Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090851 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (engine switch off, or driver door is opened and closed with engine switch on (IG)).

WIRING DIAGRAM

for TMMIN Made


E271706E02
1.438,2.167 3.25,2.531 1.813,0.365 10 false Combination Meter Assembly 1.448,2 3.26,2.167 1.813,0.167 10 false F38 4.979,2.167 6.49,2.552 1.51,0.385 10 false Certification ECU (Smart Key ECU Assembly) 4.99,2.01 6.802,2.177 1.813,0.167 10 false F43 1.708,1.396 2.021,1.594 0.313,0.198 10 false 21 1.979,1.49 2.292,1.688 0.313,0.198 10 false ED 2.552,1.177 2.865,1.375 0.313,0.198 10 false LP 2.823,1.073 3.135,1.271 0.313,0.198 10 false 13 5.104,1.083 5.417,1.281 0.313,0.198 10 false 15 5.375,1.167 5.833,1.365 0.458,0.198 10 false IND


for TMT Made


E374198E03
1.625,1.49 2.083,1.688 0.458,0.198 10 false F38 2.823,1.167 3.281,1.365 0.458,0.198 10 false F39 4.885,1.948 5.344,2.146 0.458,0.198 10 false F43 4.885,2.115 6.406,2.563 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.385,1.177 5.844,1.375 0.458,0.198 10 false IND 5.115,1.031 5.49,1.25 0.375,0.219 10 false 15 1.552,2.01 3.521,2.354 1.969,0.344 10 false Combination Meter Assembly 1.958,1.49 2.417,1.688 0.458,0.198 10 false EP 1.677,1.313 2.052,1.531 0.375,0.219 10 false 21 2.542,1.156 3,1.354 0.458,0.198 10 false LP 2.906,0.979 3.281,1.198 0.375,0.219 10 false 6


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (IMMOBILISER INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

for TMMIN Made

i.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the F38 combination meter assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-13 (LP) - F43-15 (IND) Always Below 1 Ω
F38-21 (ED) - Body ground Always Below 1 Ω
F38-13 (LP) or F43-15 (IND) - Body ground Always 10 kΩ or higher




b.

for TMT Made

i.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


ii.

Disconnect the F38 and F39 combination meter assembly connectors.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F39-6 (LP) - F43-15 (IND) Always Below 1 Ω
F38-21 (ED) - Body ground Always Below 1 Ω
F39-6 (LP) or F43-15 (IND) - Body ground Always 10 kΩ or higher




Result:
Result Proceed to
OK (for TMT Made) A
OK (for TMMIN Made) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR