Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1643/81  Side Satellite Sensor Bus RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag ECU assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

The side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1622/81 Lost communication with Side Airbag Sensor RH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B1632/81 Lost Communication with Rear Airbag Sensor RH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode
B1643/81 Side Satellite Sensor Bus RH Initialization Incomplete Any of the following conditions is met:
·

The airbag ECU assembly detects a line short in the side collision sensor RH circuit (bus 1).

·

The airbag ECU assembly detects a short to ground in the side collision sensor RH circuit (bus 1).

·

The airbag ECU assembly detects a short to B+ in the side collision sensor RH circuit (bus 1).

·

The airbag ECU assembly detects an open in the side collision sensor RH circuit (bus 1).

·

Side airbag sensor assembly RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front door wire RH

·

Side airbag sensor assembly RH

·

No. 2 side airbag sensor assembly RH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C381306E08
1.115,0.875 1.729,1.073 0.615,0.198 10 false BBR+ 1.125,1.76 1.74,1.958 0.615,0.198 10 false BBR- 1.104,3.021 1.719,3.219 0.615,0.198 10 false BCR+ 1.115,3.917 1.729,4.115 0.615,0.198 10 false BCR- 1.573,3.823 1.896,4.083 0.323,0.26 10 false 2 2.906,2.938 3.229,3.198 0.323,0.26 10 false 2 1.573,2.948 1.896,3.208 0.323,0.26 10 false 1 2.917,3.844 3.24,4.104 0.323,0.26 10 false 1 5.313,1.698 5.635,1.958 0.323,0.26 10 false 11 5.385,0.813 5.708,1.073 0.323,0.26 10 false 8 1.573,0.802 1.896,1.063 0.323,0.26 10 false 4 1.573,1.698 1.896,1.958 0.323,0.26 10 false 3 5.552,1.781 6.167,1.979 0.615,0.198 10 false BBR- 5.542,0.885 6.156,1.083 0.615,0.198 10 false BBR+ 3.063,3.021 3.677,3.219 0.615,0.198 10 false BCR+ 3.063,3.927 3.677,4.125 0.615,0.198 10 false BCR- 0.531,4.656 1.146,4.854 0.615,0.198 10 false F157 0.51,4.823 1.719,5.198 1.208,0.375 10 false Side Airbag Sensor Assembly RH 2.677,4.667 3.292,4.865 0.615,0.198 10 false F159 2.677,4.802 4.26,5.167 1.583,0.365 10 false No. 2 Side Airbag Sensor Assembly RH 5.417,4.688 6.031,4.885 0.615,0.198 10 false F120 5.417,4.833 7.021,5.063 1.604,0.229 10 false Airbag ECU Assembly


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than current DTCs B1622/81, B1623/81, B1632/81, B1633/81, B1642/81 and B1643/81 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1642/81 or B1643/81 is output. A
Current DTC B1623/81 is output. B
Current DTC B1632/81 or B1633/81 is output. C
Current DTC B1622/81 is output. D
Current DTCs B1622/81, B1623/81, B1632/81, B1633/81, B1642/81 and B1643/81 are not output. E



