly) 5.854,0.615 6.167,0.813 0.313,0.198 10 false 5V 5.083,0.833 5.698,1.031 0.615,0.198 10 false TRQV 5.115,1.406 5.729,1.604 0.615,0.198 10 false TRQ1 5.115,1.896 5.729,2.094 0.615,0.198 10 false TRQ2 5.083,2.26 5.698,2.458 0.615,0.198 10 false TRQG 4.885,0.813 5.042,1.01 0.156,0.198 10 false 8 4.885,1.26 5.042,1.458 0.156,0.198 10 false 9 4.875,1.781 5.031,1.979 0.156,0.198 10 false 1 4.885,2.25 5.042,2.448 0.156,0.198 10 false 2 4.813,2.958 5.125,3.156 0.313,0.198 10 false z5 4.813,3.115 6.948,3.438 2.135,0.323 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
OK:

DTC C1511 and C1512 are not output.



Result:
Result Proceed to
DTCs C1511 and C1512 are not output A
DTC C1511 is output B
DTC C1512 is output C



A

2.CLEAR DTC

B

C

2.CLEAR DTC
a.

Clear the DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>DTC CHECK / CLEAR

Chassis > EMPS > Clear DTCs
50002 142

Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Start the engine.


b.

With the vehicle stopped, turn the steering wheel all the way to the left and right.

HINT:

Turn the wheel both strongly and gently when steering back and forth.



c.

Check for DTCs.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>DTC CHECK / CLEAR

Chassis > EMPS > Trouble Codes
50001 142
OK:

DTC C1513 is not output.



Result:
Proceed to
OK
NG



OK

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY