Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag ECU assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

The side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1627/82 Lost communication with Side Airbag Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1628/82 Side Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1637/82 Lost Communication with Rear Airbag Sensor LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1638/82 Rear Airbag Sensor Assembly LH Initialization Incomplete
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1647/82 Lost Communication with Side Satellite Sensor Bus LH
·

The airbag ECU assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit.

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode
B1648/82 Side Satellite Sensor Bus LH Initialization Incomplete Any of the following conditions is met:
·

The airbag ECU assembly detects a line short in the side collision sensor LH circuit (bus 1).

·

The airbag ECU assembly detects a short to ground in the side collision sensor LH circuit (bus 1).

·

The airbag ECU assembly detects a short to B+ in the side collision sensor LH circuit (bus 1).

·

The airbag ECU assembly detects an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor assembly LH malfunction

·

No. 2 side airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Front door wire LH

·

Side airbag sensor assembly LH

·

No. 2 side airbag sensor assembly LH

·

Airbag ECU assembly


Does not apply to test/check mode

WIRING DIAGRAM

C381306E09
1.135,0.885 1.75,1.083 0.615,0.198 10 false BBL+ 1.167,1.771 1.781,1.969 0.615,0.198 10 false BBL- 1.135,3.031 1.75,3.229 0.615,0.198 10 false BCL+ 1.156,3.917 1.771,4.115 0.615,0.198 10 false BCL- 1.615,0.792 1.813,1.031 0.198,0.24 10 false 4 1.615,1.708 1.813,1.948 0.198,0.24 10 false 3 1.615,2.948 1.813,3.188 0.198,0.24 10 false 1 2.906,3.844 3.104,4.083 0.198,0.24 10 false 1 2.906,2.938 3.104,3.177 0.198,0.24 10 false 2 1.635,3.844 1.833,4.083 0.198,0.24 10 false 2 3.104,3.031 3.719,3.229 0.615,0.198 10 false BCL+ 3.104,3.938 3.719,4.135 0.615,0.198 10 false BCL- 5.573,0.896 6.188,1.094 0.615,0.198 10 false BBL+ 5.594,1.802 6.208,2 0.615,0.198 10 false BBL- 5.375,0.823 5.573,1.063 0.198,0.24 10 false 8 5.313,1.698 5.583,1.896 0.271,0.198 10 false 15 0.49,4.698 1.104,4.896 0.615,0.198 10 false F158 0.5,4.844 1.74,5.219 1.24,0.375 10 false Side Airbag Sensor Assembly LH 2.74,4.677 3.354,4.875 0.615,0.198 10 false F160 2.729,4.854 4.313,5.26 1.583,0.406 10 false No. 2 Side Airbag Sensor Assembly LH 5.354,4.688 5.969,4.885 0.615,0.198 10 false F119 5.354,4.854 7.083,5.208 1.729,0.354 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than current DTCs B1627/82, B1628/82, B1637/82, B1638/82, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1647/82 or B1648/82 is output. A
Current DTC B1628/82 is output. B
Current DTC B1637/82 or B1638/82 is output. C
Current DTC B1627/82 is output. D
Current DTCs B1627/82, B1628/82, B1637/82, B1638/82, B1647/82 and B1648/82 are not output. E



A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

21.CHECK CONNECTORS

D

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

E

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly, side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238225C30
0.917,0.583 1.417,0.833 0.5,0.25 0.333,3.583 0.833,3.833 0.5,0.25 1.521,3.729 1.198,4.115 true 1.667,3.75 1.99,4.135 true 2,1.125 2,1.323 false 1.917,0.667 1.469,1.146 true 2.135,0.885 2.479,1.146 true 1.333,1.833 1.521,2.26 false 0.948,2.26 1.427,2.635 0.479,0.375 10 false D 1.26,2.26 1.604,2.656 0.344,0.396 10 false C 1.708,2.26 2.073,2.604 0.365,0.344 10 false B 2.021,2.26 2.365,2.667 0.344,0.406 10 false A 0.635,2.26 1.042,2.646 0.406,0.385 10 false *1 2.438,2.271 2.75,2.656 0.313,0.385 10 false *2 0.75,0.292 1.146,0.729 0.396,0.438 10 false *a 0.313,3.177 0.719,3.51 0.406,0.333 10 false *b 1.323,1.167 1.802,1.469 0.479,0.302 10 false BBL+ 2.375,1.156 2.844,1.406 0.469,0.25 10 false BBL- 1.01,0.625 1.5,0.969 0.49,0.344 10 false F119 0.427,3.625 0.927,3.958 0.5,0.333 10 false F158 1.854,4.135 2.417,4.448 0.563,0.313 10 false BBL+ 1.042,4.125 1.604,4.406 0.563,0.281 10 false BBL- 1.167,1.729 1.531,2.021 0.365,0.292 10 false *3 1.927,1.354 2.208,1.688 0.281,0.333 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - F158-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C238226C57
0.333,2.333 0.833,2.583 0.5,0.25 1.5,2.479 1.198,2.833 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.563,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.24,0.146 1.583,0.458 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.438,2.375 0.844,2.688 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - F158-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C238226C57
0.333,2.333 0.833,2.583 0.5,0.25 1.5,2.479 1.198,2.833 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.563,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.24,0.146 1.583,0.458 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.438,2.375 0.844,2.688 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F158-4 (BBL+) - Body ground Ignition switch ON Below 1 V
F158-3 (BBL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C238226C57
0.333,2.333 0.833,2.583 0.5,0.25 1.5,2.479 1.198,2.833 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.563,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.24,0.146 1.583,0.458 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.438,2.375 0.844,2.688 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - Body ground Always 1 MΩ or higher
F158-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C256981C66
0.833,0.5 1.333,0.75 0.5,0.25 0.521,3.667 1,3.917 0.479,0.25 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 true 2.26,1.063 1.927,0.667 true 1.344,4.073 1.667,3.698 true 2.146,4.063 1.76,3.698 true 1.75,2.281 1.563,1.833 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.396,1.729 1.719,2.021 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCL+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCL- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCL- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCL+ 0.927,0.552 1.417,0.844 0.49,0.292 10 false F158 0.594,3.708 1.083,4 0.49,0.292 10 false F160 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - F158-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

8.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C381318C48
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.438,0.719 1.75,0.875 0.313,0.156 10 false C 1.125,0.719 1.438,0.875 0.313,0.156 10 false D 1.177,2.354 1.604,2.552 0.427,0.198 10 false F158 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - F158-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C381318C48
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.438,0.719 1.75,0.875 0.313,0.156 10 false C 1.125,0.719 1.438,0.875 0.313,0.156 10 false D 1.177,2.354 1.604,2.552 0.427,0.198 10 false F158 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F158-1 (BCL+) - Body ground Ignition switch ON Below 1 V
F158-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C381318C48
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.375,0.156 1.688,0.313 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.438,0.719 1.75,0.875 0.313,0.156 10 false C 1.125,0.719 1.438,0.875 0.313,0.156 10 false D 1.177,2.354 1.604,2.552 0.427,0.198 10 false F158 1.521,2.823 2.01,3.01 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - Body ground Always 1 MΩ or higher
F158-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the No. 2 side airbag sensor assembly LH and airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647/82 or B1648/82 is output. A
DTC B1642/81 or B1643/81 is output. B
DTCs B1642/81, B1643/81, B1647/82 and B1648/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

12.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642/81, B1643/81, B1647/82 and B1648/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1647/82 or B1648/82 is output. A
DTC B1642/81 or B1643/81 is output. B
DTCs B1642/81, B1643/81, B1647/82 and B1648/82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

C

13.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1627/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1627/82 is not output. A
History DTC B1627/82 is output. B



A

14.CHECK CONNECTORS

B

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
14.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and side airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

15.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

15.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C238225C31
0.333,3.583 0.833,3.833 0.5,0.25 0.938,0.542 1.438,0.792 0.5,0.25 1.521,3.729 1.198,4.115 true 1.646,3.729 1.969,4.115 true 2,1.125 2,1.323 false 1.938,0.667 1.49,1.146 true 2.135,0.885 2.479,1.146 true 1.333,1.833 1.521,2.271 false 0.948,2.26 1.427,2.635 0.479,0.375 10 false D 1.26,2.26 1.604,2.656 0.344,0.396 10 false C 1.708,2.26 2.073,2.604 0.365,0.344 10 false B 2.021,2.26 2.365,2.667 0.344,0.406 10 false A 0.635,2.26 1.042,2.646 0.406,0.385 10 false *1 2.438,2.271 2.75,2.656 0.313,0.385 10 false *2 0.75,0.292 1.146,0.729 0.396,0.438 10 false *a 0.313,3.177 0.719,3.51 0.406,0.333 10 false *b 1.323,1.167 1.802,1.469 0.479,0.302 10 false BBL+ 2.375,1.156 2.844,1.406 0.469,0.25 10 false BBL- 1.052,0.583 1.542,0.927 0.49,0.344 10 false F119 0.427,3.604 0.927,3.938 0.5,0.333 10 false F158 1.854,4.135 2.417,4.448 0.563,0.313 10 false BBL+ 1.042,4.125 1.604,4.406 0.563,0.281 10 false BBL- 1.177,1.677 1.542,1.969 0.365,0.292 10 false *3 1.927,1.354 2.208,1.688 0.281,0.333 10 false *4
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - F158-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

16.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

16.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C238226C58
0.333,2.333 0.833,2.583 0.5,0.25 1.531,2.458 1.229,2.813 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.573,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.26,0.094 1.604,0.406 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.417,2.365 0.823,2.677 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - F158-3 (BBL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

17.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C238226C58
0.333,2.333 0.833,2.583 0.5,0.25 1.531,2.458 1.229,2.813 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.573,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.26,0.094 1.604,0.406 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.417,2.365 0.823,2.677 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F158-4 (BBL+) - Body ground Ignition switch ON Below 1 V
F158-3 (BBL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

18.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

18.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C238226C58
0.333,2.333 0.833,2.583 0.5,0.25 1.531,2.458 1.229,2.813 true 1.677,2.458 1.979,2.813 true 1.417,0.25 1.573,0.75 false 0.667,0.76 1.083,1.063 0.417,0.302 10 false *1 1.26,0.094 1.604,0.406 0.344,0.313 10 false *3 1,0.76 1.229,1.052 0.229,0.292 10 false D 1.292,0.76 1.521,1.063 0.229,0.302 10 false C 1.75,0.76 2.01,1.104 0.26,0.344 10 false B 2.063,0.76 2.333,1.052 0.271,0.292 10 false A 2.469,0.76 2.781,1.042 0.313,0.281 10 false *2 0.375,1.896 0.719,2.156 0.344,0.26 10 false *a 1.073,2.833 1.542,3.094 0.469,0.26 10 false BBL- 0.417,2.365 0.823,2.677 0.406,0.313 10 false F158 1.875,2.833 2.333,3.052 0.458,0.219 10 false BBL+
*1 Side Airbag Sensor Assembly LH
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-4 (BBL+) - Body ground Always 1 MΩ or higher
F158-3 (BBL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connector to the airbag ECU assembly.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623/81 and B1628/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1628/82 is output. A
DTC B1623/81 is output. B
DTCs B1623/81 and B1628/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622/81 and B1627/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627/82 is output. A
DTC B1622/81 is output. B
DTCs B1622/81 and B1627/82 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

21.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly LH and No. 2 side airbag sensor assembly LH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

22.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

22.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
C256981C67
0.854,0.5 1.333,0.75 0.479,0.25 0.5,3.5 1,3.75 0.5,0.25 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 true 2.26,1.063 1.927,0.667 true 1.344,4.073 1.667,3.698 true 2.146,4.063 1.76,3.698 true 1.698,2.281 1.5,1.833 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.344,1.677 1.667,1.969 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCL+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCL- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCL- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCL+ 0.958,0.531 1.448,0.823 0.49,0.292 10 false F158 0.604,3.542 1.094,3.833 0.49,0.292 10 false F160 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly LH)


Using a service wire, connect terminals 2 (BCL+) and 1 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - F158-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

23.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C381318C49
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.427,0.104 1.74,0.26 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.458,0.719 1.771,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.188,2.354 1.615,2.594 0.427,0.24 10 false F158 1.51,2.813 2,3 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - F158-2 (BCL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

24.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C381318C49
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.427,0.104 1.74,0.26 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.458,0.719 1.771,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.188,2.354 1.615,2.594 0.427,0.24 10 false F158 1.51,2.813 2,3 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F158-1 (BCL+) - Body ground Ignition switch ON Below 1 V
F158-2 (BCL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

25.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

25.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C381318C49
1.083,2.333 1.583,2.583 0.5,0.25 1.729,2.823 2.073,2.469 true 2.448,2.823 2.229,2.458 true 1.75,0.75 1.583,0.25 false 0.813,0.698 1.125,0.854 0.313,0.156 10 false *1 2.469,0.698 2.781,0.854 0.313,0.156 10 false *2 1.427,0.104 1.74,0.26 0.313,0.156 10 false *3 0.99,1.865 1.302,2.021 0.313,0.156 10 false *a 2.208,0.729 2.521,0.885 0.313,0.156 10 false A 1.896,0.719 2.208,0.875 0.313,0.156 10 false B 1.458,0.719 1.771,0.875 0.313,0.156 10 false C 1.146,0.719 1.458,0.875 0.313,0.156 10 false D 1.188,2.354 1.615,2.594 0.427,0.24 10 false F158 1.51,2.813 2,3 0.49,0.188 10 false BCL+ 2.313,2.823 2.802,3.01 0.49,0.188 10 false BCL-
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly LH
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F158-1 (BCL+) - Body ground Always 1 MΩ or higher
F158-2 (BCL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH

NG

REPLACE INSTRUMENT PANEL WIRE

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Connect the connector to the No. 2 side airbag sensor assembly LH.


b.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637/82 or B1638/82 is output. A
DTC B1632/81 or B1633/81 is output. B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

27.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C

27.CHECK NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH


Interchange the No. 2 side airbag sensor assembly LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632/81, B1633/81, B1637/82 and B1638/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1637/82 or B1638/82 is output. A
DTC B1632/81 or B1633/81 is output. B
DTCs B1632/81, B1633/81, B1637/82 and B1638/82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the No. 2 side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE NO. 2 SIDE AIRBAG SENSOR ASSEMBLY LH

C

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY LH
a.
C238224C02
0.802,1.01 1.573,1.542 0.771,0.531 10 *1 2.313,1.021 2.708,1.417 0.396,0.396 10 *2 1.875,1.01 2.417,1.458 0.542,0.448 10 A 1.719,1.01 2.219,1.427 0.5,0.417 10 B 1.271,1.01 1.688,1.427 0.417,0.417 10 C 1.115,1.01 1.688,1.5 0.573,0.49 10 D
*1 Side Airbag Sensor Assembly RH
*2 Airbag ECU Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622/81 and B1627/82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1627/82 is output. A
DTC B1622/81 is output. B
DTCs B1622/81 and B1627/82 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly LH and RH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH

C