A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

21.CHECK CONNECTORS

D

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

E

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238219C33
1.083,0.5 1.583,0.75 0.5,0.25 0.5,3.583 1,3.833 0.5,0.25 1.76,3.76 2.135,4.198 true 1.656,3.771 1.281,4.208 true 1.865,0.844 1.5,1.115 true 2.063,0.625 2.417,1.115 true 2,1.083 2,1.26 false 1.438,2 1.604,2.49 false 1.021,2.479 1.594,2.854 0.573,0.375 10 false D 1.323,2.479 1.615,2.875 0.292,0.396 10 false C 1.781,2.479 2.135,2.844 0.354,0.365 10 false B 2.094,2.479 2.375,2.802 0.281,0.323 10 false A 0.708,2.479 1.083,2.854 0.375,0.375 10 false *1 2.51,2.198 2.813,2.573 0.302,0.375 10 false *2 0.802,0.229 1.094,0.542 0.292,0.313 10 false *a 0.385,3.208 0.813,3.521 0.427,0.313 10 false *b 1.323,1.135 1.823,1.469 0.5,0.333 10 false BBR- 2.292,1.135 2.844,1.406 0.552,0.271 10 false BBR+ 1.177,0.531 1.615,0.865 0.438,0.333 10 false F120 0.594,3.615 1.083,3.917 0.49,0.302 10 false F157 2.021,4.219 2.708,4.49 0.688,0.271 10 false BBR+ 1.115,4.229 1.656,4.521 0.542,0.292 10 false BBR- 1.229,1.896 1.583,2.229 0.354,0.333 10 false *3 1.938,1.292 2.198,1.615 0.26,0.323 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - F157-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C389479C01
0.333,2.292 0.833,2.542 0.5,0.25 1.26,2.865 1.51,2.448 true 1.656,2.448 1.906,2.865 true 1.333,0.542 1.583,0.958 false 0.625,0.927 0.938,1.083 0.313,0.156 10 false *1 2.479,0.635 2.792,0.792 0.313,0.156 10 false *2 1.156,0.448 1.469,0.604 0.313,0.156 10 false *3 0.333,1.76 0.646,1.917 0.313,0.156 10 false *a 1.094,2.875 1.573,3.042 0.479,0.167 10 false BBR- 1.76,2.875 2.24,3.042 0.479,0.167 10 false BBR+ 0.438,2.323 0.917,2.49 0.479,0.167 10 false F157 2.031,0.927 2.198,1.094 0.167,0.167 10 false A 1.719,0.927 1.885,1.094 0.167,0.167 10 false B 1.271,0.927 1.438,1.094 0.167,0.167 10 false C 0.958,0.927 1.125,1.094 0.167,0.167 10 false D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - F157-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C389479C01
0.333,2.292 0.833,2.542 0.5,0.25 1.26,2.865 1.51,2.448 true 1.656,2.448 1.906,2.865 true 1.333,0.542 1.583,0.958 false 0.625,0.927 0.938,1.083 0.313,0.156 10 false *1 2.479,0.635 2.792,0.792 0.313,0.156 10 false *2 1.156,0.448 1.469,0.604 0.313,0.156 10 false *3 0.333,1.76 0.646,1.917 0.313,0.156 10 false *a 1.094,2.875 1.573,3.042 0.479,0.167 10 false BBR- 1.76,2.875 2.24,3.042 0.479,0.167 10 false BBR+ 0.438,2.323 0.917,2.49 0.479,0.167 10 false F157 2.031,0.927 2.198,1.094 0.167,0.167 10 false A 1.719,0.927 1.885,1.094 0.167,0.167 10 false B 1.271,0.927 1.438,1.094 0.167,0.167 10 false C 0.958,0.927 1.125,1.094 0.167,0.167 10 false D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F157-4 (BBR+) - Body ground Ignition switch ON Below 1 V
F157-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C385800C03
0.333,2.281 0.833,2.531 0.5,0.25 1.333,2.958 1.5,2.458 true 1.667,2.448 1.833,2.948 true 1.417,0.458 1.583,0.958 false 0.646,0.927 0.958,1.083 0.313,0.156 10 false *1 2.479,0.646 2.792,0.802 0.313,0.156 10 false *2 1.229,0.375 1.542,0.531 0.313,0.156 10 false *3 0.344,1.74 0.656,1.896 0.313,0.156 10 false *a 0.438,2.313 0.823,2.479 0.385,0.167 10 false F157 1.167,2.969 1.583,3.135 0.417,0.167 10 false BBR- 1.688,2.969 2.104,3.135 0.417,0.167 10 false BBR+ 2.031,0.927 2.344,1.083 0.313,0.156 10 false A 1.271,0.927 1.583,1.083 0.313,0.156 10 false C 0.958,0.927 1.271,1.083 0.313,0.156 10 false D 1.719,0.927 2.031,1.083 0.313,0.156 10 false B
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - Body ground Always 1 MΩ or higher
F157-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C256981C64
0.917,0.5 1.417,0.75 0.5,0.25 0.552,3.583 1.052,3.833 0.5,0.25 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 true 2.26,1.063 1.927,0.667 true 1.344,4.073 1.667,3.698 true 2.146,4.063 1.76,3.698 true 1.698,2.281 1.448,1.865 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.25,1.771 1.573,2.063 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1.021,0.521 1.51,0.813 0.49,0.292 10 false F157 0.646,3.615 1.135,3.906 0.49,0.292 10 false F159 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - F157-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C381318C45
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.771,0.75 1.469,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.302,0.156 1.615,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.167,2.354 1.563,2.542 0.396,0.188 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - F157-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C381318C45
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.771,0.75 1.469,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.302,0.156 1.615,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.167,2.354 1.563,2.542 0.396,0.188 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F157-1 (BCR+) - Body ground Ignition switch ON Below 1 V
F157-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C381318C45
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.771,0.75 1.469,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.302,0.156 1.615,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.167,2.354 1.563,2.542 0.396,0.188 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - Body ground Always 1 MΩ or higher
F157-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag ECU assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642/81 or B1643/81 is output. A
DTC B1647/82 or B1648/82 is output. B
DTCs B1642/81, B1643/81, B1647/82 and B1648/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642/81 or B1643/81 is output. A
DTC B1647/82 or B1648/82 is output. B
DTCs B1642/81, B1643/81, B1647/82 and B1648/82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

