Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0334273 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


HINT:

The procedure described below is for the RH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 62311B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 62331A 6.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 73210 7.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 62413A 8.REMOVE CENTER PILLAR LOWER GARNISH

Hide 89860 9.REMOVE SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B484612

Disconnect the connector from the side airbag sensor assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


i.

Push and hold the white housing lock, and slide the yellow outer connector locking sleeve.

C195226C49
0.876,1.724 1.06,1.894 0.184,0.17 10 *a 3.412,1.745 3.811,1.957 0.399,0.212 10 *a 3.924,1.292 3.924,2.123 false 1.388,1.286 1.388,2.116 false 0.85,0.442 1.038,0.62 0.187,0.178 10 *1 1.135,0.988 1.135,0.533 1.135,0.533 1.047,0.533 false 3.658,0.989 3.658,0.534 3.658,0.534 3.57,0.534 false 3.379,0.47 3.567,0.648 0.187,0.178 10 *1 1.299,2.13 1.486,2.308 0.187,0.178 10 *2 3.827,2.151 4.015,2.329 0.187,0.178 10 *2
*1 Housing Lock *2 Outer Connector Locking Sleeve
*a Slide - -



ii.

Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.



d.
B484613

Remove the nut and side airbag sensor assembly.

NOTICE:

Loosen the nut while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.