C

13.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1622/81 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1622/81 is not output. A
History DTC B1622/81 is output. B



A

14.CHECK CONNECTORS

B

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
14.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

15.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

15.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238219C34
1.083,0.5 1.583,0.75 0.5,0.25 0.5,3.667 1,3.917 0.5,0.25 1.76,3.76 2.135,4.198 true 1.656,3.771 1.281,4.208 true 1.865,0.844 1.5,1.115 true 2.063,0.625 2.417,1.115 true 2,1.083 2,1.26 false 1.417,2 1.594,2.49 false 1.021,2.479 1.594,2.854 0.573,0.375 10 false D 1.323,2.479 1.615,2.875 0.292,0.396 10 false C 1.781,2.479 2.135,2.844 0.354,0.365 10 false B 2.094,2.479 2.375,2.802 0.281,0.323 10 false A 0.708,2.479 1.083,2.854 0.375,0.375 10 false *1 2.51,2.198 2.813,2.573 0.302,0.375 10 false *2 0.802,0.229 1.094,0.542 0.292,0.313 10 false *a 0.385,3.208 0.813,3.521 0.427,0.313 10 false *b 1.323,1.135 1.823,1.469 0.5,0.333 10 false BBR- 2.292,1.135 2.844,1.406 0.552,0.271 10 false BBR+ 1.177,0.521 1.615,0.854 0.438,0.333 10 false F120 0.594,3.688 1.083,3.99 0.49,0.302 10 false F157 2.021,4.219 2.708,4.49 0.688,0.271 10 false BBR+ 1.115,4.229 1.656,4.521 0.542,0.292 10 false BBR- 1.219,1.896 1.573,2.229 0.354,0.333 10 false *3 1.938,1.292 2.198,1.615 0.26,0.323 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - F157-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

16.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

16.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C385800C03
0.333,2.281 0.833,2.531 0.5,0.25 1.333,2.958 1.5,2.458 true 1.667,2.448 1.833,2.948 true 1.417,0.458 1.583,0.958 false 0.646,0.927 0.958,1.083 0.313,0.156 10 false *1 2.479,0.646 2.792,0.802 0.313,0.156 10 false *2 1.229,0.375 1.542,0.531 0.313,0.156 10 false *3 0.344,1.74 0.656,1.896 0.313,0.156 10 false *a 0.438,2.313 0.823,2.479 0.385,0.167 10 false F157 1.167,2.969 1.583,3.135 0.417,0.167 10 false BBR- 1.688,2.969 2.104,3.135 0.417,0.167 10 false BBR+ 2.031,0.927 2.344,1.083 0.313,0.156 10 false A 1.271,0.927 1.583,1.083 0.313,0.156 10 false C 0.958,0.927 1.271,1.083 0.313,0.156 10 false D 1.719,0.927 2.031,1.083 0.313,0.156 10 false B
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - F157-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

17.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C385800C03
0.333,2.281 0.833,2.531 0.5,0.25 1.333,2.958 1.5,2.458 true 1.667,2.448 1.833,2.948 true 1.417,0.458 1.583,0.958 false 0.646,0.927 0.958,1.083 0.313,0.156 10 false *1 2.479,0.646 2.792,0.802 0.313,0.156 10 false *2 1.229,0.375 1.542,0.531 0.313,0.156 10 false *3 0.344,1.74 0.656,1.896 0.313,0.156 10 false *a 0.438,2.313 0.823,2.479 0.385,0.167 10 false F157 1.167,2.969 1.583,3.135 0.417,0.167 10 false BBR- 1.688,2.969 2.104,3.135 0.417,0.167 10 false BBR+ 2.031,0.927 2.344,1.083 0.313,0.156 10 false A 1.271,0.927 1.583,1.083 0.313,0.156 10 false C 0.958,0.927 1.271,1.083 0.313,0.156 10 false D 1.719,0.927 2.031,1.083 0.313,0.156 10 false B
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F157-4 (BBR+) - Body ground Ignition switch ON Below 1 V
F157-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

18.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

18.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C385800C03
0.333,2.281 0.833,2.531 0.5,0.25 1.333,2.958 1.5,2.458 true 1.667,2.448 1.833,2.948 true 1.417,0.458 1.583,0.958 false 0.646,0.927 0.958,1.083 0.313,0.156 10 false *1 2.479,0.646 2.792,0.802 0.313,0.156 10 false *2 1.229,0.375 1.542,0.531 0.313,0.156 10 false *3 0.344,1.74 0.656,1.896 0.313,0.156 10 false *a 0.438,2.313 0.823,2.479 0.385,0.167 10 false F157 1.167,2.969 1.583,3.135 0.417,0.167 10 false BBR- 1.688,2.969 2.104,3.135 0.417,0.167 10 false BBR+ 2.031,0.927 2.344,1.083 0.313,0.156 10 false A 1.271,0.927 1.583,1.083 0.313,0.156 10 false C 0.958,0.927 1.271,1.083 0.313,0.156 10 false D 1.719,0.927 2.031,1.083 0.313,0.156 10 false B
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-4 (BBR+) - Body ground Always 1 MΩ or higher
F157-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1623/81 is output. A
DTC B1628/82 is output. B
DTCs B1623/81 and B1628/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622/81 and B1627/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622/81 is output. A
DTC B1627/82 is output. B
DTCs B1622/81 and B1627/82 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

21.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and No. 2 side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

22.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

22.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C256981C65
0.865,0.5 1.365,0.75 0.5,0.25 0.542,3.594 1.042,3.844 0.5,0.25 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 true 2.26,1.063 1.927,0.667 true 1.344,4.073 1.667,3.698 true 2.146,4.063 1.76,3.698 true 1.719,2.281 1.5,1.833 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.75 1.615,2.042 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 0.958,0.521 1.448,0.813 0.49,0.292 10 false F157 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b 0.646,3.615 1.135,3.906 0.49,0.292 10 false F159
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - F157-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

23.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C381318C46
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.177,2.354 1.594,2.552 0.417,0.198 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - F157-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

24.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C381318C47
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.167,2.354 1.594,2.563 0.427,0.208 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F157-1 (BCR+) - Body ground Ignition switch ON Below 1 V
F157-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

25.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

25.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C381318C47
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.219,0.729 2.531,0.885 0.313,0.156 10 false A 1.906,0.719 2.219,0.875 0.313,0.156 10 false B 1.448,0.719 1.76,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.167,2.354 1.594,2.563 0.427,0.208 10 false F157 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCR+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCR-
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F157-1 (BCR+) - Body ground Always 1 MΩ or higher
F157-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE INSTRUMENT PANEL WIRE

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Connect the connector to the No. 2 side airbag sensor assembly RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632/81 or B1633/81 is output. A
DTC B1637/82 or B1638/82 is output. B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

27.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

27.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH


Interchange the No. 2 side airbag sensor assembly RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632/81 or B1633/81 is output. A
DTC B1637/82 or B1638/82 is output. B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY RH

C

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622/81 and B1627/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622/81 is output. A
DTC B1627/82 is output. B
DTCs B1622/81 and B1627/82 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C